Searched refs:output (Results 4151 – 4175 of 6165) sorted by relevance
1...<<161162163164165166167168169170>>...247
| /openbmc/linux/Documentation/devicetree/bindings/hwmon/ |
| H A D | national,lm90.yaml | 46 output.
|
| /openbmc/linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | qcom,msm8960-pinctrl.yaml | 147 output-low;
|
| /openbmc/linux/Documentation/gpu/ |
| H A D | msm-crash-dump.rst | 9 This document describes how the output is formatted.
|
| /openbmc/linux/Documentation/bpf/ |
| H A D | linux-notes.rst | 67 * Register R0 is an implicit output which contains the data fetched from
|
| /openbmc/linux/lib/kunit/ |
| H A D | Kconfig | 52 KUnit tests run during boot and output the results to the debug log
|
| /openbmc/linux/samples/vfio-mdev/ |
| H A D | README.rst | 75 In the Linux guest VM, dmesg output for the device is as follows:
|
| /openbmc/linux/arch/arm/boot/dts/st/ |
| H A D | stih407-clock.dtsi | 131 clock-output-names = "clk-m-a9-ext2f-div2";
|
| /openbmc/linux/arch/arm/boot/dts/intel/pxa/ |
| H A D | pxa27x.dtsi | 115 clock-output-names = "qci_mclk";
|
| /openbmc/linux/arch/arm/boot/dts/rockchip/ |
| H A D | rk3288-evb-act8846.dts | 68 clock-output-names = "xin32k";
|
| H A D | rv1108-elgin-r1.dts | 55 clock_in_out = "output";
|
| /openbmc/linux/arch/arm64/boot/dts/renesas/ |
| H A D | ulcb-kf-audio-graph-card2-mix+split.dtsi | 10 * The HDMI output is ignored due to the limited number of subdevices
|
| /openbmc/linux/net/ipv6/ |
| H A D | addrconf_core.c | 195 int (*output)(struct net *, struct sock *, struct sk_buff *)) in eafnosupport_ipv6_fragment()
|
| /openbmc/linux/Documentation/rust/ |
| H A D | general-information.rst | 32 xdg-open Documentation/output/rust/rustdoc/kernel/index.html
|
| /openbmc/linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3368-evb.dtsi | 132 clock_in_out = "output";
|
| /openbmc/linux/drivers/iio/dac/ |
| H A D | vf610_dac.c | 107 .output = 1, \
|
| H A D | ad7303.c | 182 .output = 1, \
|
| /openbmc/linux/arch/arm64/boot/dts/allwinner/ |
| H A D | sun50i-a100-allwinner-perf1.dts | 51 x-powers,drive-vbus-en; /* set N_VBUSEN as output pin */
|
| /openbmc/linux/arch/arm/boot/dts/aspeed/ |
| H A D | aspeed-bmc-vegman-n110.dts | 50 /* SGPIO lines. even: input, odd: output */
|
| /openbmc/linux/arch/arm64/boot/dts/amlogic/ |
| H A D | meson-sm1-bananapi-m5.dts | 111 /* i2s jack output interface */
|
| H A D | meson-a1.dtsi | 170 clock-output-names = "xtal";
|
| /openbmc/linux/Documentation/devicetree/bindings/regulator/ |
| H A D | gpio-regulator.yaml | 42 output mode (most notably linux), this array provides the state of GPIO
|
| /openbmc/linux/arch/arm64/boot/dts/qcom/ |
| H A D | sm8350-sony-xperia-sagami-pdx215.dts | 86 output-high;
|
| /openbmc/linux/arch/arm/boot/dts/nspire/ |
| H A D | nspire.dtsi | 71 regulator-name = "USB VBUS output";
|
| /openbmc/webui-vue/docs/guide/guidelines/ |
| H A D | internationalization.md | 33 function is used to output the translation messages.
|
| /openbmc/phosphor-power/phosphor-regulators/docs/config_file/ |
| H A D | compare_vpd.md | 24 a VPD keyword value. For example, you could set the output voltage only for
|
1...<<161162163164165166167168169170>>...247