/openbmc/linux/Documentation/devicetree/bindings/net/dsa/ |
H A D | nxp,sja1105.yaml | 103 Disable tunable delay lines using 0 ps, or enable them and select
|
/openbmc/linux/Documentation/devicetree/bindings/gpio/ |
H A D | sprd,gpio-eic.yaml | 93 The interrupt shared by all GPIO lines for this controller.
|
/openbmc/linux/arch/arm/boot/dts/ti/omap/ |
H A D | omap3-overo-common-lcd43.dtsi | 86 data-lines = <24>;
|
/openbmc/linux/arch/arm/boot/dts/st/ |
H A D | ste-href-tvk1281618-r3.dtsi | 188 /* Accelerometer interrupt lines 1 & 2 */
|
/openbmc/linux/arch/arm/mach-pxa/ |
H A D | sleep.S | 163 @ force address lines low by reading at physical address 0
|
/openbmc/linux/Documentation/ABI/testing/ |
H A D | sysfs-bus-event_source-devices-events | 50 Examples (each of these lines would be in a separate file):
|
/openbmc/linux/arch/arm64/boot/dts/mediatek/ |
H A D | mt8183-kukui-kakadu.dtsi | 121 /* 192 lines */
|
/openbmc/openbmc/poky/meta/recipes-multimedia/gstreamer/ |
H A D | gstreamer1.0-plugins-base_1.22.11.bb | 12 file://0002-ssaparse-enhance-SSA-text-lines-parsing.patch \
|
/openbmc/phosphor-power/phosphor-regulators/docs/config_file/ |
H A D | phase_fault_detection.md | 50 | comments | no | array of strings | One or more comment lines descr…
|
/openbmc/linux/drivers/video/fbdev/ |
H A D | tridentfb.c | 882 static void set_number_of_lines(struct tridentfb_par *par, int lines) in set_number_of_lines() argument 885 if (lines > 1024) in set_number_of_lines() 887 else if (lines > 768) in set_number_of_lines() 889 else if (lines > 600) in set_number_of_lines() 891 else if (lines > 480) in set_number_of_lines()
|
/openbmc/linux/Documentation/devicetree/bindings/mmc/ |
H A D | sdhci-st.txt | 38 - bus-width: Number of data lines.
|
/openbmc/linux/drivers/ssb/ |
H A D | Kconfig | 89 for some Broadcom SoCs from the BCM47xx and BCM53xx lines.
|
/openbmc/u-boot/doc/ |
H A D | README.avb2 | 100 lines to device configuration mk file:
|
H A D | README.i2c | 25 GPIO lines are shared between the AP and EC to manage the bus. The AP and EC
|
/openbmc/phosphor-pid-control/ |
H A D | tuning.md | 57 logging lines are throttled, unless it has been at least 60 seconds since the
|
/openbmc/linux/Documentation/devicetree/bindings/spi/ |
H A D | spi-controller.yaml | 34 So if, for example, the controller has 4 CS lines, and the
|
/openbmc/linux/Documentation/devicetree/bindings/serial/ |
H A D | nvidia,tegra20-hsuart.yaml | 55 description: Enable modem interrupts. Should be enable only if all 8 lines of UART controller
|
/openbmc/qemu/docs/devel/ |
H A D | docs.rst | 31 ``SRST`` starts a reStructuredText section. Following lines
|
H A D | decodetree.rst | 207 subsequent lines indented two spaces, and ending with a lone 209 required indentation of the lines within the nested group to two
|
/openbmc/linux/mm/ |
H A D | slab.c | 1470 static void print_objinfo(struct kmem_cache *cachep, void *objp, int lines) in print_objinfo() argument 1485 for (i = 0; i < size && lines; i += 16, lines--) { in print_objinfo() 1498 int lines = 0; in check_poison_obj() local 1514 if (lines == 0) { in check_poison_obj() 1527 lines++; in check_poison_obj() 1529 if (lines > 5) in check_poison_obj() 1533 if (lines != 0) { in check_poison_obj()
|
/openbmc/linux/Documentation/timers/ |
H A D | highres.rst | 125 The framework adds about 700 lines of code which results in a 2KB increase of 126 the kernel binary size. The conversion of i386 removes about 100 lines of 136 adding the dynamic tick specific calls to the idle routine (a total of 3 lines
|
/openbmc/openbmc/poky/meta-poky/conf/templates/default/ |
H A D | local.conf.sample | 165 # run tests against any SDK that are built. To enable this uncomment these lines. 231 # use of these by uncommenting some of the following lines. This will mean the build uses 238 # (CDN) kindly provided by JSDelivr, uncomment one of the SSTATE_MIRRORS lines, not both.
|
/openbmc/linux/Documentation/admin-guide/ |
H A D | dynamic-debug-howto.rst | 198 line 1600-1605 // the six lines from line 1600 to line 1605 199 line -1605 // the 1605 lines from line 1 to line 1605 200 line 1600- // all lines from line 1600 to the end of the file
|
/openbmc/linux/drivers/net/wireless/ralink/rt2x00/ |
H A D | rt2x00debug.c | 305 unsigned int lines = 1 + intf->rt2x00dev->data_queues; in rt2x00debug_read_queue_stats() local 313 data = kcalloc(lines, MAX_LINE_LENGTH, GFP_KERNEL); in rt2x00debug_read_queue_stats()
|
/openbmc/openbmc/poky/bitbake/contrib/vim/indent/ |
H A D | bitbake.vim | 41 let s:maxoff = 50 " maximum number of lines to look backwards for () 206 " If the current line begins with a keyword that lines up with "try"
|