| /openbmc/linux/drivers/video/fbdev/omap2/omapfb/dss/ |
| H A D | dsi.c | 230 u8 polarity; member
1824 unsigned polarity, lane_number; in dsi_set_lane_config() local
1835 polarity = dsi->lanes[t].polarity; in dsi_set_lane_config()
1838 r = FLD_MOD(r, polarity, offset + 3, offset + 3); in dsi_set_lane_config()
1960 unsigned p = dsi->lanes[i].polarity; in dsi_cio_enable_lane_override()
3799 lanes[lane].polarity = pol; in dsi_configure_pins()
|
| /openbmc/linux/Documentation/userspace-api/media/drivers/ |
| H A D | omap3isp-uapi.rst | 29 of the VS signal polarity. This is automatically correct when using the serial
|
| /openbmc/linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3568-nanopi-r5s.dtsi | 512 rockchip,hw-tshut-polarity = <0>;
|
| H A D | px30-evb.dts | 595 rockchip,hw-tshut-polarity = <1>;
|
| H A D | rk3566-lubancat-1.dts | 498 rockchip,hw-tshut-polarity = <0>;
|
| H A D | rk3399-rock960.dtsi | 567 rockchip,hw-tshut-polarity = <1>;
|
| H A D | rk3399-pinephone-pro.dts | 570 rockchip,hw-tshut-polarity = <1>;
|
| H A D | rk3568-odroid-m1.dts | 665 rockchip,hw-tshut-polarity = <0>;
|
| H A D | rk3568-lubancat-2.dts | 580 rockchip,hw-tshut-polarity = <0>;
|
| H A D | rk3568-evb1-v10.dts | 613 rockchip,hw-tshut-polarity = <0>;
|
| H A D | rk3399-rock-4c-plus.dts | 605 rockchip,hw-tshut-polarity = <1>;
|
| /openbmc/linux/arch/arm/boot/dts/rockchip/ |
| H A D | rk3288-firefly.dtsi | 519 rockchip,hw-tshut-polarity = <0>;
|
| /openbmc/linux/drivers/leds/rgb/ |
| H A D | leds-qcom-lpg.c | 1002 if (state->polarity != PWM_POLARITY_NORMAL) in lpg_pwm_apply()
1076 state->polarity = PWM_POLARITY_NORMAL; in lpg_pwm_get_state()
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-bus-counter | 408 What: /sys/bus/counter/devices/counterX/signalY/polarity
412 Active level of Signal Y. The following polarity values are
|
| /openbmc/linux/drivers/memory/ |
| H A D | omap-gpmc.c | 235 u32 polarity; member
1080 waitpin->polarity = p->wait_pin_polarity; in gpmc_alloc_waitpin()
1083 if (p->wait_pin_polarity != waitpin->polarity || in gpmc_alloc_waitpin()
|
| /openbmc/linux/Documentation/spi/ |
| H A D | spi-summary.rst | 100 - CPOL indicates the initial clock polarity. CPOL=0 means the
122 a slave, and the slave can tell the chosen polarity by sampling the
124 support for example both modes 0 and 3: they don't care about polarity,
|
| /openbmc/u-boot/drivers/usb/host/ |
| H A D | Kconfig | 169 Set the USB Power pin polarity to be high active (PWR_POL)
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | rk3288-phycore-som.dtsi | 493 rockchip,hw-tshut-polarity = <0>;
|
| H A D | rk3288-popmetal.dtsi | 500 rockchip,hw-tshut-polarity = <0>;
|
| /openbmc/linux/arch/powerpc/boot/dts/ |
| H A D | turris1x.dts | 47 polarity = <0x00>;
|
| /openbmc/u-boot/include/ |
| H A D | ec_commands.h | 4036 uint8_t polarity; member
4043 uint8_t polarity; member
|
| /openbmc/linux/Documentation/fb/ |
| H A D | matroxfb.rst | 279 sync:X sync. pulse - bit 0 inverts HSYNC polarity, bit 1 VSYNC polarity.
|
| /openbmc/linux/drivers/acpi/acpica/ |
| H A D | rsserial.c | 58 {ACPI_RSC_2BITFLAG, ACPI_RS_OFFSET(data.gpio.polarity),
|
| /openbmc/linux/arch/arm/boot/dts/nvidia/ |
| H A D | tegra30-asus-nexus7-grouper-common.dtsi | 945 summit,inok-polarity = <SMB3XX_SYSOK_INOK_ACTIVE_LOW>;
962 * Active INOK disables SMB347 output, so polarity
|
| /openbmc/linux/drivers/gpu/drm/omapdrm/dss/ |
| H A D | dsi.c | 1299 unsigned int polarity, lane_number; in dsi_set_lane_config() local
1310 polarity = dsi->lanes[t].polarity; in dsi_set_lane_config()
1313 r = FLD_MOD(r, polarity, offset + 3, offset + 3); in dsi_set_lane_config()
2984 lanes[lane].polarity = pol; in dsi_configure_pins()
|