| /openbmc/linux/drivers/gpu/drm/amd/display/dc/dcn32/ |
| H A D | dcn32_resource.c | 535 SRII(PIXEL_RATE_CNTL, OTG, 0), \
536 SRII(PIXEL_RATE_CNTL, OTG, 1),\
537 SRII(PIXEL_RATE_CNTL, OTG, 2),\
538 SRII(PIXEL_RATE_CNTL, OTG, 3),\
539 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 0),\
540 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 1),\
541 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 2),\
542 SRII(PHYPLL_PIXEL_RATE_CNTL, OTG, 3),\
|
| /openbmc/linux/Documentation/devicetree/bindings/phy/ |
| H A D | nvidia,tegra186-xusb-padctl.yaml | 257 supports OTG or peripheral mode. If present, the port
295 supports OTG or peripheral mode. If present, the port
333 supports OTG or peripheral mode. If present, the port
|
| H A D | nvidia,tegra210-xusb-padctl.yaml | 376 supports OTG or peripheral mode. If present, the port
414 supports OTG or peripheral mode. If present, the port
452 supports OTG or peripheral mode. If present, the port
490 supports OTG or peripheral mode. If present, the port
|
| H A D | nvidia,tegra124-xusb-padctl.yaml | 354 supports OTG or peripheral mode. If present, the port
389 supports OTG or peripheral mode. If present, the port
424 supports OTG or peripheral mode. If present, the port
|
| /openbmc/linux/drivers/usb/gadget/udc/ |
| H A D | Kconfig | 236 USB2.0 OTG controller, which can be configured as high speed or
258 This IP is different to the High Speed OTG IP that can be enabled
305 The UDC port supports OTG operation, and may be used as a host port
306 if it's not being used to implement peripheral or OTG roles.
|
| /openbmc/u-boot/board/theobroma-systems/puma_rk3399/ |
| H A D | README | 80 rkdeveloptool allows to flash the on-board eMMC via the USB OTG interface with
|
| /openbmc/u-boot/board/amlogic/q200/ |
| H A D | README.khadas-vim2 | 13 - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG
|
| /openbmc/u-boot/board/amlogic/p212/ |
| H A D | README.khadas-vim | 13 - 2 x USB 2.0 Host, 1 x USB 2.0 Type-C OTG
|
| /openbmc/linux/Documentation/devicetree/bindings/power/supply/ |
| H A D | summit,smb347-charger.yaml | 36 description: Provide power for USB OTG
|
| /openbmc/linux/arch/arm64/boot/dts/freescale/ |
| H A D | imx8mm-var-som-symphony.dts | 90 /* USB 3.0 OTG (usbotg1) / SATA port switch, set to USB 3.0 */
|
| /openbmc/u-boot/board/hisilicon/hikey/ |
| H A D | README | 94 the hisi-idt.py utility. Then connect a USB A to B mini cable from your PC to the USB OTG port of H…
116 Note: To get USB host working, also disconnect the USB OTG cable used for flashing. Otherwise you
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | sun4i-a10-gemei-g9.dts | 70 * OTG
|
| H A D | sun8i-h2-plus-orangepi-zero.dts | 184 * power up the board; when it's used as OTG port, this VBUS is
|
| /openbmc/linux/arch/arm/boot/dts/allwinner/ |
| H A D | sun4i-a10-gemei-g9.dts | 70 * OTG
|
| H A D | sun8i-h2-plus-bananapi-m2-zero.dts | 268 * OTG. The Vbus of these two connectors are connected together, so
|
| H A D | sun8i-h2-plus-orangepi-zero.dts | 204 * power up the board; when it's used as OTG port, this VBUS is
|
| /openbmc/u-boot/doc/ |
| H A D | README.rockchip | 105 Connect your board's OTG port to your computer.
303 - Boot U-Boot proper over USB OTG (at present only SPL works)
320 over USB OTG. This is a very simple format - just the string RK32 (as 4 bytes)
|
| /openbmc/u-boot/board/freescale/ls2080ardb/ |
| H A D | README | 35 - Second USB 3.0 port configured as OTG with micro-AB connector
|
| /openbmc/u-boot/drivers/fastboot/ |
| H A D | Kconfig | 61 Some boards have USB OTG controller other than 0. Define this
|
| /openbmc/linux/drivers/usb/musb/ |
| H A D | Kconfig | 3 # USB Dual Role (OTG-ready) Controller Drivers
|
| /openbmc/linux/arch/arm/boot/dts/qcom/ |
| H A D | qcom-apq8064-asus-nexus7-flo.dts | 344 /* OTG */
|
| H A D | qcom-apq8064-ifc6410.dts | 345 /* OTG */
|
| /openbmc/linux/arch/arm/boot/dts/nxp/imx/ |
| H A D | imx7d-cl-som-imx7.dts | 291 MX7D_PAD_LPSR_GPIO1_IO05__GPIO1_IO5 0x14 /* OTG PWREN */
|
| /openbmc/openbmc/meta-raspberrypi/recipes-bsp/bootfiles/ |
| H A D | rpi-config_git.bb | 258 # DWC2 USB OTG support
260 echo "# Enable USB OTG mode" >> $CONFIG
|
| /openbmc/linux/arch/arm64/boot/dts/rockchip/ |
| H A D | rk3568-lubancat-2.dts | 613 /* USB OTG/USB Host_1 USB 2.0 Comb */
658 /* MULTI_PHY0 For SATA0, USB3.0 OTG Only USB2.0 */
|