| /openbmc/linux/arch/arc/boot/dts/ |
| H A D | hsdk.dts | 165 * to 50000000 Hz until we fix dw sdio driver itself.
|
| /openbmc/linux/tools/power/cpupower/po/ |
| H A D | it.po | 607 "3. FREQuencies can be passed in Hz, kHz (default), MHz, GHz, or THz\n"
609 " (FREQuency in kHz =^ Hz * 0.001 =^ MHz * 1000 =^ GHz * 1000000).\n"
616 "3. le FREQuenze possono essere specuficate in Hz, kHz (default), MHz, GHz, "
619 " (FREQuenza in kHz =^ Hz * 0.001 =^ MHz * 1000 =^ GHz * 1000000).\n"
|
| H A D | pt.po | 609 "3. FREQuencies can be passed in Hz, kHz (default), MHz, GHz, or THz\n"
611 " (FREQuency in kHz =^ Hz * 0.001 =^ MHz * 1000 =^ GHz * 1000000).\n"
618 "3. FREQuências podem ser usadas em Hz, kHz (padrão), MHz, GHz, o THz\n"
620 " (FREQuência em kHz =^ Hz * 0.001 =^ MHz * 1000 =^ GHz * 1000000).\n"
|
| H A D | cs.po | 602 "3. FREQuencies can be passed in Hz, kHz (default), MHz, GHz, or THz\n"
604 " (FREQuency in kHz =^ Hz * 0.001 =^ MHz * 1000 =^ GHz * 1000000).\n"
611 "3. Frekvence (FREQ) mohou být zadány v Hz, kHz (výchozí), MHz, GHz nebo THz\n"
613 " (FREQ v kHz =^ Hz * 0,001 = ^ MHz * 1000 =^ GHz * 1000000)\n"
|
| H A D | ka.po | 637 "3. FREQuencies can be passed in Hz, kHz (default), MHz, GHz, or THz\n"
639 " (FREQuency in kHz =^ Hz * 0.001 =^ MHz * 1000 =^ GHz * 1000000).\n"
647 " (სიხშირე in kHz(კილოჰერცი) =^ Hz(ჰერცი) * 0.001 =^ MHz(მეგაჰერცი) * 1000 "
|
| /openbmc/linux/Documentation/devicetree/bindings/memory-controllers/ |
| H A D | nvidia,tegra30-emc.yaml | 67 Memory clock rate in Hz.
|
| /openbmc/linux/drivers/leds/ |
| H A D | Kconfig | 472 known modes: off, blink at 0.5Hz and blink at 1Hz.
477 value 0 means off, 1..127 means blink at 0.5Hz and 128..255 means
478 blink at 1Hz.
|
| /openbmc/linux/Documentation/admin-guide/media/ |
| H A D | si4713.rst | 69 Capabilities : 62.5 Hz stereo rds
|
| H A D | ivtv.rst | 148 (signed 16 bit Little Endian, 48000 Hz, stereo pcm) capture.
|
| /openbmc/u-boot/drivers/mtd/spi/ |
| H A D | Kconfig | 67 int "SPI Flash default speed in Hz"
|
| /openbmc/linux/Documentation/devicetree/bindings/iio/adc/ |
| H A D | st,stm32-dfsdm-adc.yaml | 56 SPI clock OUT frequency (Hz). Requested only for SPI master mode.
|
| /openbmc/linux/Documentation/devicetree/bindings/mfd/ |
| H A D | stericsson,db8500-prcmu.yaml | 265 since even thought it has a very low resolution (32768 Hz) it is
|
| /openbmc/linux/Documentation/gpu/ |
| H A D | drm-usage-stats.rst | 115 - drm-maxfreq-<keystr>: <uint> [Hz|MHz|KHz]
|
| /openbmc/linux/arch/arm/boot/dts/ti/omap/ |
| H A D | dm814x-clocks.dtsi | 216 /* Optional 32768Hz crystal or clock on RTCOSC pins */
|
| /openbmc/linux/arch/arm/boot/dts/samsung/ |
| H A D | s5pv210-goni.dts | 427 /* 480x800@55Hz */
|
| /openbmc/linux/Documentation/hwmon/ |
| H A D | lm93.rst | 138 enabled if the PWM output frequency is 22500 Hz (see below).
164 PWM Output Frequencies (in Hz):
|
| H A D | f71805f.rst | 150 from 187.5 kHz (default) to 31 Hz. The best frequency depends on the
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | sun8i-a83t-bananapi-m3.dts | 102 /* The WiFi low power clock must be 32768 Hz */
|
| H A D | exynos5420-peach-pit.dts | 169 * fix the 30Hz no display issue
|
| H A D | sun8i-a83t-tbs-a711.dts | 82 /* 1024x600 @60Hz */
|
| /openbmc/linux/Documentation/fb/ |
| H A D | vesafb.rst | 100 booting linux. If you are not happy with the 60 Hz refresh rate, you
|
| H A D | sisfb.rst | 84 specified, it defaults to 8. If no rate is given, it defaults to 60Hz. Depth 32
|
| /openbmc/linux/Documentation/devicetree/bindings/interconnect/ |
| H A D | samsung,exynos-bus.yaml | 207 Hz.
|
| /openbmc/qemu/hw/timer/ |
| H A D | trace-events | 78 …eq_hz, uint64_t period_ns, uint64_t delay_s) "timer frequency: %" PRIu64 " Hz, period: %" PRIu64 "…
|
| /openbmc/linux/Documentation/scsi/ |
| H A D | ufs.rst | 206 is interpreted as frequency in Hz and must match one of the values given in
|