/openbmc/linux/Documentation/hwmon/ |
H A D | max6650.rst | 71 clock: The clock frequency in Hz of the chip the driver should assume [254000]
|
/openbmc/linux/Documentation/devicetree/bindings/memory-controllers/ |
H A D | nvidia,tegra124-mc.yaml | 61 Memory clock rate in Hz.
|
/openbmc/linux/Documentation/devicetree/bindings/media/i2c/ |
H A D | mipi-ccs.yaml | 54 description: Frequency of the external clock to the sensor in Hz.
|
H A D | sony,imx290.yaml | 48 description: Frequency of the xclk clock in Hz
|
/openbmc/linux/Documentation/devicetree/bindings/nios2/ |
H A D | nios2.txt | 16 - clock-frequency: Contains the clock frequency for CPU, in Hz.
|
/openbmc/linux/Documentation/devicetree/bindings/i2c/ |
H A D | i2c-mt65xx.yaml | 89 SCL frequency to use (in Hz). If omitted, 100kHz is used.
|
H A D | snps,designware-i2c.yaml | 64 description: Desired I2C bus clock frequency in Hz
|
H A D | opencores,i2c-ocores.yaml | 71 Frequency of the controller clock in Hz. Mutually exclusive with clocks.
|
H A D | i2c-exynos5.yaml | 41 Desired operating frequency in Hz of the bus.
|
/openbmc/linux/arch/m68k/q40/ |
H A D | README | 91 - 50 or 200 Hz - level 2, !!THIS CAN'T BE DISABLED!! 94 Linux uses the 200 Hz interrupt for timer and beep by default.
|
/openbmc/linux/Documentation/iio/ |
H A D | iio_configfs.rst | 102 That attribute sets the polling frequency in Hz, with mHz precision.
|
/openbmc/linux/Documentation/devicetree/bindings/sound/ |
H A D | nuvoton,nau8821.yaml | 88 description: DMIC clock speed expected value. Unit is Hz.
|
/openbmc/linux/Documentation/devicetree/bindings/timer/ |
H A D | arm,arch_timer_mmio.yaml | 38 description: The frequency of the main counter, in Hz. Should be present
|
/openbmc/linux/Documentation/devicetree/bindings/watchdog/ |
H A D | qcom-wdt.yaml | 66 The frequency of the general purpose timer in Hz.
|
/openbmc/linux/Documentation/devicetree/bindings/media/ |
H A D | samsung,exynos4210-csis.yaml | 47 The IP's main (system bus) clock frequency in Hz.
|
/openbmc/linux/Documentation/devicetree/bindings/rtc/ |
H A D | allwinner,sun6i-a31-rtc.yaml | 143 - description: External 32768 Hz oscillator
|
/openbmc/linux/arch/arm/boot/dts/marvell/ |
H A D | pxa168.dtsi | 149 interrupt-names = "rtc 1Hz", "rtc alarm";
|
H A D | pxa910.dtsi | 159 interrupt-names = "rtc 1Hz", "rtc alarm";
|
/openbmc/linux/Documentation/fb/ |
H A D | matroxfb.rst | 294 maxclk:X maximum dotclock. X can be specified in MHz, kHz or Hz. Default is 297 in kHz or Hz. Default is `don't care`. 298 fv:X maximum vertical frequency. X must be specified in Hz. Default is 299 70 for modes derived from `vesa` with yres <= 400, 60Hz for 364 It is time to redraw whole screen 1000 times in 1024x768, 60Hz. It is
|
/openbmc/linux/Documentation/admin-guide/media/ |
H A D | vivid.rst | 325 framerate of 59.94 Hz is really different from 60 Hz. If the framerate 358 visible. For 50 Hz standards the top field is the oldest and the bottom field 359 is the newest in time. For 60 Hz standards that is reversed: the bottom field 363 contain the top field for 50 Hz standards and the bottom field for 60 Hz 485 cases the driver will generate valid VBI data: for 60 Hz standards it will 488 The XDS stream will give the current time once a minute. For 50 Hz standards 504 for 50 Hz standards and Closed Captioning + XDS for 60 Hz standards. 1164 So it is not possible to loop a 50 Hz (720x576) S-Video output to a 60 Hz 1196 for either raw or sliced VBI. Note that at the moment only CC/XDS (60 Hz formats) 1197 and WSS (50 Hz formats) VBI data is looped. Teletext VBI data is not looped.
|
/openbmc/linux/Documentation/networking/device_drivers/atm/ |
H A D | cxacru.rst | 54 * transmitter_power (dBm/Hz)
|
/openbmc/linux/Documentation/devicetree/bindings/net/ |
H A D | mdio.yaml | 51 Desired MDIO bus clock frequency in Hz. Values greater than IEEE 802.3
|
/openbmc/linux/Documentation/devicetree/bindings/display/bridge/ |
H A D | ite,it6505.yaml | 73 description: Allowed max link frequencies in Hz
|
/openbmc/linux/Documentation/ABI/testing/ |
H A D | sysfs-bus-iio-dac-ltc2688 | 37 Sets the dither signal frequency. Units are in Hz.
|
/openbmc/linux/arch/arm64/boot/dts/freescale/ |
H A D | imx93-tqma9352.dtsi | 72 * IMX93_CLK_SYS_PLL_PFD1 @ 800.000.000 Hz helps to
|