| /openbmc/linux/Documentation/driver-api/tty/ |
| H A D | tty_ldisc.rst | 19 structure. At the point of registration the discipline must be ready to use and
|
| /openbmc/linux/Documentation/devicetree/bindings/net/dsa/ |
| H A D | nxp,sja1105.yaml | 11 least one half of t_CLK. At an SPI frequency of 1MHz, this means a minimum
|
| /openbmc/linux/Documentation/driver-api/ |
| H A D | io-mapping.rst | 89 At driver close time, the io_mapping object must be freed::
|
| H A D | mailbox.rst | 125 /* At this point 'sp' has been sent */
|
| /openbmc/linux/Documentation/driver-api/mtd/ |
| H A D | spi-intel.rst | 29 [1]. At the time writing this the latest image is v92.
|
| /openbmc/linux/Documentation/scsi/ |
| H A D | lpfc.rst | 71 At this time, the driver requires the 2.6.12 (if pre-release, 2.6.12-rc1)
|
| /openbmc/u-boot/doc/ |
| H A D | README.console | 13 At system startup U-Boot initializes a serial console. When U-Boot
|
| /openbmc/linux/Documentation/firmware-guide/acpi/ |
| H A D | debug.rst | 20 you're interested in. At boot-time, use the acpi.debug_layer and
|
| /openbmc/qemu/qapi/ |
| H A D | qdev.json | 123 # the guest. At this point, it's safe to reuse the specified device
|
| /openbmc/linux/Documentation/admin-guide/media/ |
| H A D | pci-cardlist.rst | 41 At the above example, the first card uses the ``saa7134`` driver, and
|
| /openbmc/openbmc-test-automation/redfish/systems/ |
| H A D | test_powersubsystem_settings.robot | 53 Verify Allowable Power Mode Settings Switch At Runtime
|
| /openbmc/qemu/target/hexagon/ |
| H A D | README | 297 At the call to gen_start_packet for a given PC (note that the line number
304 At the start of execution of a packet for a given PC
306 At the end of execution of a packet for a given PC
|
| /openbmc/qemu/docs/devel/ |
| H A D | s390-dasd-ipl.rst | 33 loads the operating system from disk. At the end of this step all or some of
35 control over to the guest operating system. At this point the guest
|
| /openbmc/docs/designs/ |
| H A D | target-fail-monitoring.md | 17 At a high level, systemd is composed of units. For OpenBMC, the two key unit
30 very critical. At a minimum, need to ensure the user of the system is informed
|
| /openbmc/linux/Documentation/trace/coresight/ |
| H A D | coresight-cpu-debug.rst | 36 - At the time this documentation was written, the debug driver mainly relies on
156 At the runtime you can disable idle states with below methods:
|
| /openbmc/linux/Documentation/arch/arm/ |
| H A D | arm.rst | 135 slowly). At the moment they will only work off the controllers on an
196 controlled at runtime by passing the device tree blob to the kernel. At
|
| /openbmc/linux/Documentation/input/devices/ |
| H A D | walkera0701.rst | 19 At back side of transmitter S-video connector can be found. Modulation
|
| /openbmc/qemu/tests/qemu-iotests/ |
| H A D | 178.out.raw | 7 qemu-img: At most one filename argument is allowed.
|
| /openbmc/openbmc-test-automation/lib/ |
| H A D | bios_attr_utils.robot | 126 ... Is Boot Progress At Any State
|
| /openbmc/linux/Documentation/dev-tools/kunit/ |
| H A D | index.rst | 81 - Arrange inputs and targets: At the start of the test, arrange the data
|
| /openbmc/linux/Documentation/userspace-api/media/v4l/ |
| H A D | dev-sdr.rst | 37 At least one of the read/write or streaming I/O methods
|
| H A D | dev-output.rst | 31 (``V4L2_CAP_VBI_OUTPUT``) interface. At least one of the read/write or
|
| /openbmc/linux/arch/arm64/boot/dts/renesas/ |
| H A D | gmsl-cameras.dtsi | 47 #error "At least one camera should be selected"
|
| /openbmc/openbmc/meta-arm/meta-arm/recipes-bsp/trusted-firmware-m/ |
| H A D | trusted-firmware-m.inc | 25 # At present, TF-M Select other GNU Arm compiler versions instead of 11.2:
|
| /openbmc/linux/Documentation/fb/ |
| H A D | ep93xx-fb.rst | 126 At least on the EP9315 there is a silicon bug which causes bit 27 of
|