Searched hist:cc62383f (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/drivers/pinctrl/sunxi/ |
| H A D | pinctrl-sun50i-h6.c | cc62383f Sat Apr 13 11:54:13 CDT 2019 Ondrej Jirman <megous@megous.com> pinctrl: sunxi: Support I/O bias voltage setting on H6
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cc62383f Sat Apr 13 11:54:13 CDT 2019 Ondrej Jirman <megous@megous.com> pinctrl: sunxi: Support I/O bias voltage setting on H6
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| H A D | pinctrl-sunxi.h | cc62383f Sat Apr 13 11:54:13 CDT 2019 Ondrej Jirman <megous@megous.com> pinctrl: sunxi: Support I/O bias voltage setting on H6
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cc62383f Sat Apr 13 11:54:13 CDT 2019 Ondrej Jirman <megous@megous.com> pinctrl: sunxi: Support I/O bias voltage setting on H6
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|
| H A D | pinctrl-sunxi.c | cc62383f Sat Apr 13 11:54:13 CDT 2019 Ondrej Jirman <megous@megous.com> pinctrl: sunxi: Support I/O bias voltage setting on H6
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
cc62383f Sat Apr 13 11:54:13 CDT 2019 Ondrej Jirman <megous@megous.com> pinctrl: sunxi: Support I/O bias voltage setting on H6
H6 SoC has a "pio group withstand voltage mode" register (datasheet
description), that needs to be used to select either 1.8V or 3.3V I/O mode,
based on what voltage is powering the respective pin banks and is thus used
for I/O signals.
Add support for configuring this register according to the voltage of the
pin bank regulator (if enabled).
This is similar to the support for I/O bias voltage setting patch for A80
and the same concerns apply. See:
commit 402bfb3c1352 ("Support I/O bias voltage setting on A80")
Signed-off-by: Ondrej Jirman <megous@megous.com>
Acked-by: Maxime Ripard <maxime.ripard@bootlin.com>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
|