Searched hist:"58109 df6" (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/drivers/net/wireless/ath/ath6kl/ |
| H A D | txrx.c | 58109df6 Tue Sep 11 01:37:00 CDT 2012 Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> ath6kl: Fix reconnection issue after recovery
Disallowing any wmi commands while re-initializing the
firmware results in connection failures after recovery
is done in open/WEP mode. To fix this, clear WMI_READY,
to make sure no wmi command is tried while fw is down.
Remove ATH6KL_STATE_RECOVERY state check in ath6kl_control_tx()
so that any configuration during fw init time will go through
using wmi commands.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
58109df6 Tue Sep 11 01:37:00 CDT 2012 Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> ath6kl: Fix reconnection issue after recovery
Disallowing any wmi commands while re-initializing the
firmware results in connection failures after recovery
is done in open/WEP mode. To fix this, clear WMI_READY,
to make sure no wmi command is tried while fw is down.
Remove ATH6KL_STATE_RECOVERY state check in ath6kl_control_tx()
so that any configuration during fw init time will go through
using wmi commands.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
| H A D | init.c | 58109df6 Tue Sep 11 01:37:00 CDT 2012 Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> ath6kl: Fix reconnection issue after recovery
Disallowing any wmi commands while re-initializing the
firmware results in connection failures after recovery
is done in open/WEP mode. To fix this, clear WMI_READY,
to make sure no wmi command is tried while fw is down.
Remove ATH6KL_STATE_RECOVERY state check in ath6kl_control_tx()
so that any configuration during fw init time will go through
using wmi commands.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
58109df6 Tue Sep 11 01:37:00 CDT 2012 Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> ath6kl: Fix reconnection issue after recovery
Disallowing any wmi commands while re-initializing the
firmware results in connection failures after recovery
is done in open/WEP mode. To fix this, clear WMI_READY,
to make sure no wmi command is tried while fw is down.
Remove ATH6KL_STATE_RECOVERY state check in ath6kl_control_tx()
so that any configuration during fw init time will go through
using wmi commands.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|
| H A D | cfg80211.c | 58109df6 Tue Sep 11 01:37:00 CDT 2012 Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> ath6kl: Fix reconnection issue after recovery
Disallowing any wmi commands while re-initializing the
firmware results in connection failures after recovery
is done in open/WEP mode. To fix this, clear WMI_READY,
to make sure no wmi command is tried while fw is down.
Remove ATH6KL_STATE_RECOVERY state check in ath6kl_control_tx()
so that any configuration during fw init time will go through
using wmi commands.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
58109df6 Tue Sep 11 01:37:00 CDT 2012 Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com> ath6kl: Fix reconnection issue after recovery
Disallowing any wmi commands while re-initializing the
firmware results in connection failures after recovery
is done in open/WEP mode. To fix this, clear WMI_READY,
to make sure no wmi command is tried while fw is down.
Remove ATH6KL_STATE_RECOVERY state check in ath6kl_control_tx()
so that any configuration during fw init time will go through
using wmi commands.
Signed-off-by: Vasanthakumar Thiagarajan <vthiagar@qca.qualcomm.com>
Signed-off-by: Kalle Valo <kvalo@qca.qualcomm.com>
|