Searched hist:"4 c52783b3d024e153c4972b97332e314bc3bdc46" (Results 1 – 3 of 3) sorted by relevance
/openbmc/u-boot/drivers/ |
H A D | Makefile | 4c52783b3d024e153c4972b97332e314bc3bdc46 Thu Nov 02 04:49:51 CST 2006 roy zang <tie-fei.zang@freescale.com> General code modification for mpc7448hpc2 board support. 1. Add 7447A and 7448 processor support. 2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically (such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan the slots, if there is no pci card, the tsi108/9 will cause a machine check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
/openbmc/u-boot/ |
H A D | README | 4c52783b3d024e153c4972b97332e314bc3bdc46 Thu Nov 02 04:49:51 CST 2006 roy zang <tie-fei.zang@freescale.com> General code modification for mpc7448hpc2 board support. 1. Add 7447A and 7448 processor support. 2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically (such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan the slots, if there is no pci card, the tsi108/9 will cause a machine check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|
H A D | Makefile | 4c52783b3d024e153c4972b97332e314bc3bdc46 Thu Nov 02 04:49:51 CST 2006 roy zang <tie-fei.zang@freescale.com> General code modification for mpc7448hpc2 board support. 1. Add 7447A and 7448 processor support. 2. Add the following flags.
CFG_CONFIG_BUS_CLK : If the 74xx bus frequency can be configured dynamically (such as by switch on board), this flag should be set.
CFG_EXCEPTION_AFTER_RELOCATE: If an exception occurs after the u-boot relocates to RAM, this flag should be set.
CFG_SERIAL_HANG_IN_EXCEPTION: If the print out function will cause the system hang in exception, this flag should be set.
There is a design issue for tsi108/109 pci configure read. When pci scan the slots, if there is no pci card, the tsi108/9 will cause a machine check exception for mpc7448 processor.
Signed-off-by: Alexandre Bounine <alexandreb@tundra.com> Signed-off-by: Roy Zang <tie-fei.zang@freescale.com>
|