Searched hist:"1069 a0bb" (Results 1 – 3 of 3) sorted by relevance
| /openbmc/linux/arch/arm64/boot/dts/freescale/ |
| H A D | fsl-ls1043a-qds.dts | 1069a0bb Tue Jul 07 02:40:31 CDT 2020 Ran Wang <ran.wang_1@nxp.com> arm64: dts: ls1043a: update USB nodes status to match board config
ls1043a-rdb and ls1043a-qds board’s default HW config (such as
pin mux selection) would not enable some USB controllers’
data path, which causing over-current detected on those
controllers. This will hit the case of ‘xhci driver prevent bus suspend
if a root hub port detected over-current condition’, causing system
failed to be suspended. So disable them in device tree to resolve this
issue.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1069a0bb Tue Jul 07 02:40:31 CDT 2020 Ran Wang <ran.wang_1@nxp.com> arm64: dts: ls1043a: update USB nodes status to match board config
ls1043a-rdb and ls1043a-qds board’s default HW config (such as
pin mux selection) would not enable some USB controllers’
data path, which causing over-current detected on those
controllers. This will hit the case of ‘xhci driver prevent bus suspend
if a root hub port detected over-current condition’, causing system
failed to be suspended. So disable them in device tree to resolve this
issue.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| H A D | fsl-ls1043a-rdb.dts | 1069a0bb Tue Jul 07 02:40:31 CDT 2020 Ran Wang <ran.wang_1@nxp.com> arm64: dts: ls1043a: update USB nodes status to match board config
ls1043a-rdb and ls1043a-qds board’s default HW config (such as
pin mux selection) would not enable some USB controllers’
data path, which causing over-current detected on those
controllers. This will hit the case of ‘xhci driver prevent bus suspend
if a root hub port detected over-current condition’, causing system
failed to be suspended. So disable them in device tree to resolve this
issue.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1069a0bb Tue Jul 07 02:40:31 CDT 2020 Ran Wang <ran.wang_1@nxp.com> arm64: dts: ls1043a: update USB nodes status to match board config
ls1043a-rdb and ls1043a-qds board’s default HW config (such as
pin mux selection) would not enable some USB controllers’
data path, which causing over-current detected on those
controllers. This will hit the case of ‘xhci driver prevent bus suspend
if a root hub port detected over-current condition’, causing system
failed to be suspended. So disable them in device tree to resolve this
issue.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|
| H A D | fsl-ls1043a.dtsi | 1069a0bb Tue Jul 07 02:40:31 CDT 2020 Ran Wang <ran.wang_1@nxp.com> arm64: dts: ls1043a: update USB nodes status to match board config
ls1043a-rdb and ls1043a-qds board’s default HW config (such as
pin mux selection) would not enable some USB controllers’
data path, which causing over-current detected on those
controllers. This will hit the case of ‘xhci driver prevent bus suspend
if a root hub port detected over-current condition’, causing system
failed to be suspended. So disable them in device tree to resolve this
issue.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
1069a0bb Tue Jul 07 02:40:31 CDT 2020 Ran Wang <ran.wang_1@nxp.com> arm64: dts: ls1043a: update USB nodes status to match board config
ls1043a-rdb and ls1043a-qds board’s default HW config (such as
pin mux selection) would not enable some USB controllers’
data path, which causing over-current detected on those
controllers. This will hit the case of ‘xhci driver prevent bus suspend
if a root hub port detected over-current condition’, causing system
failed to be suspended. So disable them in device tree to resolve this
issue.
Signed-off-by: Ran Wang <ran.wang_1@nxp.com>
Signed-off-by: Shawn Guo <shawnguo@kernel.org>
|