| /openbmc/linux/Documentation/devicetree/bindings/leds/ |
| H A D | richtek,rt8515.yaml | 15 current for each mode is defined in hardware using two resistors
34 resistors limits the maximum flash current. This must be set
43 resistors limits the maximum torch current. This must be set
|
| /openbmc/linux/drivers/rtc/ |
| H A D | rtc-ds1343.c | 147 char *diodes = "disabled", *resistors = " "; in ds1343_show_tricklecharger() local
166 resistors = "1k Ohm"; in ds1343_show_tricklecharger()
170 resistors = "2k Ohm"; in ds1343_show_tricklecharger()
174 resistors = "4k Ohm"; in ds1343_show_tricklecharger()
183 return sprintf(buf, "%s %s\n", diodes, resistors); in ds1343_show_tricklecharger()
|
| H A D | rtc-ds1305.c | 386 char *resistors = ""; in ds1305_proc() local
402 resistors = "2k Ohm"; in ds1305_proc()
405 resistors = "4k Ohm"; in ds1305_proc()
408 resistors = "8k Ohm"; in ds1305_proc()
417 seq_printf(seq, "trickle_charge\t: %s%s\n", diodes, resistors); in ds1305_proc()
|
| /openbmc/linux/Documentation/hwmon/ |
| H A D | ina3221.rst | 48 value for their shunt resistors)
53 value for their shunt resistors)
|
| H A D | w83l785ts.rst | 25 of external resistors, so the user cannot change it. Values seen so
|
| H A D | ltc4260.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| H A D | ltc4261.rst | 44 registers. If a set of voltage divider resistors is installed, calculate the
|
| /openbmc/linux/drivers/gpu/drm/nouveau/nvkm/subdev/bios/ |
| H A D | iccsense.c | 122 rail->resistors[r].mohm = nvbios_rd08(bios, entry + res_start + r * 2); in nvbios_iccsense_parse()
123 rail->resistors[r].enabled = !(nvbios_rd08(bios, entry + res_start + r * 2 + 1) & 0x40); in nvbios_iccsense_parse()
|
| /openbmc/linux/Documentation/devicetree/bindings/hwmon/ |
| H A D | ntc-thermistor.yaml | 12 Thermistors with negative temperature coefficient (NTC) are resistors that
59 We can use both pull-up and pull-down resistors at the same time, and then
|
| /openbmc/linux/drivers/gpu/drm/nouveau/include/nvkm/subdev/bios/ |
| H A D | iccsense.h | 13 struct pwr_rail_resistor_t resistors[3]; member
|
| /openbmc/linux/drivers/input/serio/ |
| H A D | parkbd.c | 33 * The diodes can be fairly any type, and the resistors should be somewhere
34 * around 5 kOhm, but the adapter will likely work without the resistors,
|
| /openbmc/linux/include/linux/platform_data/ |
| H A D | st_sensors_pdata.h | 21 * @pullups: enable/disable i2c controller pullup resistors.
|
| /openbmc/linux/Documentation/devicetree/bindings/pinctrl/ |
| H A D | mediatek,mt6779-pinctrl.yaml | 162 Pull up settings for 2 pull resistors, R0 and R1. User can
174 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt6795-pinctrl.yaml | 133 Pull up settings for 2 pull resistors, R0 and R1. User can
145 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt8183-pinctrl.yaml | 146 Pull up settings for 2 pull resistors, R0 and R1. User can
158 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| H A D | mediatek,mt8365-pinctrl.yaml | 152 Pull up settings for 2 pull resistors, R0 and R1. User can
166 Pull down settings for 2 pull resistors, R0 and R1. User can
|
| /openbmc/linux/Documentation/devicetree/bindings/net/ |
| H A D | motorcomm,yt8xxx.yaml | 59 be configured with hardware pull-up resistors to match the SOC voltage
76 be configured with hardware pull-up resistors to match the SOC voltage
|
| /openbmc/linux/include/linux/usb/ |
| H A D | isp116x.h | 11 /* Enable internal resistors on downstream ports */
|
| H A D | isp1362.h | 11 /* Enable internal pulldown resistors on downstream ports */
|
| /openbmc/linux/Documentation/devicetree/bindings/gpio/ |
| H A D | gpio-xra1403.txt | 5 - Internal pull-up resistors
|
| /openbmc/linux/arch/sh/drivers/pci/ |
| H A D | fixups-sdk7786.c | 21 * resistors to determine card presence. Hotplug remains unsupported.
|
| /openbmc/linux/Documentation/devicetree/bindings/power/supply/ |
| H A D | richtek,rt9467.yaml | 18 integrated sensing resistors.
|
| /openbmc/linux/Documentation/ABI/stable/ |
| H A D | sysfs-class-udc | 63 Allows users to disconnect data pullup resistors thus causing a
|
| /openbmc/linux/Documentation/devicetree/bindings/iio/imu/ |
| H A D | st,lsm6dsx.yaml | 78 description: enable/disable internal i2c controller pullup resistors.
|
| /openbmc/linux/Documentation/networking/device_drivers/can/ |
| H A D | can327.rst | 326 Your adapter may have resistors soldered in which are meant to terminate
331 termination resistors on its PCB and try removing them.
|