| /openbmc/linux/Documentation/devicetree/bindings/net/ |
| H A D | mediatek-dwmac.yaml | 112 1. tx clock will be inversed in MII/RGMII case,
113 2. tx clock inside MAC will be inversed relative to reference clock
115 3. the reference clock, which outputs to TXC pin will be inversed in RMII case
122 1. rx clock will be inversed in MII/RGMII case.
123 2. reference clock will be inversed when arrived at MAC in RMII case, when
125 3. the inside clock, which be sent to MAC, will be inversed in RMII case when
|
| H A D | mediatek,star-emac.yaml | 60 If present, indicates that clock on RXC pad will be inversed.
65 If present, indicates that clock on TXC pad will be inversed.
|
| /openbmc/linux/include/uapi/linux/netfilter_bridge/ |
| H A D | ebt_vlan.h | 19 __u8 invflags; /* Inverse bitmask bit 1=1 - inversed ID arg,
20 bit 2=1 - inversed Pirority arg */
|
| /openbmc/linux/drivers/platform/x86/ |
| H A D | mlx-platform.c | 781 .inversed = 1,
790 .inversed = 0,
799 .inversed = 1,
808 .inversed = 0,
820 .inversed = 1,
829 .inversed = 0,
838 .inversed = 1,
847 .inversed = 0,
869 .inversed = 1,
878 .inversed = 0,
[all …]
|
| /openbmc/linux/Documentation/devicetree/bindings/leds/ |
| H A D | leds-el15203000.txt | 19 - inversed cascade pattern
21 - inversed bounce pattern
|
| /openbmc/linux/include/linux/platform_data/ |
| H A D | mlxreg.h | 168 * @inversed: if 0: 0 for signal status is OK, if 1 - 1 is OK;
181 u8 inversed; member
|
| /openbmc/linux/drivers/platform/mellanox/ |
| H A D | mlxreg-hotplug.c | 228 /* Bit = 0 : functional if item->inversed is true. */ in mlxreg_hotplug_attr_show()
229 if (item->inversed) in mlxreg_hotplug_attr_show()
389 if (item->inversed) in mlxreg_hotplug_work_helper()
394 if (item->inversed) in mlxreg_hotplug_work_helper()
634 if (item->inversed) { in mlxreg_hotplug_set_irq()
|
| H A D | nvsw-sn2201.c | 485 .inversed = 1,
494 .inversed = 0,
503 .inversed = 1,
512 .inversed = 1,
|
| /openbmc/linux/Documentation/driver-api/ |
| H A D | pwm.rst | 120 enabled. Value is the string "normal" or "inversed".
146 goes low for the remainder of the period. Conversely, a signal with inversed
|
| /openbmc/linux/Documentation/ABI/testing/ |
| H A D | sysfs-class-pwm | 70 "inversed".
|
| /openbmc/linux/drivers/media/platform/samsung/s5p-g2d/ |
| H A D | g2d-hw.c | 88 /* inversed scaling factor: src is numerator */ in g2d_set_v41_stretch()
|
| /openbmc/linux/drivers/regulator/ |
| H A D | pwm-regulator.c | 167 * This is happening when the user needs an inversed polarity, but the in pwm_regulator_get_voltage()
203 * This is happening when the user needs an inversed polarity, but the in pwm_regulator_set_voltage()
|
| /openbmc/u-boot/drivers/timer/ |
| H A D | timer-uclass.c | 22 * the value should be inversed inside the method. There may be no real
|
| /openbmc/u-boot/include/configs/ |
| H A D | cm_t335.h | 132 /* Status LED polarity is inversed, so init it in the "off" state */
|
| /openbmc/linux/drivers/pwm/ |
| H A D | sysfs.c | 170 polarity = "inversed"; in polarity_show()
189 else if (sysfs_streq(buf, "inversed")) in polarity_store()
|
| H A D | pwm-imx-tpm.c | 266 * ELS[1:0] = 2b01 yields inversed polarity. in pwm_imx_tpm_apply_hw()
|
| /openbmc/linux/drivers/media/dvb-frontends/ |
| H A D | bcm3510_priv.h | 347 u8 QRE :1; /* if QSE and the spectrum is inversed */
|
| /openbmc/linux/drivers/pinctrl/bcm/ |
| H A D | pinctrl-bcm281xx.c | 1157 /* inversed since register is for input _disable_ */ in bcm281xx_std_pin_update()
1259 /* inversed since register is for input _disable_ */ in bcm281xx_i2c_pin_update()
1304 /* inversed since register is for input _disable_ */ in bcm281xx_hdmi_pin_update()
|
| /openbmc/linux/sound/soc/codecs/ |
| H A D | jz4770.c | 344 * NOTE: DACR/DACL are inversed; the gain value written to DACR
365 /* HPR/HPL inversed for the same reason as above */
|
| /openbmc/u-boot/board/toradex/colibri_imx7/ |
| H A D | colibri_imx7.c | 145 /* Set PWM<A> to full brightness (assuming inversed polarity) */ in setup_lcd()
|
| /openbmc/u-boot/board/toradex/colibri-imx6ull/ |
| H A D | colibri-imx6ull.c | 162 /* Set PWM<A> to full brightness (assuming inversed polarity) */ in setup_lcd()
|
| /openbmc/linux/arch/arm/mach-omap2/ |
| H A D | board-n8x0.c | 346 /* All slot pin bits seem to be inversed until first switch change */ in n8x0_mmc_late_init()
|
| /openbmc/linux/drivers/media/pci/zoran/ |
| H A D | zr36016.c | 234 * (blue faces, etc., cr/cb inversed). There's probably in zr36016_set_video()
|
| /openbmc/linux/drivers/media/pci/tw5864/ |
| H A D | tw5864-reg.h | 1782 * 0 Not inversed (Default)
1783 * 1 Inversed
1788 * 0 Not inversed (Default)
1789 * 1 Inversed
|
| /openbmc/linux/sound/soc/intel/catpt/ |
| H A D | dsp.c | 436 /* generate int deassert msg to fix inversed int logic */ in catpt_dsp_power_up()
|