Searched full:wdog_b (Results 1 – 12 of 12) sorted by relevance
| /openbmc/linux/Documentation/devicetree/bindings/regulator/ |
| H A D | nxp,pca9450-regulator.yaml | 89 nxp,wdog_b-warm-reset:
92 When WDOG_B signal is asserted a warm reset will be done instead of cold
|
| /openbmc/u-boot/arch/arm/mach-imx/imx8m/ |
| H A D | soc.c | 63 * Output WDOG_B signal to reset external pmic or POR_B decided by in set_wdog_reset()
234 /* Clear WDA to trigger WDOG_B immediately */ in reset_cpu()
|
| /openbmc/linux/Documentation/devicetree/bindings/watchdog/ |
| H A D | fsl-imx-wdt.yaml | 53 external reset (WDOG_B) instead of issuing a software reset.
|
| /openbmc/linux/drivers/regulator/ |
| H A D | pca9450-regulator.c | 812 if (of_property_read_bool(i2c->dev.of_node, "nxp,wdog_b-warm-reset")) in pca9450_i2c_probe()
817 /* Set reset behavior on assertion of WDOG_B signal */ in pca9450_i2c_probe()
821 dev_err(&i2c->dev, "Failed to set WDOG_B reset behavior\n"); in pca9450_i2c_probe()
|
| /openbmc/u-boot/board/freescale/mx6sxsabresd/ |
| H A D | mx6sxsabresd.c | 279 * Because kernel set WDOG_B mux before pad with the common pinctrl in board_init()
280 * framwork now and wdog reset will be triggered once set WDOG_B mux in board_init()
|
| /openbmc/linux/drivers/watchdog/ |
| H A D | imx2_wdt.c | 39 #define IMX2_WDT_WCR_WDA BIT(5) /* -> External Reset WDOG_B */
147 /* Or if external-reset assert WDOG_B reset only on time-out */ in imx2_wdt_setup()
|
| /openbmc/u-boot/board/udoo/neo/ |
| H A D | neo.c | 336 * Because kernel set WDOG_B mux before pad with the commone pinctrl in board_init()
337 * framwork now and wdog reset will be triggered once set WDOG_B mux in board_init()
|
| /openbmc/u-boot/board/compulab/cl-som-imx7/ |
| H A D | cl-som-imx7.c | 296 * - Output WDOG_B signal to reset external pmic.
|
| /openbmc/linux/arch/arm64/boot/dts/freescale/ |
| H A D | imx8mm-data-modul-edm-sbc.dts | 210 "", "ENET_RST#", "WDOG_B#", "PMIC_INT#",
885 /* WDOG_B# */
|
| H A D | imx8mp-data-modul-edm-sbc.dts | 234 "", "USBHUB_RESET#", "WDOG_B#", "PMIC_INT#",
969 /* WDOG_B# */
|
| /openbmc/u-boot/arch/arm/dts/ |
| H A D | imx6ull-14x14-evk.dts | 526 fsl,wdog_b;
|
| /openbmc/u-boot/arch/arm/mach-imx/mx7/ |
| H A D | soc.c | 347 * Output WDOG_B signal to reset external pmic or POR_B decided by in set_wdog_reset()
|