Home
last modified time | relevance | path

Searched full:vsc9953 (Results 1 – 16 of 16) sorted by relevance

/openbmc/u-boot/include/
H A Dvsc9953.h5 * Driver for the Vitesse VSC9953 L2 Switch
264 /* VSC9953 ANA structure */
371 /* END VSC9953 ANA structure t*/
373 /* VSC9953 DEV_GMII structure */
400 /* END VSC9953 DEV_GMII structure */
402 /* VSC9953 QSYS structure */
462 /* END VSC9953 QSYS structure */
464 /* VSC9953 SYS structure */
608 /* END VSC9953 SYS structure */
610 /* VSC9953 REW structure */
[all …]
/openbmc/u-boot/drivers/net/
H A Dvsc9953.c5 * Driver for the Vitesse VSC9953 L2 Switch
15 #include <vsc9953.h>
330 /* Get PVID of a VSC9953 port */
353 /* Set PVID for a VSC9953 port */
391 /* Enable/disable vlan aware of a VSC9953 port */
413 /* Set all VSC9953 ports' vlan aware */
422 /* Enable/disable vlan pop count of a VSC9953 port */
448 /* Set all VSC9953 ports' pop count */
512 /* Egress untag modes of a VSC9953 port */
521 /* Get egress tagging configuration for a VSC9953 port */
[all …]
H A DMakefile71 obj-$(CONFIG_VSC9953) += vsc9953.o
/openbmc/linux/Documentation/devicetree/bindings/net/dsa/
H A Dmscc,ocelot.yaml24 VSC9953 (Seville):
60 - mscc,vsc9953-switch
164 # Seville VSC9953 (NXP T1040)
171 compatible = "mscc,vsc9953-switch";
/openbmc/u-boot/doc/
H A DREADME.t1040-l2switch1 This file contains information for VSC9953, a Vitesse L2 Switch IP
6 VSC9953 is an 8-port Gigabit Ethernet switch supports the following features:
/openbmc/linux/drivers/net/dsa/ocelot/
H A DKconfig63 This driver supports the VSC9953 (Seville) switch, which is embedded
H A Dseville_vsc9953.c2 /* Distributed Switch Architecture VSC9953 driver
895 rc = mscc_miim_setup(dev, &bus, "VSC9953 internal MDIO bus", in vsc9953_mdio_bus_alloc()
1060 { .compatible = "mscc,vsc9953-switch" },
/openbmc/u-boot/board/freescale/t104xrdb/
H A Deth.c14 #include <vsc9953.h>
/openbmc/linux/net/dsa/
H A DKconfig106 (VSC7511, VSC7512, VSC7513, VSC7514, VSC9953, VSC9959). In this mode,
/openbmc/u-boot/arch/powerpc/cpu/mpc8xxx/
H A Dcpu.c18 #include <vsc9953.h>
/openbmc/u-boot/board/freescale/t1040qds/
H A Deth.c20 #include <vsc9953.h>
/openbmc/u-boot/include/configs/
H A DT1040QDS.h587 /* Enable VSC9953 L2 Switch driver */
H A DT104xRDB.h705 /* Enable VSC9953 L2 Switch driver on T1040 SoC */
/openbmc/linux/arch/powerpc/boot/dts/fsl/
H A Dt1040si-post.dtsi633 compatible = "mscc,vsc9953-switch";
/openbmc/u-boot/cmd/
H A DKconfig1352 by the vsc9953 Ethernet driver at present. Sub-commands allow
/openbmc/linux/
H A Dopengrok0.0.log3435 2024-12-28 20:09:06.570-0600 FINEST t1092 PendingFileCompleter.doRename: Moved pending as file: '/opengrok/data/xref/openbmc/u-boot/include/vsc9953.h.gz'
[all...]