Merge git://git.denx.de/u-boot-tegra

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initializat

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initialization and cpuinfo handling

zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING

zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation

mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode

nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params

scsi:
- convert ceva sata to UCLASS_AHCI

timer:
- Add Cadence TTC for ZynqMP r5

watchdog:
- Minor cadence driver cleanup

show more ...

Merge git://git.denx.de/u-boot-fsl-qoriq

Merge git://git.denx.de/u-boot-socfpga

SPDX: Convert a few files that were missed before

As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and

SPDX: Convert a few files that were missed before

As part of the main conversion a few files were missed. These files had
additional whitespace after the '*' and before the SPDX tag and my
previous regex was too strict. This time I did a grep for all SPDX tags
and then filtered out anything that matched the correct styles.

Fixes: 83d290c56fab ("SPDX: Convert all of our single license tags to Linux Kernel style")
Reported-by: Heinrich Schuchardt <xypron.debian@gmx.de>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes

show more ...

Merge git://git.denx.de/u-boot-sunxi

Merge git://git.denx.de/u-boot-spi

Merge branch 'master' of git://git.denx.de/u-boot-coldfire

Merge git://git.denx.de/u-boot-mmc

Merge git://git.denx.de/u-boot-fsl-qoriq

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

Patch queue for efi - 2018-01-23

This time around we have a lot of EFI patches from Heinrich.
Highlights are:

Merge tag 'signed-efi-next' of git://github.com/agraf/u-boot

Patch queue for efi - 2018-01-23

This time around we have a lot of EFI patches from Heinrich.
Highlights are:

- Allow EFI applications to register as drivers
- Allow exposure of U-Boot block devices from an EFI payload
- Compatibility improvements

show more ...

efi_driver: EFI block driver

This patch provides
* a uclass for EFI drivers
* a EFI driver for block devices

For each EFI driver the uclass
* creates a handle
* adds

efi_driver: EFI block driver

This patch provides
* a uclass for EFI drivers
* a EFI driver for block devices

For each EFI driver the uclass
* creates a handle
* adds the driver binding protocol

The uclass provides the bind, start, and stop entry points for the driver
binding protocol.

In bind() and stop() it checks if the controller implements the protocol
supported by the EFI driver. In the start() function it calls the bind()
function of the EFI driver. In the stop() function it destroys the child
controllers.

The EFI block driver binds to controllers implementing the block io
protocol.

When the bind function of the EFI block driver is called it creates a
new U-Boot block device. It installs child handles for all partitions and
installs the simple file protocol on these.

The read and write functions of the EFI block driver delegate calls to the
controller that it is bound to.

A usage example is as following:

U-Boot loads the iPXE snp.efi executable. iPXE connects an iSCSI drive and
exposes a handle with the block IO protocol. It calls ConnectController.

Now the EFI block driver installs the partitions with the simple file
protocol.

iPXE uses the simple file protocol to load Grub or the Linux Kernel.

Signed-off-by: Heinrich Schuchardt <xypron.glpk@gmx.de>
[agraf: add comment on calloc len]
Signed-off-by: Alexander Graf <agraf@suse.de>

show more ...