Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch '2019-03-25-master-imports'

- Convert various SPI related options to Kconfig

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig scr

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

show more ...

Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.04-rc2

xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac add

Merge tag 'xilinx-for-v2019.04-rc2' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.04-rc2

xilinx:
- Start to use distro boot commands first
- Setup fdtfile on ZynqMP
- Move mac addr eeprom read to common location
- Convert to OF_SEPARATE
- Switch all board to DM_I2C
- Some DT syncs

i2c:
- Remove !DM_I2C zynq driver

versal:
- Enable some more features
- Add mini configurations

show more ...

ARM: zynq: Run distribution boot commands first

This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BO

ARM: zynq: Run distribution boot commands first

This patch is doing two things.
1. Exchanging order of boot commands. distro_bootcmd is run first
followed by Xilinx boot command.
2. Remove CONFIG_BOOTCOMMAND from configs (and follow mainline) by
creating Xilinx distribution bootcommand and wiring it as the last
bootcommand.

QSPI, NAND distribution boot command will be added later.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-spi

- SPI-NOR support

configs: Don't use SPI_FLASH_BAR as default

Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing

configs: Don't use SPI_FLASH_BAR as default

Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed

show more ...

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulas

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

xilinx: Sync symbols location in defconfigs

CONFIG_DEBUG_UART_BASE and CONFIG_DEBUG_UART_CLOCK have changed that's
why this sync.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Merge tag 'xilinx-for-v2018.07-2' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07 second pull

zynqmp:
- Show reset reason
- Remove emulation platform
- Update pmufw version
-

Merge tag 'xilinx-for-v2018.07-2' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07 second pull

zynqmp:
- Show reset reason
- Remove emulation platform
- Update pmufw version
- Simplify mmc bootmode
- Remove dc2 useless configuration file
- Cleanup mini config
- Defconfig syncup
- zcu100, zcu104 and zcu111 dts fixes

xilinx:
- Use live-tree functions in some drivers
- Add support for Avnet Minized and Antminer S9

fpga:
- Add secure bitstream loading support

mmc:
- Add hs200 mode support

usb xhci:
- Header fix

show more ...

arm: zynq: Add initial support for Avnet MiniZed

Initial support for Avnet MiniZed board. Tested UART1 (serial console),
QSPI(Flash), SDHCI1 (eMMC), USB.

Signed-off-by: Ibai Erkiaga <ibai.erkiaga-e

arm: zynq: Add initial support for Avnet MiniZed

Initial support for Avnet MiniZed board. Tested UART1 (serial console),
QSPI(Flash), SDHCI1 (eMMC), USB.

Signed-off-by: Ibai Erkiaga <ibai.erkiaga-elorza@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...