Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.01

microblaze:
- Use default functions for memory decoding
- Showing model from DT

zynq:
- Fix spi f

Merge tag 'xilinx-for-v2019.01' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2019.01

microblaze:
- Use default functions for memory decoding
- Showing model from DT

zynq:
- Fix spi flash DTs
- Fix zynq_help_text with CONFIG_SYS_LONGHELP
- Tune cse/mini configurations
- Enabling cse/mini testing with current targets

zynqmp:
- Enable gzip SPL support
- Fix chip detection logic
- Tune mini configurations
- DT fixes(spi-flash, models, clocks, etc)
- Add support for OF_SEPARATE configurations
- Enabling mini testing with current targets
- Add mini mtest configuration
- Some minor config setting

nand:
- arasan: Add subpage configuration

net:
- gem: Add 64bit DMA support

show more ...

microblaze: Showing model information from DT by default

Show information about board read from DT by default to know what board
U-Boot is running at.

Signed-off-by: Michal Simek <michal.simek@xili

microblaze: Showing model information from DT by default

Show information about board read from DT by default to know what board
U-Boot is running at.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

configs: Migrate and re-enabled CONFIG_CMD_MTDPARTS

Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand. This exposed that we had
no

configs: Migrate and re-enabled CONFIG_CMD_MTDPARTS

Now that CMD_UBI does not select CMD_MTDPARTS we need to make platforms
that had been enabling it turn it on by hand. This exposed that we had
not yet migrated CMD_MTDPARTS fully, so do so now.

Fixes: 86dfa556d927 ("cmd: ubi: Remove useless call to mtdparts_init()")
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_P

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11-rc2-v2

FPGA:
- Fix SPL fpga loading from FIT

ARM64:
- Fix gic accesses in EL2/EL1

Xilinx:
- Add dlc20 board support
- Add Ver

Merge git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.11-rc2-v2

FPGA:
- Fix SPL fpga loading from FIT

ARM64:
- Fix gic accesses in EL2/EL1

Xilinx:
- Add dlc20 board support
- Add Versal board support
- Sync defconfigs
- Enable MP via Kconfig
- Add missing efuse node
- Enable CDC for zcu100

cmd:
- Fix kgdb Kconfig dependency

show more ...

xilinx: Sync defconfigs with current Kconfig

There are some inconsistencies which should be fixed.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANK

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_MTD_PARTITIONS et al to Kconfig

This converts the following to Kconfig:
CONFIG_MTD_PARTITIONS
CONFIG_MTD_DEVICE

Signed-off-by: Adam Ford <aford173@gmail.com>

Merge tag 'xilinx-for-v2018.09' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.09

clk:
- Fix zynqmp clock driver

common:
- Handle CMD_RET_USAGE in cmd_process_error
- Use return m

Merge tag 'xilinx-for-v2018.09' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.09

clk:
- Fix zynqmp clock driver

common:
- Handle CMD_RET_USAGE in cmd_process_error
- Use return macros in cmd_process_error
- Fix duplication of CONFIG_SYS_PROMPT_HUSH_PS2
- Support watchdog in usb_kbd.c
- Fix name usage in usb_kbd.c
- Support systems with non zero memory start initialized from DT only

gpio:
- Add support for manual relocation in uclass
- zynq - use live tree
- zynq - fix match data reading
- zynq - setup bank name
- xilinx - convert driver to DM

microblaze:
- Use generic iounmap/ioremap implementations
- Redesign reset logic with sysreset features
- Use watchdog and gpio over DM
- Remove unused macros and fix some checkpatch issues
- Fix timer initialization not to be called twice

serial:
- zynq - Use platdata intead of priv data

sysreset:
- Add support for manual relocation in uclass
- Add gpio-restart driver
- Add microblaze soft reset driver

watchdog:
- Add support for aliases in uclass
- Add support for manual relocation in uclass
- Convert xilinx driver to DM
- cadence - update info in the driver and not stop wdt in probe

xilinx:
- Enable LED gpio for some targets with gpio-leds DT node
- Setup variables via Kconfig

zynq:
- Add support for watchdog aliases
- Add support for mini nand/nor configurations
- Wire FPGA initalization in SPL

zynqmp:
- Enable mass storage for zcu100
- Handle external pmufw files
- Add support for secure images
- Some Kconfig movements and alignments
- Add support for watchdog aliases
- Use subcommands style for platform command
- Add mmio_read/write platform commands
- DT updates
- Add support for mini qspi configuration

show more ...

xilinx: Enable led support for some boards

Enable led support for boards which have "gpio-leds" node.
And also for microblaze which is converted to DM_GPIO now.
Tested on zcu100.

Signed-off-by: Mic

xilinx: Enable led support for some boards

Enable led support for boards which have "gpio-leds" node.
And also for microblaze which is converted to DM_GPIO now.
Tested on zcu100.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

microblaze: Convert generic platform to DM gpio

Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support wa

microblaze: Convert generic platform to DM gpio

Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.

GPIO reset is handled via sysreset with adding this fragment to DT.

gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};

hard-reset-gpio property is not documented and also handled.
Conversion is required.

Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

microblaze: Enable watchdog via defconfig

DM watchdog should be enabled by default.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initialization and cpuinfo handling

zynqmp

Merge tag 'xilinx-for-v2018.07' of git://www.denx.de/git/u-boot-microblaze

Xilinx changes for v2018.07

microblaze:
- Align defconfig

zynq:
- Rework fpga initialization and cpuinfo handling

zynqmp:
- Add ZynqMP R5 support
- Wire and enable watchdog on zcu100-revC
- Setup MMU map for DDR at run time
- Show board info based on DT and cleanup IDENT_STRING

zynqmp tools:
- Add read partition support
- Add initial support for Xilinx bif format for boot.bin generation

mmc:
- Fix get_timer usage on 64bit cpus
- Add support for SD3.0 UHS mode

nand-zynq:
- Add support for 16bit buswidth
- Use address cycles from onfi params

scsi:
- convert ceva sata to UCLASS_AHCI

timer:
- Add Cadence TTC for ZynqMP r5

watchdog:
- Minor cadence driver cleanup

show more ...

microblaze: Dont enable UBI support by default

This patch removes UBI support from defconfig and it can
be enabled from menuconfig as per need.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga

microblaze: Dont enable UBI support by default

This patch removes UBI support from defconfig and it can
be enabled from menuconfig as per need.

Signed-off-by: Siva Durga Prasad Paladugu <siva.durga.paladugu@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge tag 'xilinx-for-v2018.05' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.05

- Fix mkimage recognition
- Update all my fragments

ZynqMP:
- Use clk driver
- Support loading el

Merge tag 'xilinx-for-v2018.05' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.05

- Fix mkimage recognition
- Update all my fragments

ZynqMP:
- Use clk driver
- Support loading elfs in el1
- Various DTS and defconfig changes
- Enable newer pmufw versions
- Support more clocks
- Remove ep108
- Secure image support
- Fix memtest setup

Zynq:
- Enabling watchdog driver
- Support more clocks
- defconfig changes

fpga:
- Simplify error path

net:
- GMII case update

show more ...

xilinx: Sync defconfigs with latest Kconfig updates

Make defconfigs up2date with current location.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

Merge tag 'xilinx-kconfig-for-v2018.03' of git://www.denx.de/git/u-boot-microblaze

Xilinx Kconfig changes for v2018.03

- Moving some macros to Kconfig

# gpg: Signature made Thu 01 Mar 2018 10:45:5

Merge tag 'xilinx-kconfig-for-v2018.03' of git://www.denx.de/git/u-boot-microblaze

Xilinx Kconfig changes for v2018.03

- Moving some macros to Kconfig

# gpg: Signature made Thu 01 Mar 2018 10:45:58 AM EST using DSA key ID 294A0C21
# gpg: Good signature from "Michal Simek <monstr@monstr.eu>"
# gpg: aka "Michal Simek (Xilinx) <michals@xilinx.com>"
# gpg: aka "Michal Simek (Xilinx) <michal.simek@xilinx.com>"

show more ...

microblaze: Added Kconfig support for CONFIG_XILINX_GPIO

This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.co

microblaze: Added Kconfig support for CONFIG_XILINX_GPIO

This patch added Kconfig support for CONFIG_XILINX_GPIO
and enabled it in respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Siva Durga Prasad Paladugu <sivadur@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_P

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes

show more ...

microblaze: Moved ethernet PHY configs of Microblaze board to defconfig

This patch moved ethernet PHY configs of Microblaze board to
respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.

microblaze: Moved ethernet PHY configs of Microblaze board to defconfig

This patch moved ethernet PHY configs of Microblaze board to
respective defconfig.

Signed-off-by: Vipul Kumar <vipulk@xilinx.com>
Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

env: Allow to build multiple environments in Kconfig

Now that we have everything in place in the code, let's allow to build
multiple environments backend through Kconfig.

Reviewed-by: Andre Przywar

env: Allow to build multiple environments in Kconfig

Now that we have everything in place in the code, let's allow to build
multiple environments backend through Kconfig.

Reviewed-by: Andre Przywara <andre.przywara@arm.com>
Reviewed-by: Lukasz Majewski <lukma@denx.de>
Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Maxime Ripard <maxime.ripard@free-electrons.com>

show more ...

Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here w

Kconfig: Migrate MTDIDS_DEFAULT / MTDPARTS_DEFAULT

We move all instances of CONFIG_MTDIDS_DEFAULT and
CONFIG_MTDPARTS_DEFAULT from the header files to the defconfig files.
There's a few cases here where we need to expand upon what was in the
header file.

Tested-by: Adam Ford <aford173@gmail.com> #omap3_logic
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...