Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

Merge branch '2019-03-25-master-imports'

- Convert various SPI related options to Kconfig

Convert CONFIG_DEFAULT_SPI_* to Kconfig

This converts the following to Kconfig:
CONFIG_DEFAULT_SPI_BUS
CONFIG_DEFAULT_SPI_MODE

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig scr

Convert CONFIG_SF_DEFAULT_* to Kconfig

This converts the following to Kconfig:
CONFIG_SF_DEFAULT_BUS
CONFIG_SF_DEFAULT_CS
CONFIG_SF_DEFAULT_MODE
CONFIG_SF_DEFAULT_SPEED

I use moveconfig script and then manual check on generated u-boot.cfg
to solve the remaining issue.

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-spi

- SPI-NOR support

configs: Don't use SPI_FLASH_BAR as default

Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing

configs: Don't use SPI_FLASH_BAR as default

Now that new SPI NOR layer uses stateless 4 byte opcodes by default,
don't enable SPI_FLASH_BAR. For SPI controllers that cannot support
4-byte addressing, (stm32_qspi.c, fsl_qspi.c, mtk_qspi.c, ich.c,
renesas_rpc_spi.c) add an imply clause to enable SPI_FLASH_BAR so as to
not break functionality.

Signed-off-by: Vignesh R <vigneshr@ti.com>
Tested-by: Simon Goldschmidt <simon.k.r.goldschmidt@gmail.com>
Tested-by: Stefan Roese <sr@denx.de>
Tested-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Jagan Teki <jagan@openedev.com>
Tested-by: Jagan Teki <jagan@amarulasolutions.com> #zynq-microzed

show more ...

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulas

Convert CONFIG_MII et al to Kconfig

This converts the following to Kconfig:
CONFIG_MII
CONFIG_DRIVER_TI_EMAC

Signed-off-by: Adam Ford <aford173@gmail.com>
Acked-by: Jagan Teki <jagan@amarulasolutions.com>
Acked-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANK

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SP

Convert CONFIG_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on the

Convert all of CONFIG_CONS_INDEX to Kconfig

This converts the following to Kconfig:
CONFIG_CONS_INDEX

We have existing entries for this option in a number of places, with
different guards on them. They're also sometimes used for things not
directly inside of the serial driver. First, introduce a new symbol to
guard the use of CONFIG_CONS_INDEX, so that in the case where we don't
need this for the serial driver, but for some other use, we can still do
it. Next, consolidate all of these into the single entry in
drivers/serial/Kconfig. Finally, introduce CONS_INDEX_[023456] so that
we can imply a correct value here to make the defconfig side of this
smaller.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Rework a lot of the logic here, such that I took authorship from
Adam, but kept his S-o-B line]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Migrate CONFIG_SPL_FRAMEWORK

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available f

configs: Migrate CONFIG_SPL_FRAMEWORK

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

spi: Migrate CONFIG_MXS_SPI to Kconfig

Signed-off-by: Tuomas Tynkkynen <tuomas@tuxera.com>

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removin

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_NAND_MXS to Kconfig

This converts CONFIG_NAND_MXS to Kconfig.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

arm: imx: mx28: Move MX28 selection to Kconfig

The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.

This selection method also alig

arm: imx: mx28: Move MX28 selection to Kconfig

The motivation for moving MX28 selection to Kconfig is to be able
to better handle NAND MXS selection through Kconfig.

This selection method also aligns with the way other i.MX SoCs are
selected in U-Boot.

Signed-off-by: Stefan Agner <stefan.agner@toradex.com>

show more ...

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/boo

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

show more ...

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[tri

common: Move CONFIG_BOOTARGS to Kconfig

Also introduce CONFIG_USE_BOOTARGS option so we can control if
CONFIG_BOOTARGS defined at all.

Signed-off-by: Sam Protsenko <semen.protsenko@linaro.org>
[trini: Resync r8a779[56]_ulcb, various ls10xx targets]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <a

configs: Migrate CMD_NAND*

Migrate all remaining instances of CMD_NAND, CMD_NAND_TRIMFFS
CMD_NAND_LOCK_UNLOCK and CMD_NAND_TORTURE from the headers into the
defconfig files.

Tested-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Bin Meng <bmeng.cn@gmail.com>

show more ...

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

Convert CONFIG_ENV_IS_IN_MMC/NAND/UBI and NOWHERE to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_MMC
CONFIG_ENV_IS_IN_NAND
CONFIG_ENV_IS_IN_UBI
CONFIG_ENV_IS_NOWHERE

In fact this already exists for sunxi as a 'choice' config. However not
all the choices are available in Kconfig yet so we cannot use that. It
would lead to more than one option being set.

In addition, one purpose of this series is to allow the environment to be
stored in more than one place. So the existing choice is converted to a
normal config allowing each option to be set independently.

There are not many opportunities for Kconfig updates to reduce the size of
this patch. This was tested with

./tools/moveconfig.py -i CONFIG_ENV_IS_IN_MMC

And then manual updates. This is because for CHAIN_OF_TRUST boards they
can only have ENV_IS_NOWHERE set, so we enforce that via Kconfig logic
now.

Signed-off-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Re-sync

Signed-off-by: Tom Rini <trini@konsulko.com>

disk: convert CONFIG_DOS_PARTITION to Kconfig

Signed-off-by: Patrick Delaunay <patrick.delaunay@st.com>
Signed-off-by: Patrick Delaunay <patrick.delaunay73@gmail.com>

Convert CONFIG_ARCH_MISC_INIT to Kconfig

This converts the following to Kconfig:
CONFIG_ARCH_MISC_INIT

Signed-off-by: Simon Glass <sjg@chromium.org>