Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_P

Convert CONFIG_FLASH_CFI_DRIVER et al to Kconfig

This converts the following to Kconfig:
CONFIG_FLASH_CFI_DRIVER
CONFIG_SYS_FLASH_USE_BUFFER_WRITE
CONFIG_FLASH_CFI_MTD
CONFIG_SYS_FLASH_PROTECTION
CONFIG_SYS_FLASH_CFI

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-migrate]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANK

configs: Migrate CONFIG_NR_DRAM_BANKS

We have the following cases:
- CONFIG_NR_DRAM_BANKS was defined, migrate normally
- CONFIG_NR_DRAM_BANKS_MAX was defined and then used for
CONFIG_NR_DRAM_BANKS after a check, just migrate it over now.
- CONFIG_NR_DRAM_BANKS was very oddly defined on p2771-0000-* (to 1024 +
2), set this to 8.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Convert CONFIG_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SP

Convert CONFIG_SPI to Kconfig

This converts the following to Kconfig:
CONFIG_SPI

This partly involves updating code that assumes that CONFIG_SPI implies
things that are specific to the MPC8xx SPI driver. For now, just update
the CONFIG tests. This also involves reworking the default for
CONFIG_SYS_DEF_EEPROM_ADDR so that we don't set it when we cannot make a
reasonable default, as it does not cause any compile failures.

Signed-off-by: Adam Ford <aford173@gmail.com>
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-riscv

configs: Drop CONFIG_MMC_NDS32

Remove CONFIG_MMC_NDS32 from the three config
(adp-ae3xx_defconfig, adp-ag101p_defconfig, nx25-ae250_defconfig).

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-

configs: Drop CONFIG_MMC_NDS32

Remove CONFIG_MMC_NDS32 from the three config
(adp-ae3xx_defconfig, adp-ag101p_defconfig, nx25-ae250_defconfig).

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>

show more ...

mmc: ftsdc010: Migrate CONFIG_FTSDC010_SDIO to Kconfig

Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.

Signed-off-by: Rick Chen <rick

mmc: ftsdc010: Migrate CONFIG_FTSDC010_SDIO to Kconfig

Convert CONFIG_FTSDC010_SDIO to Kconfig.
So CONFIG_FTSDC010_SDIO can also be
removed from config_whitelist.txt.

Signed-off-by: Rick Chen <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Cc: Greentime Hu <green.hu@gmail.com>

show more ...

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_P

Convert CONFIG_BOOTP_BOOTPATH et al to Kconfig

This converts the following to Kconfig:
CONFIG_BOOTP_BOOTPATH
CONFIG_BOOTP_DNS
CONFIG_BOOTP_GATEWAY
CONFIG_BOOTP_HOSTNAME
CONFIG_BOOTP_PXE
CONFIG_BOOTP_SUBNETMASK
CONFIG_CMDLINE_EDITING
CONFIG_AUTO_COMPLETE
CONFIG_SYS_LONGHELP
CONFIG_SUPPORT_RAW_INITRD
CONFIG_ENV_VARS_UBOOT_CONFIG

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Re-run the migration]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

configs: Migrate CONFIG_SPL_FRAMEWORK

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available f

configs: Migrate CONFIG_SPL_FRAMEWORK

Migrate the option CONFIG_SPL_FRAMEWORK and make this gate most of the
current set of options we have in Kconfig. We will need to have some
options available for SPL and !SPL_FRAMEWORK so this is important. In a
few cases we re-order existing options so that we have less escapes from
the SPL_FRAMEWORK guard.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removin

configs: Migrate CONFIG_SYS_TEXT_BASE

On the NIOS2 and Xtensa architectures, we do not have
CONFIG_SYS_TEXT_BASE set. This is a strict migration of the current
values into the defconfig and removing them from the headers.

I did not attempt to add more default values in and for now will leave
that to maintainers.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

configs: Resync with savedefconfig

Rsync all defconfig files using moveconfig.py

Signed-off-by: Tom Rini <trini@konsulko.com>

Move CONFIG_PANIC_HANG to Kconfig

Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
R

Move CONFIG_PANIC_HANG to Kconfig

Freescale (NXP) boards have lots of defconfig files per board.
I used "imply PANIC_HANG" for them.

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Reviewed-by: York Sun <york.sun@nxp.com>

show more ...

Merge git://git.denx.de/u-boot-nds32

nds32: board: Support ftsdc010 DM.

AG101P/AE3XX enable ftsdc010 dm flow.

Signed-off-by: Rick Chen <rick@andestech.com>

spi: nds_ae3xx: Rename nds_ae3xx_spi as atcspi200_spi

atcspi200 is Andestech spi ip which is embedded in
AE3XX and AE250 platforms. So rename as atcspi200
will be more reasonable to be used in diffe

spi: nds_ae3xx: Rename nds_ae3xx_spi as atcspi200_spi

atcspi200 is Andestech spi ip which is embedded in
AE3XX and AE250 platforms. So rename as atcspi200
will be more reasonable to be used in different
platforms.

Signed-off-by: Rick Chen <rick@andestech.com>

show more ...

ae3xx: timer: Rename AE3XX to ATCPIT100

ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.

Signed-off-by: rick <rick@a

ae3xx: timer: Rename AE3XX to ATCPIT100

ATCPIT100 is Andestech timer IP which is embeded
in AE3XX and AE250 boards. So rename AE3XX to
ATCPIT100 will be more make sence.

Signed-off-by: rick <rick@andestech.com>
Signed-off-by: Rick Chen <rickchen36@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/boo

cmd: Toggle the default value of CONFIG_CMD_IMLS

Having this as a 'default y' is rather annoying because it doesn't
actually compile unless other options are defined in the board header:

../cmd/bootm.c: In function 'do_imls_nor':
../cmd/bootm.c:330:7: error: 'CONFIG_SYS_MAX_FLASH_BANKS' undeclared (first use in this function); did you mean 'CONFIG_SYS_MAX_FLASH_SECT'?
i < CONFIG_SYS_MAX_FLASH_BANKS; ++i, ++info) {

Make it 'default n' so people who develop new boards that start from a
blank defconfig have one less compilation failure to debug.

Signed-off-by: Tuomas Tynkkynen <tuomas.tynkkynen@iki.fi>

show more ...

nds32: board: Support SPI driver.

Add spi dts node and enable spi dm flash config.

Signed-off-by: rick <rick@andestech.com>

Convert CONFIG_ENV_IS_IN_FLASH to Kconfig

This converts the following to Kconfig:
CONFIG_ENV_IS_IN_FLASH

Signed-off-by: Simon Glass <sjg@chromium.org>

configs: Resync defconfigs

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git://git.denx.de/u-boot-nds32

Move FTMAC100 to where it should be, alphabetically in
drivers/net/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
drivers/

Merge branch 'master' of git://git.denx.de/u-boot-nds32

Move FTMAC100 to where it should be, alphabetically in
drivers/net/Kconfig

Signed-off-by: Tom Rini <trini@konsulko.com>

Conflicts:
drivers/net/Kconfig

show more ...

nds32: eth: Support ftmac100 DM.

Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
Boot linux kernel via dhcp and bootm ok.

NDS32 # setenv bootm_size 0x20000

nds32: eth: Support ftmac100 DM.

Support Andestech eth ftmac100 device tree flow on AG101P/AE3XX platform.
Verification:
Boot linux kernel via dhcp and bootm ok.

NDS32 # setenv bootm_size 0x2000000;setenv fdt_high 0x1f00000;
NDS32 # dhcp 0x600000 10.0.4.97:boomimage-310y-ae300-spi.bin
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4899 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'boomimage-310y-ae300-spi.bin'.
Load address: 0x600000
Loading: #################################################################
#################################################################
#################################################################
...
...
###################################
233.4 KiB/s
done
Bytes transferred = 13872076 (d3abcc hex)
NDS32 # dhcp 0x2000000 10.0.4.97:ae300.dtb
BOOTP broadcast 1
BOOTP broadcast 2
BOOTP broadcast 3
BOOTP broadcast 4
DHCP client bound to address 10.0.4.178 (4592 ms)
Using mac@e0100000 device
TFTP from server 10.0.4.97; our IP address is 10.0.4.178
Filename 'ae300.dtb'.
Load address: 0x2000000
Loading: #
82 KiB/s
done
Bytes transferred = 2378 (94a hex)
NDS32 # bootm 0x600000 - 0x2000000
Image Name:
Created: 2017-03-22 6:52:03 UTC
Image Type: NDS32 Linux Kernel Image (uncompressed)
Data Size: 13872012 Bytes = 13.2 MiB
Load Address: 0000c000
Entry Point: 0000c000
Verifying Checksum ... OK
Booting using the fdt blob at 0x2000000
Loading Kernel Image ... OK
Loading Device Tree to 01efc000, end 01eff949 ... OK
Linux version 3.10.102-20375-gb0034c1-dirty (rick@app09)
(gcc version 4.9.3 (2016-07-06_nds32le-linux-glibc-v3_experimental) )
#293 PREEMPT Wed Mar 22 14:49:28 CST 2017
CPU: NDS32 N13, AndesCore ID(wb), CPU_VER 0x0d11103f(id 13, rev 17, cfg 4159)
...
...
Signed-off-by: rick <rick@andestech.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-nds32

nds32: Support AE3XX platform.

Support Andestech AE3xx platform: serial, timer device tree flow.

Signed-off-by: rick <rick@andestech.com>