Merge git://git.denx.de/u-boot-sunxi

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borro

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'rmobile' of git://git.denx.de/u-boot-sh

Merge git://git.denx.de/u-boot-rockchip

Merge branch 'master' of git://git.denx.de/u-boot-mpc85xx

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

udoo: Switch to SPL support

Currently we need to build one U-boot image for each of the udoo
variants: quad and dual-lite.

By switching to SPL we can support all two variants wi

udoo: Switch to SPL support

Currently we need to build one U-boot image for each of the udoo
variants: quad and dual-lite.

By switching to SPL we can support all two variants with a single binary.

Based on the SPL for wandboard.

Tested with OpenELEC (Open Embedded Linux Entertainment Center)
on both boards.

Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Cc: Fabio Estevam <fabio.estevam@freescale.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>
Signed-off-by: Peter Vicman <peter.vicman@gmail.com>
Acked-by: Fabio Estevam <fabio.estevam@freescale.com>

show more ...

Merge branch 'u-boot-microblaze/zynq' into 'u-boot-arm/master'

Merge branch 'master' of git://git.denx.de/u-boot-mips

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tric

Merge branch 'iu-boot/master' into 'u-boot-arm/master'

Conflicts:
arch/arm/cpu/arm926ejs/mxs/Makefile
board/compulab/cm_t35/Makefile
board/corscience/tricorder/Makefile
board/ppcag/bg0900/Makefile
drivers/bootcount/Makefile
include/configs/omap4_common.h
include/configs/pdnb3.h

Makefile conflicts are due to additions/removals of
object files on the ARM branch vs KBuild introduction
on the main branch. Resolution consists in adjusting
the list of object files in the main branch version.
This also applies to two files which are not listed
as conflicting but had to be modified:

board/compulab/common/Makefile
board/udoo/Makefile

include/configs/omap4_common.h conflicts are due to
the OMAP4 conversion to ti_armv7_common.h on the ARM
side, and CONFIG_SYS_HZ removal on the main side.
Resolution is to convert as this icludes removal of
CONFIG_SYS_HZ.

include/configs/pdnb3.h is due to a removal on ARM side.
Trivial resolution is to remove the file.

Note: 'git show' will also list two files just because
they are new:

include/configs/am335x_igep0033.h
include/configs/omap3_igep00x0.h

show more ...

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

udoo: Add initial support for mx6q udoo board

Add basic support for mx6q udoo board.

For further information about Udoo board:
http://www.udoo.org/

Tested booting a mai

udoo: Add initial support for mx6q udoo board

Add basic support for mx6q udoo board.

For further information about Udoo board:
http://www.udoo.org/

Tested booting a mainline device tree kernel and a Yocto rootfs from mmc.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>

show more ...