Merge git://git.denx.de/u-boot-sunxi

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borro

SPDX: Convert all of our single license tags to Linux Kernel style

When U-Boot started using SPDX tags we were among the early adopters and
there weren't a lot of other examples to borrow from. So we picked the
area of the file that usually had a full license text and replaced it
with an appropriate SPDX-License-Identifier: entry. Since then, the
Linux Kernel has adopted SPDX tags and they place it as the very first
line in a file (except where shebangs are used, then it's second line)
and with slightly different comment styles than us.

In part due to community overlap, in part due to better tag visibility
and in part for other minor reasons, switch over to that style.

This commit changes all instances where we have a single declared
license in the tag as both the before and after are identical in tag
contents. There's also a few places where I found we did not have a tag
and have introduced one.

Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge remote-tracking branch 'u-boot/master' into 'u-boot-arm/master'

Merge branch 'rmobile' of git://git.denx.de/u-boot-sh

Merge branch 'master' of git://git.denx.de/u-boot-x86

Merge branch 'master' of git://git.denx.de/u-boot-atmel

Merge branch 'master' of git://git.denx.de/u-boot-video

Conflicts:
include/splash.h

Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'master' of git://www.denx.de/git/u-boot-imx

mx53loco: Fix boot hang during reboot stress test

Currently by running the following test:

=> setenv bootcmd reset
=> save
=> reset

, we observe a hang after approx

mx53loco: Fix boot hang during reboot stress test

Currently by running the following test:

=> setenv bootcmd reset
=> save
=> reset

, we observe a hang after approximately 20-30 minutes of stress reboot test.

Investigation of this issue revealed that when a single DDR chip select is used,
the hang does not happen. It only happens when the two chip selects are active.

MX53 reference manual states at "28.6.2 Memory ZQ calibration sequence":

"The controller must keep the memory lines quiet (except for CK) for the ZQ
calibration time as defined in the Jedec (512 cycles for ZQCL after reset, 256
for other ZQCL and 64 for ZQCS)."

According to the SDE_0 and SDE_1 bit descriptions from register ESDCTL_ESDCTL:

"Writing 1 to SDE0 or SDE1 will initiate power up delays as JEDEC defines.
Power up delays are a function of the configured memory type (DDR2/DDR3/LPDDR2)"

So make sure to activate one chip select at time (CS0 first and then CS1 later),
so that the required JEDEC delay is respected for each chip select.

With this change applied the board has gone through three days of reboot stress
test without any hang.

Signed-off-by: Fabio Estevam <fabio.estevam@freescale.com>
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge branch 'next' of git://git.denx.de/u-boot-mpc83xx

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsab

Merge git://git.denx.de/u-boot-arm

Conflicts:
board/freescale/mx6qsabrelite/Makefile
board/freescale/mx6qsabrelite/mx6qsabrelite.c
include/configs/mx6qsabrelite.h

Signed-off-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge branch 'master' of git://www.denx.de/git/u-boot-cfi-flash

Merge branch 'u-boot/master' into u-boot-arm/master

Merge branch 'master' of git://git.denx.de/u-boot-nds32

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
bo

Merge branch 'master' of git://git.denx.de/u-boot-i2c

The sandburst-specific i2c drivers have been deleted, conflict was just
over the SPDX conversion.

Conflicts:
board/sandburst/common/ppc440gx_i2c.c
board/sandburst/common/ppc440gx_i2c.h

Signed-off-by: Tom Rini <trini@ti.com>

show more ...

Add GPL-2.0+ SPDX-License-Identifier to source files

Signed-off-by: Wolfgang Denk <wd@denx.de>
[trini: Fixup common/cmd_io.c]
Signed-off-by: Tom Rini <trini@ti.com>

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'

Conflicts:
spl/Makefile

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Conflicts:
drivers/serial/Makefile

Merge branch 'master' of git://git.denx.de/u-boot-video

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
common/cmd_fpga.c
drivers/usb/host/ohci-at91.c

Merge branch 'patman' of git://git.denx.de/u-boot-x86

Fix references to the documentation files

Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and fil

Fix references to the documentation files

Many boot image configuration files refer to the
appropriate documentation file, but these references
contain typos in the directory and file name. Fix
them. Also fix reference to doc/README.SPL file.

Signed-off-by: Anatolij Gustschin <agust@denx.de>
Cc: Prafulla Wadaskar <prafulla@marvell.com>
Cc: Stefano Babic <sbabic@denx.de>
Acked-by: Stefano Babic <sbabic@denx.de>

show more ...

Merge 'u-boot-microblaze/mainline/arm' into 'u-boot-arm/master'

This pulls the three following ZYNQ commits into ARM master:

7dca54f8: xilinx: zynq: Enable DCC and create new zynq_d

Merge 'u-boot-microblaze/mainline/arm' into 'u-boot-arm/master'

This pulls the three following ZYNQ commits into ARM master:

7dca54f8: xilinx: zynq: Enable DCC and create new zynq_dcc board
59c651f4: arm: zynq: Add SLCR support with system reset
00ed3458: arm: zynq: Add lowlevel initialization to C

show more ...