microblaze: Convert generic platform to DM gpio

Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sys

microblaze: Convert generic platform to DM gpio

Converting GPIO to DM requires to do changes in reset subsystem
that's why support for Microblaze soft reset via sysreset and GPIO
sysreset support was added.
These two patches enables enabling GPIO DM.
Microblaze soft reset is bind at last reset method.

GPIO reset is handled via sysreset with adding this fragment to DT.

gpio-restart {
compatible = "gpio-restart";
gpios = <&reset_gpio 0 0 0>;
/* 3rd cell ACTIVE_HIGH = 0, ACTIVE_LOW = 1 */
};

hard-reset-gpio property is not documented and also handled.
Conversion is required.

Unfortunately do_reset is required for SPL that's why use only soft
microblaze reset for now.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge branch 'buildman' of git://git.denx.de/u-boot-x86

Coding Style cleanup: remove trailing empty lines

Signed-off-by: Wolfgang Denk <wd@denx.de>

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Merge branch 'u-boot-samsung/master' into 'u-boot-arm/master'

Conflicts:
spl/Makefile

Merge branch 'u-boot-imx/master' into 'u-boot-arm/master'

Conflicts:
drivers/serial/Makefile

Merge branch 'master' of git://git.denx.de/u-boot-video

Merge branch 'u-boot/master' into 'u-boot-arm/master'

Conflicts:
common/cmd_fpga.c
drivers/usb/host/ohci-at91.c

gpio: Add support for microblaze xilinx GPIO

Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.

Add gpio driver and change

gpio: Add support for microblaze xilinx GPIO

Microblaze uses gpio which is connected to the system reset.
Currently gpio subsystem wasn't used for it.

Add gpio driver and change Microblaze reset logic to be done
via gpio subsystem.

There are various configurations which Microblaze can have
that's why gpio_alloc/gpio_alloc_dual(for dual channel)
function has been introduced and gpio can be allocated
dynamically.

Adding several gpios IP is also possible and supported.

For listing gpio configuration please use "gpio status" command

This patch also remove one compilation warning:
microblaze-generic.c: In function 'do_reset':
microblaze-generic.c:38:47: warning: operation on '*1073741824u'
may be undefined [-Wsequence-point]

Signed-off-by: Michal Simek <michal.simek@xilinx.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-i2c

* 'master' of git://git.denx.de/u-boot-i2c:
km/common: remove printfs for i2c deblocking code
CONFIG: SMDK5250: I2C: Enable

Merge branch 'master' of git://git.denx.de/u-boot-i2c

* 'master' of git://git.denx.de/u-boot-i2c:
km/common: remove printfs for i2c deblocking code
CONFIG: SMDK5250: I2C: Enable I2C
I2C: Add support for Multi channel
I2C: Modify the I2C driver for EXYNOS5
I2C: Move struct s3c24x0_i2c to a common place.
EXYNOS: PINMUX: Add pinmux support for I2C
EXYNOS5: define EXYNOS5_I2C_SPACING
EXYNOS: Add I2C base address.
EXYNOS: CLK: Add i2c clock
mx6qsabrelite: add i2c multi-bus support
imx-common: add i2c.c for bus recovery support
i.mx53: add definition for I2C3_BASE_ADDR
i.mx: iomux-v3.c: move to imx-common directory
i.mx: iomux-v3.h: move to imx-common include directory
iomux-v3: remove include of mx6x_pins.h
mxc_i2c: finish adding CONFIG_I2C_MULTI_BUS support
mxc_i2c: add bus recovery support
mxc_i2c: prep work for multiple busses support
mxc_i2c: add i2c_regs argument to i2c_imx_stop
mxc_i2c: add retries
mxc_i2c: check for arbitration lost
mxc_i2c: change slave addr if conflicts with destination.
mxc_i2c: don't disable controller after every transaction
mxc_i2c: place i2c_reset code inline
mxc_i2c: place imx_start code inline
mxc_i2c: remove redundant read
mxc_i2c: combine i2c_imx_bus_busy and i2c_imx_trx_complete into wait_for_sr_state
mxc_i2c.c: code i2c_probe as a 0 length i2c_write
mxc_i2c: call i2c_imx_stop on error in i2c_read/i2c_write
mxc_i2c: create i2c_init_transfer
mxc_i2c: clear i2sr before waiting for bit
mxc_i2c: create tx_byte function
mxc_i2c: remove ifdef of CONFIG_HARD_I2C
mxc_i2c: fix i2c_imx_stop
i2c: deblock i2c bus also if accessed before realocation

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-microblaze

* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Wire up SPI driver
spi: microblaze: Adds driver for Xi

Merge branch 'master' of git://git.denx.de/u-boot-microblaze

* 'master' of git://git.denx.de/u-boot-microblaze:
microblaze: Wire up SPI driver
spi: microblaze: Adds driver for Xilinx SPI controller
microblaze: intc: Clear interrupt code
microblaze: Call serial multi initialization
microblaze: Move __udelay implementation
microblaze: Remove extern from board.c
microblaze: Wire up dts configuration
fdt: Add board specific dts inclusion
microblaze: Move individual board linker scripts to common script in cpu tree.
microblaze: Add gpio.h
microblaze: Add missing undefs for UBI and UBIFS
microblaze: Expand and correct configuration comments
microblaze: Enable ubi support
microblaze: Avoid compile error on systems without cfi flash
microblaze: Remove wrong define CONFIG_SYS_FLASH_PROTECTION

Conflicts:
drivers/spi/Makefile

Signed-off-by: Wolfgang Denk <wd@denx.de>

show more ...

microblaze: Add gpio.h

Gpio support is not implemented yet. Adding it because of fdtdec.

Signed-off-by: Michal Simek <monstr@monstr.eu>