Merge tag 'u-boot-amlogic-20181126' of git://git.denx.de/u-boot-amlogic

Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
- net: designware: add mes

Merge tag 'u-boot-amlogic-20181126' of git://git.denx.de/u-boot-amlogic

Cleanup and update towards support for Amlogic Meson AXG SoCs :
- mmc: meson-gx: Add AXG compatible
- net: designware: add meson meson compatibles
- Amlogic Meson cleanup for AXG SoC support

show more ...

ARM: meson: Add boot device discovery

The Amlogic Meson SoCs ROM supports a boot over USB with a custom protocol.

When no other boot medium are available (or by forcing the USB mode), the
ROM sets

ARM: meson: Add boot device discovery

The Amlogic Meson SoCs ROM supports a boot over USB with a custom protocol.

When no other boot medium are available (or by forcing the USB mode), the
ROM sets the primary USB port as device mode and waits for a Host to
enumerate.

When enumerated, a custom protocol described at [1] permits writing to
memory and execute some specific FIP init code to run the loaded
Arm Trusted Firmware BL2 and BL3 stages before running the BL33 stage.

In this mode, we can load different binaries that can be used by U-boot
like a script image file.

This adds support for a custom USB boot stage only available when the
boot mode is USB and the script file at a pre-defined address is valid.
This support was heavily copied from the Sunxi Allwinner FEL U-Boot support.

The tool pyamlboot described at [2], permits using this boot mode on boards
exposing the first USB port, either as OTG or Host port.

[1] https://github.com/superna9999/pyamlboot/blob/master/PROTOCOL.md
[2] https://github.com/superna9999/pyamlboot/blob/master/README.md

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

board: amlogic: add support for S400 board

The S400 board is the Amlogic AXG SoC reference board including :
- Amlogic A113DX ARM Cortex-A53 quad-core SoC @ 1.2GHz
- 1GB DDR4 SDRAM
- 10/100 Ether

board: amlogic: add support for S400 board

The S400 board is the Amlogic AXG SoC reference board including :
- Amlogic A113DX ARM Cortex-A53 quad-core SoC @ 1.2GHz
- 1GB DDR4 SDRAM
- 10/100 Ethernet
- 2 x USB 2.0 Host
- eMMC
- Infrared receiver
- SDIO WiFi Module
- MIPI DSI Connector
- Audio HAT Connector
- PCI-E M.2 Connectors

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

ARM: meson: Add support for AXG family

This patch adds support for the Amlogic AXG SoC, which is very close from
the Amlogic GXL SoCs with :
- Same 4xCortex-A53 CPUs but clocked at 1.2GHZ max
- DDR

ARM: meson: Add support for AXG family

This patch adds support for the Amlogic AXG SoC, which is very close from
the Amlogic GXL SoCs with :
- Same 4xCortex-A53 CPUs but clocked at 1.2GHZ max
- DDR Interface limited to DDR4 16bit
- The whole physical register address space has been moved to 0xfxxxxxxx
- The pinctrl setup has changed
- The clock tree is different enough to use a different driver

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

ARM: meson: rework soc arch file to prepare for new SoC

We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are diffe

ARM: meson: rework soc arch file to prepare for new SoC

We are about to add support for the Amlogic AXG SoC. While very close to
the Gx SoC family, we will need to handle a few thing which are different
in this SoC. Rework the meson arch directory to prepare for this.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

ARM: rework amlogic configuration

Rework the board SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME setup by moving
the board Kconfig into the mach-meson Kconfig to make it easier to add
new boards for a S

ARM: rework amlogic configuration

Rework the board SYS_BOARD, SYS_VENDOR and SYS_CONFIG_NAME setup by moving
the board Kconfig into the mach-meson Kconfig to make it easier to add
new boards for a SoC architecture and add a custom config header or custom
board handler for a platform.

This drops the board CONFIGs and the duplicate boards configs headers in
favor of a single meson64.h config header.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

board: amlogic: factorise gxbb boards

The nanopi-k2 and the odroid-c2 are similar enough to be supported
by the same u-boot board. This change use odroid-c2 u-boot board
for the nanopi-k2 as well. D

board: amlogic: factorise gxbb boards

The nanopi-k2 and the odroid-c2 are similar enough to be supported
by the same u-boot board. This change use odroid-c2 u-boot board
for the nanopi-k2 as well. Dedicated defconfig are kept to customize
the names and device tree.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

board: amlogic: move khadas-vim2 as q200 ref board

The Khadas vim2 derive from amlogic s912 reference design (Q200).

This patch moves the khadas-vim2 board support to a generic Q200 board,
while ke

board: amlogic: move khadas-vim2 as q200 ref board

The Khadas vim2 derive from amlogic s912 reference design (Q200).

This patch moves the khadas-vim2 board support to a generic Q200 board,
while keeping a dedicated defconfig to customize the names and device tree.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

board: amlogic: remove p212 derivatives

The Khadas vim and the libretech aml-s905x-cc (aka Potato) derive
from amlogic s905x reference design (P212).

All the code in these board is a copy/paste fro

board: amlogic: remove p212 derivatives

The Khadas vim and the libretech aml-s905x-cc (aka Potato) derive
from amlogic s905x reference design (P212).

All the code in these board is a copy/paste from the p212, which is
tedious to maintain. This change use p212 u-boot board for all these
boards, while keeping a dedicated defconfig to customize the names
and device tree.

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

ARM: meson: clean-up platform selection

Even if multiple board are selected through Kconfig, u-boot will only
compile one. This makes sense since compiling these targets will export
global symbols,

ARM: meson: clean-up platform selection

Even if multiple board are selected through Kconfig, u-boot will only
compile one. This makes sense since compiling these targets will export
global symbols, such as board_init()

The change rework amlogic Kconfig so only one board may be selected at
a time

Signed-off-by: Jerome Brunet <jbrunet@baylibre.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

ARM: meson: Add Khadas VIM2 board support

This adds platform code for the Khadas VIM2 board based on a
Meson GXM (S912) SoC with the Meson GXM configuration.

This initial submission supports UART,

ARM: meson: Add Khadas VIM2 board support

This adds platform code for the Khadas VIM2 board based on a
Meson GXM (S912) SoC with the Meson GXM configuration.

This initial submission supports UART, MMC/SDCard and Ethernet.
USB is partially supported.

All the code is from Neil Armstrong! I just rebased the code, do
some cleanup and tested on my board.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Signed-off-by: Loic Devulder <ldevulder@suse.de>
Acked-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

dm: Change CMD_DM enabling

CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use

dm: Change CMD_DM enabling

CMD_DM is used for debug purpose and it shouldn't be enabled by default
via Kconfig. Unfortunately this is in the tree for quite a long time
that's why solution is to use imply DM for all targets which are
enabling DM.

Signed-off-by: Michal Simek <michal.simek@xilinx.com>
Reviewed-by: Tom Rini <trini@konsulko.com>
Reviewed-by: Joe Hershberger <joe.hershberger@ni.com>

show more ...

boards: amlogic: Fix boards README

Fix typos and update the supported devices for all Amlogic boards.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

boards: amlogic: Add FriendlyElec NanoPi K2 board support

This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.

This initi

boards: amlogic: Add FriendlyElec NanoPi K2 board support

This adds platform code for the FriendlyElec NanoPi K2 board based on a
Meson GXBB (S905) SoC with the Meson GXBB configuration.

This initial submission only supports:
- UART
- MMC/SDCard
- Ethernet
- Reset Controller
- Clock controller

Cc: Yuefei Tan <yftan@friendlyarm.com>
Signed-off-by: Thomas McKahan <tonymckahan@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

clk: add Amlogic meson clock driver

Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.

Signed-off-by: Beniamino Galvani

clk: add Amlogic meson clock driver

Introduce a basic clock driver for Amlogic Meson SoCs which supports
enabling/disabling clock gates and getting their frequency.

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

arm: Add Khadas VIM support based on Meson GXL family

This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission sup

arm: Add Khadas VIM support based on Meson GXL family

This adds platform code for the Khadas VIM board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.

The meson-gxl-s905x-khadas-vim.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

arm: Add LibreTech CC support based on Meson GXL family

This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This i

arm: Add LibreTech CC support based on Meson GXL family

This adds platform code for the Libre Computer CC "Le Potato" board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission supports UART, MMC/SDCard and Ethernet with the
Internal RMII PHY.

The meson-gxl-s905x-libretech-cc.dts is synchronised from the linux 4.13
stable tree as of 4.13.8.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>

show more ...

arm: add initial support for Amlogic P212 based on Meson GXL family

This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

T

arm: add initial support for Amlogic P212 based on Meson GXL family

This adds platform code for the Amlogic P212 reference board based on a
Meson GXL (S905X) SoC with the Meson GXL configuration.

This initial submission only supports UART and MMC/SDCard, support for the
internal Ethernet PHY in Work In Progress.

Signed-off-by: Neil Armstrong <narmstrong@baylibre.com>
Reviewed-by: Beniamino Galvani <b.galvani@gmail.com>

show more ...

board: amlogic: Rename folder for Amlogic boards

s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caio

board: amlogic: Rename folder for Amlogic boards

s/hardkernel/amlogic/ to have a single place for all the amlogic-based
boards.

Reviewed-by: Simon Glass <sjg@chromium.org>
Signed-off-by: Carlo Caione <carlo@endlessm.com>
Acked-by: Beniamino Galvani <b.galvani@gmail.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot

Signed-off-by: Stefano Babic <sbabic@denx.de>

arm: add initial support for Amlogic Meson and ODROID-C2

This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
U

arm: add initial support for Amlogic Meson and ODROID-C2

This adds platform code for the Amlogic Meson GXBaby (S905) SoC and a
board definition for ODROID-C2. This initial submission only supports
UART and Ethernet (through the existing Designware driver). DTS files
are the ones submitted to Linux arm-soc for 4.7 [1].

[1] https://patchwork.ozlabs.org/patch/603583/

Signed-off-by: Beniamino Galvani <b.galvani@gmail.com>
Reviewed-by: Simon Glass <sjg@chromium.org>

show more ...