Merge branch 'master' of git://git.denx.de/u-boot-spi

This is the PR for SPI-NAND changes along with few spi changes.

[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Si

Merge branch 'master' of git://git.denx.de/u-boot-spi

This is the PR for SPI-NAND changes along with few spi changes.

[trini: Re-sync changes for ls1012afrwy_qspi*_defconfig]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-dm

Merge branch 'master' of git://git.denx.de/u-boot-video

Signed-off-by: Tom Rini <trini@konsulko.com>

Merge branch 'master' of git://git.denx.de/u-boot-sunxi

Merge tag 'mpc85xx-for-v2018.11-rc1' of git://git.denx.de/u-boot-mpc85xx

Use device tree for mpc85xx with binman. Enabled for T2080QDS.

Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq

Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.

Merge tag 'fsl-qoriq-for-v2018.11-rc1' of git://git.denx.de/u-boot-fsl-qoriq

Switch to driver model for eSDHC on Layerscape SoCs including LS1021A,
LS1043A, LS1046A, LS1088A, LS2088A.
Switch to driver model for SATA on LS1021A and LS1043A.
Add support for LS1012AFRWY rev C board.
Enable SMMU for LS1043A.

show more ...

mmc: omap_mmc: Remove invert references

With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch remov

mmc: omap_mmc: Remove invert references

With DM_GPIO and DM_MMC translating GPIO_ACTIVE_LOW, any boards
using the 'cd-invert' option will no longer need to do this. This
patch removes the support for 'invert' from the MMC driver.

Signed-off-by: Adam Ford <aford173@gmail.com>
[trini: Fix warning over when !DM_GPIO]
Signed-off-by: Tom Rini <trini@konsulko.com>

show more ...

Merge branch 'master' of git://git.denx.de/u-boot-socfpga

Merge git://git.denx.de/u-boot-mmc

mmc: omap_hsmmc: do not embed struct mmc in struct omap_hsmmc_plat

The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is us

mmc: omap_hsmmc: do not embed struct mmc in struct omap_hsmmc_plat

The area for struct mmc can be allocated dynamically. It greatly reduces
the size of struct omap_hsmmc_plat. This is useful in cases where the board
level code declares one or two struct omap_hsmmc_plat because it doesn't
use the Driver Model.

This saves around 740 bytes for the am335x_evm SPL.

Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>
Tested-by: Adam Ford <aford173@gmail.com>
Reviewed-by: Tom Rini <trini@konsulko.com>

show more ...

Merge git://git.denx.de/u-boot-imx

Merge git://git.denx.de/u-boot-mmc

ARM: OMAP5: set mmc clock frequency to 192MHz

Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MH

ARM: OMAP5: set mmc clock frequency to 192MHz

Now that omap_hsmmc has support for hs200 mode, change the clock
frequency to 192MHz. Also change the REFERENCE CLOCK frequency to
192MHz based on which the internal mmc clock divider is calculated.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: add signal voltage selection support

I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support

mmc: omap_hsmmc: add signal voltage selection support

I/O data lines of UHS SD card operates at 1.8V when in UHS speed
mode (same is true for eMMC in DDR and HS200 modes). Add support
to switch signal voltage to 1.8V in order to support
UHS cards and eMMC HS200 and DDR modes.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: Add support to get pinctrl values and max frequency for different hw revisions

AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0.

mmc: omap_hsmmc: Add support to get pinctrl values and max frequency for different hw revisions

AM572x SR1.1 requires different IODelay values to be used than that used
in AM572x SR2.0. These values are populated in device tree. Add
capability in omap_hsmmc driver to extract IOdelay values for different
silicon revision. The maximum frequency is also reduced when using a ES1.1.
To keep the ability to boot both revsions with the same dtb, those values
can be provided by the platform code.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: Workaround for errata id i802

According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.

The DCRC interrup

mmc: omap_hsmmc: Workaround for errata id i802

According to errata i802, DCRC error interrupts
(MMCHS_STAT[21] DCRC=0x1) can occur during the tuning procedure.

The DCRC interrupt, occurs when the last tuning block fails
(the last ratio tested). The delay from CRC check until the
interrupt is asserted is bigger than the delay until assertion
of the tuning end flag. Assertion of tuning end flag is what
masks the interrupts. Because of this race, an erroneous DCRC
interrupt occurs.

The suggested workaround is to disable DCRC interrupts during
the tuning procedure which is implemented here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: Add tuning support

HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the

mmc: omap_hsmmc: Add tuning support

HS200/SDR104 requires tuning command to be sent to the card. Use
the mmc_send_tuning library function to send the tuning
command and configure the internal DLL.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: Enable DDR mode support

In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.

Signed-off-by: Kishon Vijay Abrah

mmc: omap_hsmmc: Enable DDR mode support

In order to enable DDR mode, Dual Data Rate mode bit has to be set in
MMCHS_CON register. Set it here.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: set MMC mode in the UHSMS bit field

Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support

mmc: omap_hsmmc: set MMC mode in the UHSMS bit field

Use the timing parameter set in the MMC core to set the
mode in UHSMS bit field. This is in preparation for
adding HS200 support in omap hsmmc driver.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: add support to set default io voltage

"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-vol

mmc: omap_hsmmc: add support to set default io voltage

"ti,dual-volt" is used in linux kernel to set the voltage capabilities.
For host controller dt nodes that doesn't have "ti,dual-volt",
it's assumed 1.8v is the io voltage. This is not always true (like in
the case of beagle-x15 where the io lines are connected to 3.3v).
Hence if "no-1-8-v" property is set, io voltage will be set to 3v.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

mmc: omap_hsmmc: cleanup clock configuration

Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
b

mmc: omap_hsmmc: cleanup clock configuration

Add a separate function for starting the clock, stopping the clock and
setting the clock. Starting the clock and stopping the clock can
be used irrespective of setting the clock (For example during iodelay
recalibration).
Also set the clock only if there is a change in frequency.

Signed-off-by: Kishon Vijay Abraham I <kishon@ti.com>
Signed-off-by: Jean-Jacques Hiblot <jjhiblot@ti.com>

show more ...

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates

Merge tag 'xilinx-for-v2018.03' of git://git.denx.de/u-boot-microblaze

Xilinx changes for v2018.03

- Several Kconfig fixes (also moving configs to defconfigs)
- Some DTS updates
- ZynqMP psu rework based on Zynq concept
- Add low level initialization for zc770 and zcu102
- Add support for Zynq zc770 x16 nand configuration
- Add mini nand/emmc ZynqMP targets
- Some arasan nand changes

show more ...

Merge git://git.denx.de/u-boot-spi

Merge git://git.denx.de/u-boot-marvell

Merge git://git.denx.de/u-boot-arc