misc/pca955*: Move models under hw/gpio

The PCA9552 and PCA9554 devices are both I2C GPIO controllers and the
PCA9552 also can drive LEDs. Do all the necessary adjustments to move
the models under h

misc/pca955*: Move models under hw/gpio

The PCA9552 and PCA9554 devices are both I2C GPIO controllers and the
PCA9552 also can drive LEDs. Do all the necessary adjustments to move
the models under hw/gpio.

Cc: Glenn Miles <milesg@linux.vnet.ibm.com>
Signed-off-by: Cédric Le Goater <clg@redhat.com>
Message-ID: <20240325134833.1484265-1-clg@redhat.com>
Reviewed-by: Thomas Huth <thuth@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>

show more ...

hw/gpio: Implement STM32L4x5 GPIO

Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externa

hw/gpio: Implement STM32L4x5 GPIO

Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externally" (using input
irqs) results in an out irq (transmitted to SYSCFG)
- output mode : setting a bit in ODR sets the corresponding out irq
(if this line is configured in output mode)
- pull-up, pull-down
- push-pull, open-drain

Difference with the real GPIOs :
- Alternate Function and Analog mode aren't implemented :
pins in AF/Analog behave like pins in input mode
- floating pins stay at their last value
- register IDR reset values differ from the real one :
values are coherent with the other registers reset values
and the fact that AF/Analog modes aren't implemented
- setting I/O output speed isn't supported
- locking port bits isn't supported
- ADC function isn't supported
- GPIOH has 16 pins instead of 2 pins
- writing to registers LCKR, AFRL, AFRH and ASCR is ineffective

Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240305210444.310665-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

hw/gpio Add GPIO read/write trace event.

Add GPIO read/write trace event for aspeed model.

Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-I

hw/gpio Add GPIO read/write trace event.

Add GPIO read/write trace event for aspeed model.

Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Reviewed-by: Cédric Le Goater <clg@kaod.org>
Message-Id: <20220525053444.27228-2-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

show more ...

hw/gpio: Add ASPEED GPIO model for AST1030

1. Add GPIO read/write trace event.
2. Support GPIO index mode for write operation.
It did not support GPIO index mode for read operation.
3. AST1030 integ

hw/gpio: Add ASPEED GPIO model for AST1030

1. Add GPIO read/write trace event.
2. Support GPIO index mode for write operation.
It did not support GPIO index mode for read operation.
3. AST1030 integrates one set of Parallel GPIO Controller
with maximum 151 control pins, which are 21 groups
(A~U, exclude pin: M6 M7 Q5 Q6 Q7 R0 R1 R4 R5 R6 R7 S0 S3 S4
S5 S6 S7 ) and the group T and U are input only.

Signed-off-by: Jamin Lin <jamin_lin@aspeedtech.com>
Message-Id: <20220321091453.17113-2-jamin_lin@aspeedtech.com>
Signed-off-by: Cédric Le Goater <clg@kaod.org>

show more ...

Merge remote-tracking branch 'remotes/cohuck-gitlab/tags/s390x-20210708' into staging

s390x updates:
- add gen16 cpumodels
- refactor/cleanup some code
- bugfixes

# gpg:

Merge remote-tracking branch 'remotes/cohuck-gitlab/tags/s390x-20210708' into staging

s390x updates:
- add gen16 cpumodels
- refactor/cleanup some code
- bugfixes

# gpg: Signature made Thu 08 Jul 2021 12:26:21 BST
# gpg: using EDDSA key 69A3B536F5CBFC65208026C1DE88BB5641DE66C1
# gpg: issuer "cohuck@redhat.com"
# gpg: Good signature from "Cornelia Huck <conny@cornelia-huck.de>" [unknown]
# gpg: aka "Cornelia Huck <huckc@linux.vnet.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cornelia.huck@de.ibm.com>" [full]
# gpg: aka "Cornelia Huck <cohuck@kernel.org>" [unknown]
# gpg: aka "Cornelia Huck <cohuck@redhat.com>" [unknown]
# Primary key fingerprint: C3D0 D66D C362 4FF6 A8C0 18CE DECF 6B93 C6F0 2FAF
# Subkey fingerprint: 69A3 B536 F5CB FC65 2080 26C1 DE88 BB56 41DE 66C1

* remotes/cohuck-gitlab/tags/s390x-20210708:
target/s390x: split sysemu part of cpu models
target/s390x: move kvm files into kvm/
target/s390x: remove kvm-stub.c
target/s390x: use kvm_enabled() to wrap call to kvm_s390_get_hpage_1m
target/s390x: make helper.c sysemu-only
target/s390x: split cpu-dump from helper.c
target/s390x: move sysemu-only code out to cpu-sysemu.c
target/s390x: start moving TCG-only code to tcg/
target/s390x: rename internal.h to s390x-internal.h
target/s390x: remove tcg-stub.c
hw/s390x: only build tod-tcg from the CONFIG_TCG build
hw/s390x: tod: make explicit checks for accelerators when initializing
hw/s390x: rename tod-qemu.c to tod-tcg.c
target/s390x: meson: add target_user_arch
s390x/tcg: Fix m5 vs. m4 field for VECTOR MULTIPLY SUM LOGICAL
target/s390x: Fix CC set by CONVERT TO FIXED/LOGICAL
s390x/cpumodel: add 3931 and 3932

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/rth-gitlab/tags/pull-tcg-20210710' into staging

Add translator_use_goto_tb.
Cleanups in prep of breakpoint fixes.
Misc fixes.

# gpg: Si

Merge remote-tracking branch 'remotes/rth-gitlab/tags/pull-tcg-20210710' into staging

Add translator_use_goto_tb.
Cleanups in prep of breakpoint fixes.
Misc fixes.

# gpg: Signature made Sat 10 Jul 2021 16:29:14 BST
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F

* remotes/rth-gitlab/tags/pull-tcg-20210710: (41 commits)
cpu: Add breakpoint tracepoints
tcg: Remove TCG_TARGET_HAS_goto_ptr
accel/tcg: Log tb->cflags with -d exec
accel/tcg: Split out log_cpu_exec
accel/tcg: Move tb_lookup to cpu-exec.c
accel/tcg: Move helper_lookup_tb_ptr to cpu-exec.c
target/i386: Use cpu_breakpoint_test in breakpoint_handler
tcg: Fix prologue disassembly
target/xtensa: Use translator_use_goto_tb
target/tricore: Use tcg_gen_lookup_and_goto_ptr
target/tricore: Use translator_use_goto_tb
target/sparc: Use translator_use_goto_tb
target/sh4: Use translator_use_goto_tb
target/s390x: Remove use_exit_tb
target/s390x: Use translator_use_goto_tb
target/rx: Use translator_use_goto_tb
target/riscv: Use translator_use_goto_tb
target/ppc: Use translator_use_goto_tb
target/openrisc: Use translator_use_goto_tb
target/nios2: Use translator_use_goto_tb
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging

* More SVM fixes (Lara)
* Module annotation database (Gerd)
* Memory leak fixes (myself)
* Bu

Merge remote-tracking branch 'remotes/bonzini-gitlab/tags/for-upstream' into staging

* More SVM fixes (Lara)
* Module annotation database (Gerd)
* Memory leak fixes (myself)
* Build fixes (myself)
* --with-devices-* support (Alex)

# gpg: Signature made Fri 09 Jul 2021 17:23:52 BST
# gpg: using RSA key F13338574B662389866C7682BFFBD25F78C7AE83
# gpg: issuer "pbonzini@redhat.com"
# gpg: Good signature from "Paolo Bonzini <bonzini@gnu.org>" [full]
# gpg: aka "Paolo Bonzini <pbonzini@redhat.com>" [full]
# Primary key fingerprint: 46F5 9FBD 57D6 12E7 BFD4 E2F7 7E15 100C CD36 69B1
# Subkey fingerprint: F133 3857 4B66 2389 866C 7682 BFFB D25F 78C7 AE83

* remotes/bonzini-gitlab/tags/for-upstream: (48 commits)
meson: Use input/output for entitlements target
configure: allow the selection of alternate config in the build
configs: rename default-configs to configs and reorganise
hw/arm: move CONFIG_V7M out of default-devices
hw/arm: add dependency on OR_IRQ for XLNX_VERSAL
meson: Introduce target-specific Kconfig
meson: switch function tests from compilation to linking
vl: fix leak of qdict_crumple return value
target/i386: fix exceptions for MOV to DR
target/i386: Added DR6 and DR7 consistency checks
target/i386: Added MSRPM and IOPM size check
monitor/tcg: move tcg hmp commands to accel/tcg, register them dynamically
usb: build usb-host as module
monitor/usb: register 'info usbhost' dynamically
usb: drop usb_host_dev_is_scsi_storage hook
monitor: allow register hmp commands
accel: build tcg modular
accel: add tcg module annotations
accel: build qtest modular
accel: add qtest module annotations
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging

Trivial patches pull request 20210709

# gpg: Signature made Fri 09 Jul 2021 21:2

Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-6.1-pull-request' into staging

Trivial patches pull request 20210709

# gpg: Signature made Fri 09 Jul 2021 21:26:52 BST
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C

* remotes/vivier2/tags/trivial-branch-for-6.1-pull-request:
util/guest-random: Fix size arg to tail memcpy
migration: fix typo in mig_throttle_guest_down comment
target/xtensa/xtensa-semi: Fix compilation problem on Haiku
hw/virtio: Document *_should_notify() are called within rcu_read_lock()
misc: Remove redundant new line in perror()
virtiofsd: Add missing newline in error message
misc: Fix "havn't" typo
memory: Display MemoryRegion name in read/write ops trace events
qemu-option: Drop dead assertion

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-2' into staging

Some qemu updates for IPMI and I2C

Move some ADC file to where they belong and move some sensors to

Merge remote-tracking branch 'remotes/cminyard/tags/for-qemu-6.1-2' into staging

Some qemu updates for IPMI and I2C

Move some ADC file to where they belong and move some sensors to a
sensor directory, since with new BMCs coming in lots of different
sensors should be coming in. Keep from cluttering things up.

Add support for I2C PMBus devices.

Replace the confusing and error-prone i2c_send_recv and i2c_transfer with
specific send and receive functions. Several errors have already been
made with these, avoid any new errors.

Fix the watchdog_expired field in the IPMI watchdog, it's not a bool,
it's a u8. After a vmstate transfer, the new value could be wrong.

# gpg: Signature made Fri 09 Jul 2021 17:25:04 BST
# gpg: using RSA key FD0D5CE67CE0F59A6688268661F38C90919BFF81
# gpg: Good signature from "Corey Minyard <cminyard@mvista.com>" [unknown]
# gpg: aka "Corey Minyard <minyard@acm.org>" [unknown]
# gpg: aka "Corey Minyard <corey@minyard.net>" [unknown]
# gpg: aka "Corey Minyard <minyard@mvista.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: FD0D 5CE6 7CE0 F59A 6688 2686 61F3 8C90 919B FF81

* remotes/cminyard/tags/for-qemu-6.1-2: (24 commits)
tests/qtest: add tests for MAX34451 device model
hw/misc: add MAX34451 device
tests/qtest: add tests for ADM1272 device model
hw/misc: add ADM1272 device
hw/i2c: add support for PMBus
ipmi/sim: fix watchdog_expired data type error in IPMIBmcSim struct
hw/i2c: Introduce i2c_start_recv() and i2c_start_send()
hw/i2c: Extract i2c_do_start_transfer() from i2c_start_transfer()
hw/i2c: Make i2c_start_transfer() direction argument a boolean
hw/i2c: Rename i2c_set_slave_address() -> i2c_slave_set_address()
hw/i2c: Remove confusing i2c_send_recv()
hw/misc/auxbus: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/misc/auxbus: Replace 'is_write' boolean by its value
hw/misc/auxbus: Explode READ_I2C / WRITE_I2C_MOT cases
hw/misc/auxbus: Fix MOT/classic I2C mode
hw/i2c/ppc4xx_i2c: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/i2c/ppc4xx_i2c: Add reference to datasheet
hw/display/sm501: Replace i2c_send_recv() by i2c_recv() & i2c_send()
hw/display/sm501: Simplify sm501_i2c_write() logic
hw/input/lm832x: Define TYPE_LM8323 in public header
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210709' into staging

target-arm queue:
* New machine type: stm32vldiscovery
* hw/intc/arm_gicv3_cpuif: Fix vir

Merge remote-tracking branch 'remotes/pmaydell/tags/pull-target-arm-20210709' into staging

target-arm queue:
* New machine type: stm32vldiscovery
* hw/intc/arm_gicv3_cpuif: Fix virtual irq number check in icv_[dir|eoir]_write
* hw/gpio/pl061: Honour Luminary PL061 PUR and PDR registers
* virt: Fix implementation of GPIO-based powerdown/shutdown mechanism
* Correct the encoding of MDCCSR_EL0 and DBGDSCRint
* hw/intc: Improve formatting of MEMTX_ERROR guest error message

# gpg: Signature made Fri 09 Jul 2021 17:09:10 BST
# gpg: using RSA key E1A5C593CD419DE28E8315CF3C2525ED14360CDE
# gpg: issuer "peter.maydell@linaro.org"
# gpg: Good signature from "Peter Maydell <peter.maydell@linaro.org>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@gmail.com>" [ultimate]
# gpg: aka "Peter Maydell <pmaydell@chiark.greenend.org.uk>" [ultimate]
# Primary key fingerprint: E1A5 C593 CD41 9DE2 8E83 15CF 3C25 25ED 1436 0CDE

* remotes/pmaydell/tags/pull-target-arm-20210709:
hw/intc: Improve formatting of MEMTX_ERROR guest error message
target/arm: Correct the encoding of MDCCSR_EL0 and DBGDSCRint
hw/arm/stellaris: Expand comment about handling of OLED chipselect
hw/gpio/pl061: Document a shortcoming in our implementation
hw/gpio/pl061: Convert to 3-phase reset and assert GPIO lines correctly on reset
hw/arm/virt: Make PL061 GPIO lines pulled low, not high
hw/gpio/pl061: Make pullup/pulldown of outputs configurable
hw/gpio/pl061: Honour Luminary PL061 PUR and PDR registers
hw/gpio/pl061: Document the interface of this device
hw/gpio/pl061: Add tracepoints for register read and write
hw/gpio/pl061: Clean up read/write offset handling logic
hw/gpio/pl061: Convert DPRINTF to tracepoints
hw/intc/arm_gicv3_cpuif: Fix virtual irq number check in icv_[dir|eoir]_write
tests/boot-serial-test: Add STM32VLDISCOVERY board testcase
docs/system: arm: Add stm32 boards description
stm32vldiscovery: Add the STM32VLDISCOVERY Machine
stm32f100: Add the stm32f100 SoC

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

hw/gpio/pl061: Convert to 3-phase reset and assert GPIO lines correctly on reset

The PL061 comes out of reset with all its lines configured as input,
which means they might need to be pu

hw/gpio/pl061: Convert to 3-phase reset and assert GPIO lines correctly on reset

The PL061 comes out of reset with all its lines configured as input,
which means they might need to be pulled to 0 or 1 depending on the
'pullups' and 'pulldowns' properties. Currently we do not assert
these lines on reset; they will only be set whenever the guest first
touches a register that triggers a call to pl061_update().

Convert the device to three-phase reset so we have a place where we
can safely call qemu_set_irq() to set the floating lines to their
correct values.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>

show more ...

hw/gpio/pl061: Honour Luminary PL061 PUR and PDR registers

The Luminary variant of the PL061 has registers GPIOPUR and GPIOPDR
which lets the guest configure whether the GPIO lines are p

hw/gpio/pl061: Honour Luminary PL061 PUR and PDR registers

The Luminary variant of the PL061 has registers GPIOPUR and GPIOPDR
which lets the guest configure whether the GPIO lines are pull-up,
pull-down, or truly floating. Instead of assuming all lines are pulled
high, honour the PUR and PDR registers.

For the plain PL061, continue to assume that lines have an external
pull-up resistor, as we did before.

The stellaris board actually relies on this behaviour -- the CD line
of the ssd0323 display device is connected to GPIO output C7, and it
is only because of a different bug which we're about to fix that we
weren't incorrectly driving this line high on reset and putting the
ssd0323 into data mode.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>

show more ...

hw/gpio/pl061: Add tracepoints for register read and write

Add tracepoints for reads and writes to the PL061 registers. This requires
restructuring pl061_read() to only return after the

hw/gpio/pl061: Add tracepoints for register read and write

Add tracepoints for reads and writes to the PL061 registers. This requires
restructuring pl061_read() to only return after the tracepoint, rather
than having lots of early-returns.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>

show more ...

hw/gpio/pl061: Convert DPRINTF to tracepoints

Convert the use of the DPRINTF debug macro in the PL061 model to
use tracepoints.

Signed-off-by: Peter Maydell <peter.maydell@linar

hw/gpio/pl061: Convert DPRINTF to tracepoints

Convert the use of the DPRINTF debug macro in the PL061 model to
use tracepoints.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <f4bug@amsat.org>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging

# gpg: Signature made Fri 04 Jun 2021 08:26:16 BST
# gpg: using RSA key EF04965B398D6211

Merge remote-tracking branch 'remotes/jasowang/tags/net-pull-request' into staging

# gpg: Signature made Fri 04 Jun 2021 08:26:16 BST
# gpg: using RSA key EF04965B398D6211
# gpg: Good signature from "Jason Wang (Jason Wang on RedHat) <jasowang@redhat.com>" [marginal]
# gpg: WARNING: This key is not certified with sufficiently trusted signatures!
# gpg: It is not certain that the signature belongs to the owner.
# Primary key fingerprint: 215D 46F4 8246 689E C77F 3562 EF04 965B 398D 6211

* remotes/jasowang/tags/net-pull-request:
MAINTAINERS: Added eBPF maintainers information.
docs: Added eBPF documentation.
virtio-net: Added eBPF RSS to virtio-net.
ebpf: Added eBPF RSS loader.
ebpf: Added eBPF RSS program.
net: Added SetSteeringEBPF method for NetClientState.
net/tap: Added TUNSETSTEERINGEBPF code.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging

Block layer patches

- NBD server: Fix crashes related to switching between AioContexts
- file-posix:

Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging

Block layer patches

- NBD server: Fix crashes related to switching between AioContexts
- file-posix: Workaround for discard/write_zeroes on buggy filesystems
- Follow-up fixes for the reopen vs. permission changes
- quorum: Fix error handling for flush
- block-copy: Refactor copy_range handling
- docs: Describe how to use 'null-co' block driver

# gpg: Signature made Wed 02 Jun 2021 14:44:15 BST
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6

* remotes/kevin/tags/for-upstream:
docs/secure-coding-practices: Describe how to use 'null-co' block driver
block-copy: refactor copy_range handling
block-copy: fix block_copy_task_entry() progress update
nbd/server: Use drained block ops to quiesce the server
block-backend: add drained_poll
block: improve permission conflict error message
block: simplify bdrv_child_user_desc()
block/vvfat: inherit child_vvfat_qcow from child_of_bds
block: improve bdrv_child_get_parent_desc()
block-backend: improve blk_root_get_parent_desc()
block: document child argument of bdrv_attach_child_common()
block/file-posix: Try other fallbacks after invalid FALLOC_FL_ZERO_RANGE
block/file-posix: Fix problem with fallocate(PUNCH_HOLE) on GPFS
block: drop BlockBackendRootState::read_only
block: drop BlockDriverState::read_only
block: consistently use bdrv_is_read_only()
block/vvfat: fix vvfat_child_perm crash
block/vvfat: child_vvfat_qcow: add .get_parent_aio_context, fix crash
qemu-io-cmds: assert that we don't have .perm requested in no-blk case
block/quorum: Provide .bdrv_co_flush instead of .bdrv_co_flush_to_disk

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2021-06-02' into staging

* Update the references to some doc files (use *.rst instead of *.txt)
* Bump minimum versio

Merge remote-tracking branch 'remotes/thuth-gitlab/tags/pull-request-2021-06-02' into staging

* Update the references to some doc files (use *.rst instead of *.txt)
* Bump minimum versions of some requirements after removing CentOS 7 support

# gpg: Signature made Wed 02 Jun 2021 08:12:18 BST
# gpg: using RSA key 27B88847EEE0250118F3EAB92ED9D774FE702DB5
# gpg: issuer "thuth@redhat.com"
# gpg: Good signature from "Thomas Huth <th.huth@gmx.de>" [full]
# gpg: aka "Thomas Huth <thuth@redhat.com>" [full]
# gpg: aka "Thomas Huth <huth@tuxfamily.org>" [full]
# gpg: aka "Thomas Huth <th.huth@posteo.de>" [unknown]
# Primary key fingerprint: 27B8 8847 EEE0 2501 18F3 EAB9 2ED9 D774 FE70 2DB5

* remotes/thuth-gitlab/tags/pull-request-2021-06-02:
configure: bump min required CLang to 6.0 / XCode 10.0
configure: bump min required GCC to 7.5.0
configure: bump min required glib version to 2.56
tests/docker: drop CentOS 7 container
tests/vm: convert centos VM recipe to CentOS 8
crypto: drop used conditional check
crypto: bump min gnutls to 3.5.18, dropping RHEL-7 support
crypto: bump min gcrypt to 1.8.0, dropping RHEL-7 support
crypto: drop back compatibility typedefs for nettle
crypto: bump min nettle to 3.4, dropping RHEL-7 support
patchew: move quick build job from CentOS 7 to CentOS 8 container
block/ssh: Bump minimum libssh version to 0.8.7
docs: fix references to docs/devel/s390-dasd-ipl.rst
docs: fix references to docs/specs/tpm.rst
docs: fix references to docs/devel/build-system.rst
docs: fix references to docs/devel/atomics.rst
docs: fix references to docs/devel/tracing.rst

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

docs: fix references to docs/devel/tracing.rst

Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.

We still h

docs: fix references to docs/devel/tracing.rst

Commit e50caf4a5c ("tracing: convert documentation to rST")
converted docs/devel/tracing.txt to docs/devel/tracing.rst.

We still have several references to the old file, so let's fix them
with the following command:

sed -i s/tracing.txt/tracing.rst/ $(git grep -l docs/devel/tracing.txt)

Signed-off-by: Stefano Garzarella <sgarzare@redhat.com>
Reviewed-by: Philippe Mathieu-Daudé <philmd@redhat.com>
Message-Id: <20210517151702.109066-2-sgarzare@redhat.com>
Signed-off-by: Thomas Huth <thuth@redhat.com>

show more ...

Merge remote-tracking branch 'remotes/nvme/tags/pull-nvme-20201102' into staging

nvme pull 2 Nov 2020

# gpg: Signature made Mon 02 Nov 2020 15:20:30 GMT
# gpg: us

Merge remote-tracking branch 'remotes/nvme/tags/pull-nvme-20201102' into staging

nvme pull 2 Nov 2020

# gpg: Signature made Mon 02 Nov 2020 15:20:30 GMT
# gpg: using RSA key DBC11D2D373B4A3755F502EC625156610A4F6CC0
# gpg: Good signature from "Keith Busch <kbusch@kernel.org>" [unknown]
# gpg: aka "Keith Busch <keith.busch@gmail.com>" [unknown]
# gpg: aka "Keith Busch <keith.busch@intel.com>" [unknown]
# gpg: WARNING: This key is not certified with a trusted signature!
# gpg: There is no indication that the signature belongs to the owner.
# Primary key fingerprint: DBC1 1D2D 373B 4A37 55F5 02EC 6251 5661 0A4F 6CC0

* remotes/nvme/tags/pull-nvme-20201102: (30 commits)
hw/block/nvme: fix queue identifer validation
hw/block/nvme: fix create IO SQ/CQ status codes
hw/block/nvme: fix prp mapping status codes
hw/block/nvme: report actual LBA data shift in LBAF
hw/block/nvme: add trace event for requests with non-zero status code
hw/block/nvme: add nsid to get/setfeat trace events
hw/block/nvme: reject io commands if only admin command set selected
hw/block/nvme: support for admin-only command set
hw/block/nvme: validate command set selected
hw/block/nvme: support per-namespace smart log
hw/block/nvme: fix log page offset check
hw/block/nvme: remove pointless rw indirection
hw/block/nvme: update nsid when registered
hw/block/nvme: change controller pci id
pci: allocate pci id for nvme
hw/block/nvme: support multiple namespaces
hw/block/nvme: refactor identify active namespace id list
hw/block/nvme: add support for sgl bit bucket descriptor
hw/block/nvme: add support for scatter gather lists
hw/block/nvme: harden cmb access
...

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/kraxel/tags/modules-20201029-pull-request' into staging

modules: build virtio-gpu-pci & virtio-vga modular.
modules: various bugfixes, mostly for ma

Merge remote-tracking branch 'remotes/kraxel/tags/modules-20201029-pull-request' into staging

modules: build virtio-gpu-pci & virtio-vga modular.
modules: various bugfixes, mostly for macos.

# gpg: Signature made Thu 29 Oct 2020 11:09:41 GMT
# gpg: using RSA key 4CB6D8EED3E87138
# gpg: Good signature from "Gerd Hoffmann (work) <kraxel@redhat.com>" [full]
# gpg: aka "Gerd Hoffmann <gerd@kraxel.org>" [full]
# gpg: aka "Gerd Hoffmann (private) <kraxel@gmail.com>" [full]
# Primary key fingerprint: A032 8CFF B93A 17A7 9901 FE7D 4CB6 D8EE D3E8 7138

* remotes/kraxel/tags/modules-20201029-pull-request:
modules: turn off lazy binding
modules: unbreak them on macos
virtio-gpu: only compile virtio-gpu-3d.c for CONFIG_VIRGL=y
virtio-gpu: add virtio-vga module
virtio-gpu: add virtio-gpu-pci module

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/berrange-gitlab/tags/misc-next-pull-request' into staging

Misc fixes

* Improve socket cnnection failure error reporting
* Fix LGPL versio

Merge remote-tracking branch 'remotes/berrange-gitlab/tags/misc-next-pull-request' into staging

Misc fixes

* Improve socket cnnection failure error reporting
* Fix LGPL version number

# gpg: Signature made Thu 29 Oct 2020 10:00:47 GMT
# gpg: using RSA key DAF3A6FDB26B62912D0E8E3FBE86EBB415104FDF
# gpg: Good signature from "Daniel P. Berrange <dan@berrange.com>" [full]
# gpg: aka "Daniel P. Berrange <berrange@redhat.com>" [full]
# Primary key fingerprint: DAF3 A6FD B26B 6291 2D0E 8E3F BE86 EBB4 1510 4FDF

* remotes/berrange-gitlab/tags/misc-next-pull-request:
util: include the target address in socket connect failures
io: Don't use '#' flag of printf format
authz: Fix Lesser GPL version number
crypt: Fix Lesser GPL version number
io: Fix Lesser GPL version number

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/mcayland/tags/qemu-sparc-20201028' into staging

qemu-sparc queue

# gpg: Signature made Wed 28 Oct 2020 08:17:23 GMT
# gpg: u

Merge remote-tracking branch 'remotes/mcayland/tags/qemu-sparc-20201028' into staging

qemu-sparc queue

# gpg: Signature made Wed 28 Oct 2020 08:17:23 GMT
# gpg: using RSA key CC621AB98E82200D915CC9C45BC2C56FAE0F321F
# gpg: issuer "mark.cave-ayland@ilande.co.uk"
# gpg: Good signature from "Mark Cave-Ayland <mark.cave-ayland@ilande.co.uk>" [full]
# Primary key fingerprint: CC62 1AB9 8E82 200D 915C C9C4 5BC2 C56F AE0F 321F

* remotes/mcayland/tags/qemu-sparc-20201028:
hw/pci-host/sabre: Simplify code initializing variable once
hw/pci-host/sabre: Remove superfluous address range check
hw/pci-host/sabre: Update documentation link
sabre: increase number of PCI bus IRQs from 32 to 64
hw/display/tcx: Allow 64-bit accesses to framebuffer stippler and blitter
sabre: don't call sysbus_mmio_map() in sabre_realize()
sparc32-ledma: don't reference nd_table directly within the device
sparc32-espdma: use object_initialize_child() for esp child object
sparc32-ledma: use object_initialize_child() for lance child object
sparc32-dma: use object_initialize_child() for espdma and ledma child objects

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/rth-gitlab/tags/pull-tcg-20201027' into staging

Optimize across branches.
Add logging for cpu_io_recompile.

# gpg: Signature made Tue 27 Oc

Merge remote-tracking branch 'remotes/rth-gitlab/tags/pull-tcg-20201027' into staging

Optimize across branches.
Add logging for cpu_io_recompile.

# gpg: Signature made Tue 27 Oct 2020 16:48:50 GMT
# gpg: using RSA key 7A481E78868B4DB6A85A05C064DF38E8AF7E215F
# gpg: issuer "richard.henderson@linaro.org"
# gpg: Good signature from "Richard Henderson <richard.henderson@linaro.org>" [full]
# Primary key fingerprint: 7A48 1E78 868B 4DB6 A85A 05C0 64DF 38E8 AF7E 215F

* remotes/rth-gitlab/tags/pull-tcg-20201027:
accel/tcg: Add CPU_LOG_EXEC tracing for cpu_io_recompile()
tcg/optimize: Flush data at labels not TCG_OPF_BB_END
tcg: Do not kill globals at conditional branches

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-5.2-pull-request' into staging

Pull request trivial branch 20201027

# gpg: Signature made Tue 27 Oct 2020 16:29

Merge remote-tracking branch 'remotes/vivier2/tags/trivial-branch-for-5.2-pull-request' into staging

Pull request trivial branch 20201027

# gpg: Signature made Tue 27 Oct 2020 16:29:47 GMT
# gpg: using RSA key CD2F75DDC8E3A4DC2E4F5173F30C38BD3F2FBE3C
# gpg: issuer "laurent@vivier.eu"
# gpg: Good signature from "Laurent Vivier <lvivier@redhat.com>" [full]
# gpg: aka "Laurent Vivier <laurent@vivier.eu>" [full]
# gpg: aka "Laurent Vivier (Red Hat) <lvivier@redhat.com>" [full]
# Primary key fingerprint: CD2F 75DD C8E3 A4DC 2E4F 5173 F30C 38BD 3F2F BE3C

* remotes/vivier2/tags/trivial-branch-for-5.2-pull-request:
CHANGELOG: remove disused file
qdev: Fix two typos
scripts/qmp: delete 'qmp' script
cryptodev: Fix Lesser GPL version number
io: Fix Lesser GPL version number
cpus: Drop declaration of cpu_remove()
Makefile: Add *.[ch].inc files to cscope/ctags/TAGS
elf2dmp: Fix memory leak on main() error paths

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...

Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging

Block layer patches:

- qcow2: Skip copy-on-write when allocating a zero cluster
- qemu-img: add suppo

Merge remote-tracking branch 'remotes/kevin/tags/for-upstream' into staging

Block layer patches:

- qcow2: Skip copy-on-write when allocating a zero cluster
- qemu-img: add support for rate limit in qemu-img convert/commit
- Fix deadlock when deleting a block node during drain_all

# gpg: Signature made Tue 27 Oct 2020 15:14:07 GMT
# gpg: using RSA key DC3DEB159A9AF95D3D7456FE7F09B272C88F2FD6
# gpg: issuer "kwolf@redhat.com"
# gpg: Good signature from "Kevin Wolf <kwolf@redhat.com>" [full]
# Primary key fingerprint: DC3D EB15 9A9A F95D 3D74 56FE 7F09 B272 C88F 2FD6

* remotes/kevin/tags/for-upstream:
block: End quiescent sections when a BDS is deleted
qcow2: Skip copy-on-write when allocating a zero cluster
qcow2: Report BDRV_BLOCK_ZERO more accurately in bdrv_co_block_status()
qemu-img: add support for rate limit in qemu-img convert
qemu-img: add support for rate limit in qemu-img commit

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...