hw/gpio: Handle clock migration in STM32L4x5 gpios

STM32L4x5 GPIO wasn't migrating its clock.

Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@l

hw/gpio: Handle clock migration in STM32L4x5 gpios

STM32L4x5 GPIO wasn't migrating its clock.

Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-ID: <20240507185854.34572-3-ines.varhol@telecom-paris.fr>
Signed-off-by: Philippe Mathieu-Daudé <philmd@linaro.org>

show more ...

hw, target: Add ResetType argument to hold and exit phase methods

We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the call

hw, target: Add ResetType argument to hold and exit phase methods

We pass a ResetType argument to the Resettable class enter
phase method, but we don't pass it to hold and exit, even though
the callsites have it readily available. This means that if
a device cared about the ResetType it would need to record it
in the enter phase method to use later on. Pass the type to
all three of the phase methods to avoid having to do that.

Commit created with

for dir in hw target include; do \
spatch --macro-file scripts/cocci-macro-file.h \
--sp-file scripts/coccinelle/reset-type.cocci \
--keep-comments --smpl-spacing --in-place \
--include-headers --dir $dir; done

and no manual edits.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Edgar E. Iglesias <edgar.iglesias@amd.com>
Reviewed-by: Richard Henderson <richard.henderson@linaro.org>
Reviewed-by: Luc Michel <luc.michel@amd.com>
Message-id: 20240412160809.1260625-5-peter.maydell@linaro.org

show more ...

hw/gpio: Implement STM32L4x5 GPIO

Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externa

hw/gpio: Implement STM32L4x5 GPIO

Features supported :
- the 8 STM32L4x5 GPIOs are initialized with their reset values
(except IDR, see below)
- input mode : setting a pin in input mode "externally" (using input
irqs) results in an out irq (transmitted to SYSCFG)
- output mode : setting a bit in ODR sets the corresponding out irq
(if this line is configured in output mode)
- pull-up, pull-down
- push-pull, open-drain

Difference with the real GPIOs :
- Alternate Function and Analog mode aren't implemented :
pins in AF/Analog behave like pins in input mode
- floating pins stay at their last value
- register IDR reset values differ from the real one :
values are coherent with the other registers reset values
and the fact that AF/Analog modes aren't implemented
- setting I/O output speed isn't supported
- locking port bits isn't supported
- ADC function isn't supported
- GPIOH has 16 pins instead of 2 pins
- writing to registers LCKR, AFRL, AFRH and ASCR is ineffective

Signed-off-by: Arnaud Minier <arnaud.minier@telecom-paris.fr>
Signed-off-by: Inès Varhol <ines.varhol@telecom-paris.fr>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Acked-by: Alistair Francis <alistair.francis@wdc.com>
Message-id: 20240305210444.310665-2-ines.varhol@telecom-paris.fr
Signed-off-by: Peter Maydell <peter.maydell@linaro.org>

show more ...