hw/arm/mps3r: Add remaining devices

Add the remaining devices (or unimplemented-device stubs) for
this board: SPI controllers, SCC, FPGAIO, I2S, RTC, the
QSPI write-config block, and ethernet.

Sign

hw/arm/mps3r: Add remaining devices

Add the remaining devices (or unimplemented-device stubs) for
this board: SPI controllers, SCC, FPGAIO, I2S, RTC, the
QSPI write-config block, and ethernet.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-13-peter.maydell@linaro.org

show more ...

hw/arm/mps3r: Add GPIO, watchdog, dual-timer, I2C devices

Add the GPIO, watchdog, dual-timer and I2C devices to the mps3-an536
board. These are all simple devices that just need to be created and
w

hw/arm/mps3r: Add GPIO, watchdog, dual-timer, I2C devices

Add the GPIO, watchdog, dual-timer and I2C devices to the mps3-an536
board. These are all simple devices that just need to be created and
wired up.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-12-peter.maydell@linaro.org

show more ...

hw/arm/mps3r: Add UARTs

This board has a lot of UARTs: there is one UART per CPU in the
per-CPU peripheral part of the address map, whose interrupts are
connected as per-CPU interrupt lines. Then t

hw/arm/mps3r: Add UARTs

This board has a lot of UARTs: there is one UART per CPU in the
per-CPU peripheral part of the address map, whose interrupts are
connected as per-CPU interrupt lines. Then there are 4 UARTs in the
normal part of the peripheral space, whose interrupts are shared
peripheral interrupts.

Connect and wire them all up; this involves some OR gates where
multiple overflow interrupts are wired into one GIC input.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-11-peter.maydell@linaro.org

show more ...

hw/arm/mps3r: Add CPUs, GIC, and per-CPU RAM

Create the CPUs, the GIC, and the per-CPU RAM block for
the mps3-an536 board.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 202402

hw/arm/mps3r: Add CPUs, GIC, and per-CPU RAM

Create the CPUs, the GIC, and the per-CPU RAM block for
the mps3-an536 board.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Message-id: 20240206132931.38376-10-peter.maydell@linaro.org

show more ...

hw/arm/mps3r: Initial skeleton for mps3-an536 board

The AN536 is another FPGA image for the MPS3 development board. Unlike
the existing FPGA images we already model, this board uses a Cortex-R
famil

hw/arm/mps3r: Initial skeleton for mps3-an536 board

The AN536 is another FPGA image for the MPS3 development board. Unlike
the existing FPGA images we already model, this board uses a Cortex-R
family CPU, and it does not use any equivalent to the M-profile
"Subsystem for Embedded" SoC-equivalent that we model in hw/arm/armsse.c.
It's therefore more convenient for us to model it as a completely
separate C file.

This commit adds the basic skeleton of the board model, and the
code to create all the RAM and ROM. We assume that we're probably
going to want to add more images in future, so use the same
base class/subclass setup that mps2-tz.c uses, even though at
the moment there's only a single subclass.

Following commits will add the CPUs and the peripherals.

Signed-off-by: Peter Maydell <peter.maydell@linaro.org>
Reviewed-by: Philippe Mathieu-Daudé <philmd@linaro.org>
Message-id: 20240206132931.38376-9-peter.maydell@linaro.org

show more ...