control:p10bmc: Force retry on OCC active group

Thirty seconds after fan control has started, check again if the service
hosting the OccActive property can be found, and release the existing
target

control:p10bmc: Force retry on OCC active group

Thirty seconds after fan control has started, check again if the service
hosting the OccActive property can be found, and release the existing
target hold if there was one from when the set_target_on_missing_owner
action originally ran.

Thirty seconds was chosen to be far out enough to let thing settle down
a bit.

This is to work around a problem where the OCC service wasn't running
the first time fan control checked, and then it somehow missed the
NameOwnerChanged signal so the target hold from the
set_target_on_missing_owner action was permanently set.

There is also a change to switch the order of the triggers in the
'service(s) missing' action to add the NameOwnerChanged match before
checking if the name has an owner, closing a very small window where it
was possible the signal came in after the check but before the match was
added.

Tested:
By adding traces, viewed that the new action ran 30 seconds after
startup, and that the order of the triggers was changed.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: I5a74a09a066757207fbf9a598aa7282aae2b58ce

show more ...

control:ibm,Bonnell: Add hot PCIe card

Add the 'GTO' PCIe card to the list of hot PCIe cards, and add floor
values for its floor index.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: I

control:ibm,Bonnell: Add hot PCIe card

Add the 'GTO' PCIe card to the list of hot PCIe cards, and add floor
values for its floor index.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: Ie2863a08cdf9c85ca5e6c25d56d4cc367da60218

show more ...

control:Bonnell: Increase ambient values by 4.5

Increase any values referencing the ambient temperature by 4.5 degrees
to account for the fact that the actual temperature is 4.5 degrees
higher than

control:Bonnell: Increase ambient values by 4.5

Increase any values referencing the ambient temperature by 4.5 degrees
to account for the fact that the actual temperature is 4.5 degrees
higher than what the sensor shows.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: I2441c68676a716f7d5324b81bb48102187ab600f

show more ...

control:Bonnell: Remove hot PCIe cards

It turns out that Bonnell doesn't have any 'hot' pcie cards, so the
floor can just be based on ambient and altitude.

This commit removes the cards from pcie_c

control:Bonnell: Remove hot PCIe cards

It turns out that Bonnell doesn't have any 'hot' pcie cards, so the
floor can just be based on ambient and altitude.

This commit removes the cards from pcie_cards.json and removes any PCIe
floor index values from the mapped_floor action in events.json. It
still leaves the infrastructure to keep things more common with the
other IBM systems, and to make it easier to add in a card if/when a hot
one comes into plan.

There is also a code update needed to allow an empty pcie_cards.json
file.

Tested:
Floors are set appropriately based on the altitude and ambient.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: I10e6904602c7abf61121f7c610059f164405b758

show more ...

control:Bonnell: Config updates

The following updates were made to the Bonnell fan control config:
- Change max RPMs to 17000 from 18000
- The fans could never actually hit 18000
- Add the real PC

control:Bonnell: Config updates

The following updates were made to the Bonnell fan control config:
- Change max RPMs to 17000 from 18000
- The fans could never actually hit 18000
- Add the real PCIe card list
- Update the floor table and the associated parameters
- Some unused floor indices are left in the table to make
it easier for future expansion.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: Ia7f4627f9458322e250452e67f330ede063c7efe

show more ...

control:Bonnell: Update dram temp thresholds

Move the dram temp range to 64-61 from 68-65.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: I0f3847e70e59e8cd15e5934827c9d3df23530bb6

control:config:ibm: Use count_state_floor delay

Add a 5 second delay to the count_state_floor action that watches for
non functional sensors to all IBM configurations. With this change, a
sensor ha

control:config:ibm: Use count_state_floor delay

Add a 5 second delay to the count_state_floor action that watches for
non functional sensors to all IBM configurations. With this change, a
sensor has to be nonfunctional for at least 5 seconds for the floor to
change.

This is being done because the NVMe temperature sensors would briefly be
set to nonfunctional when a drive is removed.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: I6fa70f2551c11b2cfe8ee4696b6d72d57a3a7bd5

show more ...

cnfgs:p10bmc: Rename the IBM config directories

Due to the fan applications now using the
xyz.openbmc_project.Inventory.Decorator.Compatible interface instead of
the xyz.openbmc_project.Configuratio

cnfgs:p10bmc: Rename the IBM config directories

Due to the fan applications now using the
xyz.openbmc_project.Inventory.Decorator.Compatible interface instead of
the xyz.openbmc_project.Configuration.IBMCompatibleSystem one, the names
of the systems have changed as the new interface uses a different
property value format.

Rename all of the directories that mirror those property names to the new
ones.

Signed-off-by: Matt Spinler <spinler@us.ibm.com>
Change-Id: Ie541d15b47a155e88800fb7def76c0e8fbd8182b

show more ...