treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 149

Based on 1 normalized pattern(s):

licensed under the gpl 2 or later

extracted by the scancode license scanner the SPDX license

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 149

Based on 1 normalized pattern(s):

licensed under the gpl 2 or later

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 82 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

ASoC: adav80x: Split SPI and I2C code into different modules

There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra ca

ASoC: adav80x: Split SPI and I2C code into different modules

There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register. Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus drive
to continue without problems if one of them fails.

This patch splits the ADAV80X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>

show more ...

ASoC: Add ADAV80x codec driver

This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.co

ASoC: Add ADAV80x codec driver

This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 149

Based on 1 normalized pattern(s):

licensed under the gpl 2 or later

extracted by the scancode license s

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 149

Based on 1 normalized pattern(s):

licensed under the gpl 2 or later

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 82 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190524100845.150836982@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

ASoC: adav80x: Split SPI and I2C code into different modules

There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We nee

ASoC: adav80x: Split SPI and I2C code into different modules

There are a few known (minor) problems with having the support code for both I2C
and SPI in the same module:
* We need to be extra careful to make sure to not build the driver into the
kernel if one of the subsystems is build as a module (Currently only I2C
can be build as a module).
* The module init path error handling is rather ugly. E.g. what should be
done if either the SPI or the I2C driver fails to register. Most drivers
that implement SPI and I2C in the same module currently fallback to
undefined behavior in that case. Splitting the the driver into two
modules, one for each bus, allows the registration of the other bus drive
to continue without problems if one of them fails.

This patch splits the ADAV80X driver into 3 modules. One core module that
implements the device logic, but is independent of the bus method used. And one
module for SPI and I2C each that registers the drivers and sets up the regmap
struct for the bus.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Signed-off-by: Mark Brown <broonie@linaro.org>

show more ...

ASoC: Add ADAV80x codec driver

This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam

ASoC: Add ADAV80x codec driver

This patch adds support for the Analog Devices ADAV801 and ADAV803 audio codec.

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Acked-by: Liam Girdwood <lrg@ti.com>
Signed-off-by: Mark Brown <broonie@opensource.wolfsonmicro.com>

show more ...