|
Revision tags: v5.3.5, v5.3.4, v5.3.3, v5.3.2, v5.3.1, v5.3, v5.2.14, v5.3-rc8, v5.2.13, v5.2.12, v5.2.11, v5.2.10 |
|
| #
15ede970 |
| 23-Aug-2019 |
Ondrej Jirman <megous@megous.com> |
arm64: dts: allwinner: orange-pi-3: Enable WiFi
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is
arm64: dts: allwinner: orange-pi-3: Enable WiFi
Orange Pi 3 has AP6256 WiFi/BT module. WiFi part of the module is called
bcm43356 and can be used with the brcmfmac driver. The module is powered by
the two always on regulators (not AXP805).
WiFi uses a PG port with 1.8V voltage level signals. SoC needs to be
configured so that it sets up an 1.8V input bias on this port. This is done
by the pio driver by reading the vcc-pg-supply voltage.
You'll need a fw_bcm43456c5_ag.bin firmware file and nvram.txt
configuration that can be found in the Xulongs's repository for H6:
https://github.com/orangepi-xunlong/OrangePiH6_external/tree/master/ap6256
Mainline brcmfmac driver expects the firmware and nvram at the following
paths relative to the firmware directory:
brcm/brcmfmac43456-sdio.bin
brcm/brcmfmac43456-sdio.txt
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
show more ...
|
|
Revision tags: v5.2.9, v5.2.8, v5.2.7 |
|
| #
802cbe1b |
| 06-Aug-2019 |
Ondrej Jirman <megous@megous.com> |
arm64: dts: allwinner: orange-pi-3: Enable HDMI output
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we nee
arm64: dts: allwinner: orange-pi-3: Enable HDMI output
Orange Pi 3 has a DDC_CEC_EN signal connected to PH2, that enables the DDC
I2C bus voltage shifter. Before EDID can be read, we need to pull PH2 high.
This is realized by the ddc-en-gpios property.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
show more ...
|
|
Revision tags: v5.2.6, v5.2.5, v5.2.4, v5.2.3, v5.2.2, v5.2.1, v5.2, v5.1.16, v5.1.15, v5.1.14, v5.1.13, v5.1.12, v5.1.11, v5.1.10, v5.1.9, v5.1.8, v5.1.7, v5.1.6, v5.1.5, v5.1.4, v5.1.3, v5.1.2, v5.1.1, v5.0.14, v5.1, v5.0.13, v5.0.12, v5.0.11, v5.0.10, v5.0.9, v5.0.8 |
|
| #
8fe62f12 |
| 08-Apr-2019 |
Ondrej Jirman <megous@megous.com> |
arm64: dts: allwinner: h6: Add Orange Pi 3 DTS
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64
arm64: dts: allwinner: h6: Add Orange Pi 3 DTS
Orange Pi 3 is a H6 based SBC made by Xulong, released in January 2019. It
has the following features:
- Allwinner H6 quad-core 64-bit ARM Cortex-A53
- GPU Mali-T720
- 1GB or 2GB LPDDR3 RAM
- AXP805 PMIC
- AP6256 Wifi/BT 5.0
- USB 2.0 host port (A)
- USB 2.0 micro usb, OTG
- USB 3.0 Host + 4 port USB hub (GL3510)
- Gigabit Ethernet (Realtek RTL8211E phy)
- HDMI 2.0 port
- soldered eMMC (optional)
- 3x LED (one is on the bottom)
- microphone
- audio jack
- PCIe
Add basic support for the board.
Signed-off-by: Ondrej Jirman <megous@megous.com>
Signed-off-by: Maxime Ripard <maxime.ripard@bootlin.com>
show more ...
|