Revert "bridge: Add extack warning when enabling STP in netns."

This reverts commit 56a16035bb6effb37177867cea94c13a8382f745.

Since the previous commit, STP works on bridge in netns.

# unshare -

Revert "bridge: Add extack warning when enabling STP in netns."

This reverts commit 56a16035bb6effb37177867cea94c13a8382f745.

Since the previous commit, STP works on bridge in netns.

# unshare -n
# ip link add br0 type bridge
# ip link add veth0 type veth peer name veth1

# ip link set veth0 master br0 up
[ 50.558135] br0: port 1(veth0) entered blocking state
[ 50.558366] br0: port 1(veth0) entered disabled state
[ 50.558798] veth0: entered allmulticast mode
[ 50.564401] veth0: entered promiscuous mode

# ip link set veth1 master br0 up
[ 54.215487] br0: port 2(veth1) entered blocking state
[ 54.215657] br0: port 2(veth1) entered disabled state
[ 54.215848] veth1: entered allmulticast mode
[ 54.219577] veth1: entered promiscuous mode

# ip link set br0 type bridge stp_state 1
# ip link set br0 up
[ 61.960726] br0: port 2(veth1) entered blocking state
[ 61.961097] br0: port 2(veth1) entered listening state
[ 61.961495] br0: port 1(veth0) entered blocking state
[ 61.961653] br0: port 1(veth0) entered listening state
[ 63.998835] br0: port 2(veth1) entered blocking state
[ 77.437113] br0: port 1(veth0) entered learning state
[ 86.653501] br0: received packet on veth0 with own address as source address (addr:6e:0f:e7:6f:5f:5f, vlan:0)
[ 92.797095] br0: port 1(veth0) entered forwarding state
[ 92.797398] br0: topology change detected, propagating

Let's remove the warning.

Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>

show more ...

bridge: Add extack warning when enabling STP in netns.

When we create an L2 loop on a bridge in netns, we will see packets storm
even if STP is enabled.

# unshare -n
# ip link add br0 type brid

bridge: Add extack warning when enabling STP in netns.

When we create an L2 loop on a bridge in netns, we will see packets storm
even if STP is enabled.

# unshare -n
# ip link add br0 type bridge
# ip link add veth0 type veth peer name veth1
# ip link set veth0 master br0 up
# ip link set veth1 master br0 up
# ip link set br0 type bridge stp_state 1
# ip link set br0 up
# sleep 30
# ip -s link show br0
2: br0: <BROADCAST,MULTICAST,UP,LOWER_UP> mtu 1500 qdisc noqueue state UP mode DEFAULT group default qlen 1000
link/ether b6:61:98:1c:1c:b5 brd ff:ff:ff:ff:ff:ff
RX: bytes packets errors dropped missed mcast
956553768 12861249 0 0 0 12861249 <-. Keep
TX: bytes packets errors dropped carrier collsns | increasing
1027834 11951 0 0 0 0 <-' rapidly

This is because llc_rcv() drops all packets in non-root netns and BPDU
is dropped.

Let's add extack warning when enabling STP in netns.

# unshare -n
# ip link add br0 type bridge
# ip link set br0 type bridge stp_state 1
Warning: bridge: STP does not work in non-root netns.

Note this commit will be reverted later when we namespacify the whole LLC
infra.

Fixes: e730c15519d0 ("[NET]: Make packet reception network namespace safe")
Suggested-by: Harry Coin <hcoin@quietfountain.com>
Link: https://lore.kernel.org/netdev/0f531295-e289-022d-5add-5ceffa0df9bc@quietfountain.com/
Suggested-by: Ido Schimmel <idosch@idosch.org>
Signed-off-by: Kuniyuki Iwashima <kuniyu@amazon.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: use eth_hw_addr_set()

Convert sw drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():

@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)

S

net: use eth_hw_addr_set()

Convert sw drivers from memcpy(... ETH_ADDR) to eth_hw_addr_set():

@@
expression dev, np;
@@
- memcpy(dev->dev_addr, np, ETH_ALEN)
+ eth_hw_addr_set(dev, np)

Signed-off-by: Jakub Kicinski <kuba@kernel.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: remove newlines in NL_SET_ERR_MSG_MOD

The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have

net: remove newlines in NL_SET_ERR_MSG_MOD

The NL_SET_ERR_MSG_MOD macro is used to report a string describing an
error message to userspace via the netlink extended ACK structure. It
should not have a trailing newline.

Add a cocci script which catches cases where the newline marker is
present. Using this script, fix the handful of cases which accidentally
included a trailing new line.

I couldn't figure out a way to get a patch mode working, so this script
only implements context, report, and org.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jakub Kicinski <kuba@kernel.org>
Cc: Andy Whitcroft <apw@canonical.com>
Cc: Joe Perches <joe@perches.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: Add checks for enabling the STP.

It is not possible to have the MRP and STP running at the same time on the
bridge, therefore add check when enabling the STP to check if MRP is already

net: bridge: Add checks for enabling the STP.

It is not possible to have the MRP and STP running at the same time on the
bridge, therefore add check when enabling the STP to check if MRP is already
enabled. In that case return error.

Reviewed-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

net: bridge: optimize backup_port fdb convergence

We can optimize the fdb convergence when a backup_port is present by not
immediately flushing the entries of the stopped port since traffic for
thos

net: bridge: optimize backup_port fdb convergence

We can optimize the fdb convergence when a backup_port is present by not
immediately flushing the entries of the stopped port since traffic for
those entries will flow towards the backup_port.

There are 2 cases specifically that benefit most:
- when the stopped port comes up before the entries expire by themselves
- when there's an external entry refresh and they're kept while the
backup_port is operating (e.g. mlag)

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: add notifications for the bridge dev on vlan change

Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic b

net: bridge: add notifications for the bridge dev on vlan change

Currently the bridge device doesn't generate any notifications upon vlan
modifications on itself because it doesn't use the generic bridge
notifications.
With the recent changes we know if anything was modified in the vlan config
thus we can generate a notification when necessary for the bridge device
so add support to br_ifinfo_notify() similar to how other combined
functions are done - if port is present it takes precedence, otherwise
notify about the bridge. I've explicitly marked the locations where the
notification should be always for the port by setting bridge to NULL.
I've also taken the liberty to rearrange each modified function's local
variables in reverse xmas tree as well.

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: start hello timer only if device is up

When the transition of NO_STP -> KERNEL_STP was fixed by always calling
mod_timer in br_stp_start, it introduced a new regression which causes
the

net: bridge: start hello timer only if device is up

When the transition of NO_STP -> KERNEL_STP was fixed by always calling
mod_timer in br_stp_start, it introduced a new regression which causes
the timer to be armed even when the bridge is down, and since we stop
the timers in its ndo_stop() function, they never get disabled if the
device is destroyed before it's upped.

To reproduce:
$ while :; do ip l add br0 type bridge hello_time 100; brctl stp br0 on;
ip l del br0; done;

CC: Xin Long <lucien.xin@gmail.com>
CC: Ivan Vecera <cera@cera.cz>
CC: Sebastian Ott <sebott@linux.vnet.ibm.com>
Reported-by: Sebastian Ott <sebott@linux.vnet.ibm.com>
Fixes: 6d18c732b95c ("bridge: start hello_timer when enabling KERNEL_STP in br_stp_start")
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: fix hello and hold timers starting/stopping

Current bridge code incorrectly handles starting/stopping of hello and
hold timers during STP enable/disable.

1. Timers are stopped in br_stp_sta

bridge: fix hello and hold timers starting/stopping

Current bridge code incorrectly handles starting/stopping of hello and
hold timers during STP enable/disable.

1. Timers are stopped in br_stp_start() during NO_STP->USER_STP
transition. The timers are already stopped in NO_STP state so
this is confusing no-op.

2. During USER_STP->NO_STP transition the timers are started. This
does not make sense and is confusion because the timer should not be
active in NO_STP state.

Cc: davem@davemloft.net
Cc: sashok@cumulusnetworks.com
Cc: stephen@networkplumber.org
Cc: bridge@lists.linux-foundation.org
Cc: lucien.xin@gmail.com
Cc: nikolay@cumulusnetworks.com
Signed-off-by: Ivan Vecera <cera@cera.cz>
Reviewed-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: start hello_timer when enabling KERNEL_STP in br_stp_start

Since commit 76b91c32dd86 ("bridge: stp: when using userspace stp stop
kernel hello and hold timers"), bridge would not start hello

bridge: start hello_timer when enabling KERNEL_STP in br_stp_start

Since commit 76b91c32dd86 ("bridge: stp: when using userspace stp stop
kernel hello and hold timers"), bridge would not start hello_timer if
stp_enabled is not KERNEL_STP when br_dev_open.

The problem is even if users set stp_enabled with KERNEL_STP later,
the timer will still not be started. It causes that KERNEL_STP can
not really work. Users have to re-ifup the bridge to avoid this.

This patch is to fix it by starting br->hello_timer when enabling
KERNEL_STP in br_stp_start.

As an improvement, it's also to start hello_timer again only when
br->stp_enabled is KERNEL_STP in br_hello_timer_expired, there is
no reason to start the timer again when it's NO_STP.

Fixes: 76b91c32dd86 ("bridge: stp: when using userspace stp stop kernel hello and hold timers")
Reported-by: Haidong Li <haili@redhat.com>
Signed-off-by: Xin Long <lucien.xin@gmail.com>
Acked-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Reviewed-by: Ivan Vecera <cera@cera.cz>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: move to workqueue gc

Move the fdb garbage collector to a workqueue which fires at least 10
milliseconds apart and cleans chain by chain allowing for other tasks
to run in the meantime. When

bridge: move to workqueue gc

Move the fdb garbage collector to a workqueue which fires at least 10
milliseconds apart and cleans chain by chain allowing for other tasks
to run in the meantime. When having thousands of fdbs the system is much
more responsive. Most importantly remove the need to check if the
matched entry has expired in __br_fdb_get that causes false-sharing and
is completely unnecessary if we cleanup entries, at worst we'll get 10ms
of traffic for that entry before it gets deleted.

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: add helper to set topology change

Add a __br_set_topology_change helper to set the topology change value.

This can be later extended to add actions when the topology change flag
is set

net: bridge: add helper to set topology change

Add a __br_set_topology_change helper to set the topology change value.

This can be later extended to add actions when the topology change flag
is set or cleared.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: add helper to offload ageing time

The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time fr

net: bridge: add helper to offload ageing time

The SWITCHDEV_ATTR_ID_BRIDGE_AGEING_TIME switchdev attr is actually set
when initializing a bridge port, and when configuring the bridge ageing
time from ioctl/netlink/sysfs.

Add a __set_ageing_time helper to offload the ageing time to physical
switches, and add the SWITCHDEV_F_DEFER flag since it can be called
under bridge lock.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: add helper to call /sbin/bridge-stp

If /sbin/bridge-stp is available on the system, bridge tries to execute
it instead of the kernel implementation when starting/stopping STP.

If anyth

net: bridge: add helper to call /sbin/bridge-stp

If /sbin/bridge-stp is available on the system, bridge tries to execute
it instead of the kernel implementation when starting/stopping STP.

If anything goes wrong with /sbin/bridge-stp, bridge silently falls back
to kernel STP, making hard to debug userspace STP.

This patch adds a br_stp_call_user helper to start/stop userspace STP
and debug errors from the program: abnormal exit status is stored in the
lower byte and normal exit status is stored in higher byte.

Below is a simple example on a kernel with dynamic debug enabled:

# ln -s /bin/false /sbin/bridge-stp
# brctl stp br0 on
br0: failed to start userspace STP (256)
# dmesg
br0: /sbin/bridge-stp exited with code 1
br0: failed to start userspace STP (256)
br0: using kernel STP

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: fix br_stp_enable_bridge comment

br_stp_enable_bridge() does take the br->lock spinlock. Fix its wrongly
pasted comment and use the same as br_stp_disable_bridge().

Signed-off-by: Vivi

net: bridge: fix br_stp_enable_bridge comment

br_stp_enable_bridge() does take the br->lock spinlock. Fix its wrongly
pasted comment and use the same as br_stp_disable_bridge().

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: log port STP state on change

Remove the shared br_log_state function and print the info directly in
br_set_state, where the net_bridge_port state is actually changed.

Signed-off-by: Vi

net: bridge: log port STP state on change

Remove the shared br_log_state function and print the info directly in
br_set_state, where the net_bridge_port state is actually changed.

Signed-off-by: Vivien Didelot <vivien.didelot@savoirfairelinux.com>
Acked-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: Only call /sbin/bridge-stp for the initial network namespace

[I stole this patch from Eric Biederman. He wrote:]

> There is no defined mechanism to pass network namespace information
> into

bridge: Only call /sbin/bridge-stp for the initial network namespace

[I stole this patch from Eric Biederman. He wrote:]

> There is no defined mechanism to pass network namespace information
> into /sbin/bridge-stp therefore don't even try to invoke it except
> for bridge devices in the initial network namespace.
>
> It is possible for unprivileged users to cause /sbin/bridge-stp to be
> invoked for any network device name which if /sbin/bridge-stp does not
> guard against unreasonable arguments or being invoked twice on the
> same network device could cause problems.

[Hannes: changed patch using netns_eq]

Cc: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Eric W. Biederman <ebiederm@xmission.com>
Signed-off-by: Hannes Frederic Sowa <hannes@stressinduktion.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

switchdev: bridge: Pass ageing time as clock_t instead of jiffies

The bridge's ageing time is offloaded to hardware when:
1) A port joins a bridge
2) The ageing time of the bridge is changed

In t

switchdev: bridge: Pass ageing time as clock_t instead of jiffies

The bridge's ageing time is offloaded to hardware when:
1) A port joins a bridge
2) The ageing time of the bridge is changed

In the first case the ageing time is offloaded as jiffies, but in the
second case it's offloaded as clock_t, which is what existing switchdev
drivers expect to receive.

Fixes: 6ac311ae8bfb ("Adding switchdev ageing notification on port bridged")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

switchdev: Pass original device to port netdev driver

switchdev drivers need to know the netdev on which the switchdev op was
invoked. For example, the STP state of a VLAN interface configured on to

switchdev: Pass original device to port netdev driver

switchdev drivers need to know the netdev on which the switchdev op was
invoked. For example, the STP state of a VLAN interface configured on top
of a port can change while being member in a bridge. In this case, the
underlying driver should only change the STP state of that particular
VLAN and not of all the VLANs configured on the port.

However, current switchdev infrastructure only passes the port netdev down
to the driver. Solve that by passing the original device down to the
driver as part of the required switchdev object / attribute.

This doesn't entail any change in current switchdev drivers. It simply
enables those supporting stacked devices to know the originating device
and act accordingly.

Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

switchdev: bridge: Check return code is not EOPNOTSUPP

When NET_SWITCHDEV=n, switchdev_port_attr_set simply returns EOPNOTSUPP.
In this case we should not emit errors and warnings to the kernel log.

switchdev: bridge: Check return code is not EOPNOTSUPP

When NET_SWITCHDEV=n, switchdev_port_attr_set simply returns EOPNOTSUPP.
In this case we should not emit errors and warnings to the kernel log.

Reported-by: Sander Eikelenboom <linux@eikelenboom.it>
Tested-by: Christian Borntraeger <borntraeger@de.ibm.com>
Fixes: 0bc05d585d38 ("switchdev: allow caller to explicitly request
attr_set as deferred")
Fixes: 6ac311ae8bfb ("Adding switchdev ageing notification on port
bridged")
Signed-off-by: Ido Schimmel <idosch@mellanox.com>
Signed-off-by: Jiri Pirko <jiri@mellanox.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

Adding switchdev ageing notification on port bridged

Configure ageing time to the HW for newly bridged device

CC: Scott Feldman <sfeldma@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by:

Adding switchdev ageing notification on port bridged

Configure ageing time to the HW for newly bridged device

CC: Scott Feldman <sfeldma@gmail.com>
CC: Jiri Pirko <jiri@resnulli.us>
Signed-off-by: Elad Raz <eladr@mellanox.com>
Acked-by: Jiri Pirko <jiri@mellanox.com>
Acked-by: Scott Feldman <sfeldma@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: stp: when using userspace stp stop kernel hello and hold timers

These should be handled only by the respective STP which is in control.
They become problematic for devices with limited resou

bridge: stp: when using userspace stp stop kernel hello and hold timers

These should be handled only by the respective STP which is in control.
They become problematic for devices with limited resources with many
ports because the hold_timer is per port and fires each second and the
hello timer fires each 2 seconds even though it's global. While in
user-space STP mode these timers are completely unnecessary so it's better
to keep them off.
Also ensure that when the bridge is up these timers are started only when
running with kernel STP.

Signed-off-by: Satish Ashok <sashok@cumulusnetworks.com>
Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: vlan: flush the dynamically learned entries on port vlan delete

Add a new argument to br_fdb_delete_by_port which allows to specify a
vid to match when flushing entries and use it in nbp_vla

bridge: vlan: flush the dynamically learned entries on port vlan delete

Add a new argument to br_fdb_delete_by_port which allows to specify a
vid to match when flushing entries and use it in nbp_vlan_delete() to
flush the dynamically learned entries of the vlan/port pair when removing
a vlan from a port. Before this patch only the local mac was being
removed and the dynamically learned ones were left to expire.
Note that the do_all argument is still respected and if specified, the
vid will be ignored.

Signed-off-by: Nikolay Aleksandrov <nikolay@cumulusnetworks.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: fix br_stp_set_bridge_priority race conditions

After the ->set() spinlocks were removed br_stp_set_bridge_priority
was left running without any protection when used via sysfs. It can
race wi

bridge: fix br_stp_set_bridge_priority race conditions

After the ->set() spinlocks were removed br_stp_set_bridge_priority
was left running without any protection when used via sysfs. It can
race with port add/del and could result in use-after-free cases and
corrupted lists. Tested by running port add/del in a loop with stp
enabled while setting priority in a loop, crashes are easily
reproducible.
The spinlocks around sysfs ->set() were removed in commit:
14f98f258f19 ("bridge: range check STP parameters")
There's also a race condition in the netlink priority support that is
fixed by this change, but it was introduced recently and the fixes tag
covers it, just in case it's needed the commit is:
af615762e972 ("bridge: add ageing_time, stp_state, priority over netlink")

Signed-off-by: Nikolay Aleksandrov <razor@blackwall.org>
Fixes: 14f98f258f19 ("bridge: range check STP parameters")
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...