rtnetlink: bridge: mcast: Relax group address validation in common code

In the upcoming VXLAN MDB implementation, the 0.0.0.0 and :: MDB entries
will act as catchall entries for unregistered IP mult

rtnetlink: bridge: mcast: Relax group address validation in common code

In the upcoming VXLAN MDB implementation, the 0.0.0.0 and :: MDB entries
will act as catchall entries for unregistered IP multicast traffic in a
similar fashion to the 00:00:00:00:00:00 VXLAN FDB entry that is used to
transmit BUM traffic.

In deployments where inter-subnet multicast forwarding is used, not all
the VTEPs in a tenant domain are members in all the broadcast domains.
It is therefore advantageous to transmit BULL (broadcast, unknown
unicast and link-local multicast) and unregistered IP multicast traffic
on different tunnels. If the same tunnel was used, a VTEP only
interested in IP multicast traffic would also pull all the BULL traffic
and drop it as it is not a member in the originating broadcast domain
[1].

Prepare for this change by allowing the 0.0.0.0 group address in the
common rtnetlink MDB code and forbid it in the bridge driver. A similar
change is not needed for IPv6 because the common code only validates
that the group address is not the all-nodes address.

[1] https://datatracker.ietf.org/doc/html/draft-ietf-bess-evpn-irb-mcast#section-2.6

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

rtnetlink: bridge: mcast: Move MDB handlers out of bridge driver

Currently, the bridge driver registers handlers for MDB netlink
messages, making it impossible for other drivers to implement MDB
sup

rtnetlink: bridge: mcast: Move MDB handlers out of bridge driver

Currently, the bridge driver registers handlers for MDB netlink
messages, making it impossible for other drivers to implement MDB
support.

As a preparation for VXLAN MDB support, move the MDB handlers out of the
bridge driver to the core rtnetlink code. The rtnetlink code will call
into individual drivers by invoking their previously added MDB net
device operations.

Note that while the diffstat is large, the change is mechanical. It
moves code out of the bridge driver to rtnetlink code. Also note that a
similar change was made in 2012 with commit 77162022ab26 ("net: add
generic PF_BRIDGE:RTM_ FDB hooks") that moved FDB handlers out of the
bridge driver to the core rtnetlink code.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: mcast: Implement MDB net device operations

Implement the previously added MDB net device operations in the bridge
driver so that they could be invoked by core rtnetlink code in the next
patc

bridge: mcast: Implement MDB net device operations

Implement the previously added MDB net device operations in the bridge
driver so that they could be invoked by core rtnetlink code in the next
patch.

The operations are identical to the existing br_mdb_{dump,add,del}
functions. The '_new' suffix will be removed in the next patch. The
functions are re-implemented in this patch to make the conversion in the
next patch easier to review.

Add dummy implementations when 'CONFIG_BRIDGE_IGMP_SNOOPING' is
disabled, so that an error will be returned to user space when it is
trying to add or delete an MDB entry. This is consistent with existing
behavior where the bridge driver does not even register rtnetlink
handlers for RTM_{NEW,DEL,GET}MDB messages when this Kconfig option is
disabled.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Reviewed-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: mcast: Move validation to a policy

Future patches are going to move parts of the bridge MDB code to the
common rtnetlink code in preparation for VXLAN MDB support. To
facilitate code sharing

bridge: mcast: Move validation to a policy

Future patches are going to move parts of the bridge MDB code to the
common rtnetlink code in preparation for VXLAN MDB support. To
facilitate code sharing between both drivers, move the validation of the
top level attributes in RTM_{NEW,DEL}MDB messages to a policy that will
eventually be moved to the rtnetlink code.

Use 'NLA_NESTED' for 'MDBA_SET_ENTRY_ATTRS' instead of
NLA_POLICY_NESTED() as this attribute is going to be validated using
different policies in the underlying drivers.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Remove pointless sequence generation counter assignment

The purpose of the sequence generation counter in the netlink callback
is to identify if a multipart dump is consistent or not

bridge: mcast: Remove pointless sequence generation counter assignment

The purpose of the sequence generation counter in the netlink callback
is to identify if a multipart dump is consistent or not by calling
nl_dump_check_consistent() whenever a message is generated.

The function is not invoked by the MDB code, rendering the sequence
generation counter assignment pointless. Remove it.

Note that even if the function was invoked, we still could not
accurately determine if the dump is consistent or not, as there is no
sequence generation counter for MDB entries, unlike nexthop objects, for
example.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Use correct define in MDB dump

'MDB_PG_FLAGS_PERMANENT' and 'MDB_PERMANENT' happen to have the same
value, but the latter is uAPI and cannot change, so use it when dumping
an MDB entr

bridge: mcast: Use correct define in MDB dump

'MDB_PG_FLAGS_PERMANENT' and 'MDB_PERMANENT' happen to have the same
value, but the latter is uAPI and cannot change, so use it when dumping
an MDB entry.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: bridge: Add br_multicast_del_port_group()

Since cleaning up the effects of br_multicast_new_port_group() just
consists of delisting and freeing the memory, the function
br_mdb_add_group_star_g(

net: bridge: Add br_multicast_del_port_group()

Since cleaning up the effects of br_multicast_new_port_group() just
consists of delisting and freeing the memory, the function
br_mdb_add_group_star_g() inlines the corresponding code. In the following
patches, number of per-port and per-port-VLAN MDB entries is going to be
maintained, and that counter will have to be updated. Because that logic
is going to be hidden in the br_multicast module, introduce a new hook
intended to again remove a newly-created group.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: Move extack-setting to br_multicast_new_port_group()

Now that br_multicast_new_port_group() takes an extack argument, move
setting the extack there. The downside is that the error messa

net: bridge: Move extack-setting to br_multicast_new_port_group()

Now that br_multicast_new_port_group() takes an extack argument, move
setting the extack there. The downside is that the error messages end
up being less specific (the function cannot distinguish between (S,G)
and (*,G) groups). However, the alternative is to check in the caller
whether the callee set the extack, and if it didn't, set it. But that
is only done when the callee is not exactly known. (E.g. in case of a
notifier invocation.)

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: bridge: Add extack to br_multicast_new_port_group()

Make it possible to set an extack in br_multicast_new_port_group().
Eventually, this function will check for per-port and per-port-vlan
MDB m

net: bridge: Add extack to br_multicast_new_port_group()

Make it possible to set an extack in br_multicast_new_port_group().
Eventually, this function will check for per-port and per-port-vlan
MDB maximums, and will use the extack to communicate the reason for
the bounce.

Signed-off-by: Petr Machata <petrm@nvidia.com>
Reviewed-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

bridge: mcast: Support replacement of MDB port group entries

Now that user space can specify additional attributes of port group
entries such as filter mode and source list, it makes sense to allow

bridge: mcast: Support replacement of MDB port group entries

Now that user space can specify additional attributes of port group
entries such as filter mode and source list, it makes sense to allow
user space to atomically modify these attributes by replacing entries
instead of forcing user space to delete the entries and add them back.

Replace MDB port group entries when the 'NLM_F_REPLACE' flag is
specified in the netlink message header.

When a (*, G) entry is replaced, update the following attributes: Source
list, state, filter mode, protocol and flags. If the entry is temporary
and in EXCLUDE mode, reset the group timer to the group membership
interval. If the entry is temporary and in INCLUDE mode, reset the
source timers of associated sources to the group membership interval.

Examples:

# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.2 filter_mode include
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.2 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto static 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode include source_list 192.0.2.2/0.00,192.0.2.1/0.00 proto static 0.00

# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 permanent source_list 192.0.2.1,192.0.2.3 filter_mode exclude proto zebra
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra blocked 0.00
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude source_list 192.0.2.3/0.00,192.0.2.1/0.00 proto zebra 0.00

# bridge mdb replace dev br0 port dummy10 grp 239.1.1.1 temp source_list 192.0.2.4,192.0.2.3 filter_mode include proto bgp
# bridge -d -s mdb show
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.4 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.3 temp filter_mode include proto bgp 0.00
dev br0 port dummy10 grp 239.1.1.1 temp filter_mode include source_list 192.0.2.4/259.44,192.0.2.3/259.44 proto bgp 0.00

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Allow user space to specify MDB entry routing protocol

Add the 'MDBE_ATTR_RTPORT' attribute to allow user space to specify the
routing protocol of the MDB port group entry. Enforce a

bridge: mcast: Allow user space to specify MDB entry routing protocol

Add the 'MDBE_ATTR_RTPORT' attribute to allow user space to specify the
routing protocol of the MDB port group entry. Enforce a minimum value of
'RTPROT_STATIC' to prevent user space from using protocol values that
should only be set by the kernel (e.g., 'RTPROT_KERNEL'). Maintain
backward compatibility by defaulting to 'RTPROT_STATIC'.

The protocol is already visible to user space in RTM_NEWMDB responses
and notifications via the 'MDBA_MDB_EATTR_RTPROT' attribute.

The routing protocol allows a routing daemon to distinguish between
entries configured by it and those configured by the administrator. Once
MDB flush is supported, the protocol can be used as a criterion
according to which the flush is performed.

Examples:

# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto kernel
Error: integer out of range.

# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 permanent proto static

# bridge mdb add dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent proto zebra

# bridge mdb add dev br0 port dummy10 grp 239.1.1.2 permanent source_list 198.51.100.1,198.51.100.2 filter_mode include proto 250

# bridge -d mdb show
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.2 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 src 198.51.100.1 permanent filter_mode include proto 250
dev br0 port dummy10 grp 239.1.1.2 permanent filter_mode include source_list 198.51.100.2/0.00,198.51.100.1/0.00 proto 250
dev br0 port dummy10 grp 239.1.1.1 src 192.0.2.1 permanent filter_mode include proto zebra
dev br0 port dummy10 grp 239.1.1.1 permanent filter_mode exclude proto static

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Allow user space to add (*, G) with a source list and filter mode

Add new netlink attributes to the RTM_NEWMDB request that allow user
space to add (*, G) with a source list and filte

bridge: mcast: Allow user space to add (*, G) with a source list and filter mode

Add new netlink attributes to the RTM_NEWMDB request that allow user
space to add (*, G) with a source list and filter mode.

The RTM_NEWMDB message can already dump such entries (created by the
kernel) so there is no need to add dump support. However, the message
contains a different set of attributes depending if it is a request or a
response. The naming and structure of the new attributes try to follow
the existing ones used in the response.

Request:

[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_SET_ENTRY ]
struct br_mdb_entry
[ MDBA_SET_ENTRY_ATTRS ]
[ MDBE_ATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBE_ATTR_SRC_LIST ] // new
[ MDBE_SRC_LIST_ENTRY ]
[ MDBE_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ ...]
[ MDBE_ATTR_GROUP_MODE ] // new
u8

Response:

[ struct nlmsghdr ]
[ struct br_port_msg ]
[ MDBA_MDB ]
[ MDBA_MDB_ENTRY ]
[ MDBA_MDB_ENTRY_INFO ]
struct br_mdb_entry
[ MDBA_MDB_EATTR_TIMER ]
u32
[ MDBA_MDB_EATTR_SOURCE ]
struct in_addr / struct in6_addr
[ MDBA_MDB_EATTR_RTPROT ]
u8
[ MDBA_MDB_EATTR_SRC_LIST ]
[ MDBA_MDB_SRCLIST_ENTRY ]
[ MDBA_MDB_SRCATTR_ADDRESS ]
struct in_addr / struct in6_addr
[ MDBA_MDB_SRCATTR_TIMER ]
u8
[...]
[ MDBA_MDB_EATTR_GROUP_MODE ]
u8

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Add support for (*, G) with a source list and filter mode

In preparation for allowing user space to add (*, G) entries with a
source list and associated filter mode, add the necessary

bridge: mcast: Add support for (*, G) with a source list and filter mode

In preparation for allowing user space to add (*, G) entries with a
source list and associated filter mode, add the necessary plumbing to
handle such requests.

Extend the MDB configuration structure with a currently empty source
array and filter mode that is currently hard coded to EXCLUDE.

Add the source entries and the corresponding (S, G) entries before
making the new (*, G) port group entry visible to the data path.

Handle the creation of each source entry in a similar fashion to how it
is created from the data path in response to received Membership
Reports: Create the source entry, arm the source timer (if needed), add
a corresponding (S, G) forwarding entry and finally mark the source
entry as installed (by user space).

Add the (S, G) entry by populating an MDB configuration structure and
calling br_mdb_add_group_sg() as if a new entry is created by user
space, with the sole difference that the 'src_entry' field is set to
make sure that the group timer of such entries is never armed.

Note that it is not currently possible to add more than 32 source
entries to a port group entry. If this proves to be a problem we can
either increase 'PG_SRC_ENT_LIMIT' or avoid forcing a limit on entries
created by user space.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source

User space will soon be able to install a (*, G) with a source list,
prompting the creation of a (S, G) entry for each sou

bridge: mcast: Avoid arming group timer when (S, G) corresponds to a source

User space will soon be able to install a (*, G) with a source list,
prompting the creation of a (S, G) entry for each source.

In this case, the group timer of the (S, G) entry should never be set.

Solve this by adding a new field to the MDB configuration structure that
denotes whether the (S, G) corresponds to a source or not.

The field will be set in a subsequent patch where br_mdb_add_group_sg()
is called in order to create a (S, G) entry for each user provided
source.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Add a centralized error path

Subsequent patches will add memory allocations in br_mdb_config_init()
as the MDB configuration structure will include a linked list of source
entries. Th

bridge: mcast: Add a centralized error path

Subsequent patches will add memory allocations in br_mdb_config_init()
as the MDB configuration structure will include a linked list of source
entries. This memory will need to be freed regardless if br_mdb_add()
succeeded or failed.

As a preparation for this change, add a centralized error path where the
memory will be freed.

Note that br_mdb_del() already has one error path and therefore does not
require any changes.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Place netlink policy before validation functions

Subsequent patches are going to add additional validation functions and
netlink policies. Some of these functions will need to perform

bridge: mcast: Place netlink policy before validation functions

Subsequent patches are going to add additional validation functions and
netlink policies. Some of these functions will need to perform parsing
using nla_parse_nested() and the new policies.

In order to keep all the policies next to each other, move the current
policy to before the validation functions.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Split (*, G) and (S, G) addition into different functions

When the bridge is using IGMP version 3 or MLD version 2, it handles the
addition of (*, G) and (S, G) entries differently.

bridge: mcast: Split (*, G) and (S, G) addition into different functions

When the bridge is using IGMP version 3 or MLD version 2, it handles the
addition of (*, G) and (S, G) entries differently.

When a new (S, G) port group entry is added, all the (*, G) EXCLUDE
ports need to be added to the port group of the new entry. Similarly,
when a new (*, G) EXCLUDE port group entry is added, the port needs to
be added to the port group of all the matching (S, G) entries.

Subsequent patches will create more differences between both entry
types. Namely, filter mode and source list can only be specified for (*,
G) entries.

Given the current and future differences between both entry types,
handle the addition of each entry type in a different function, thereby
avoiding the creation of one complex function.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Do not derive entry type from its filter mode

Currently, the filter mode (i.e., INCLUDE / EXCLUDE) of MDB entries
cannot be set from user space. Instead, it is set by the kernel
accor

bridge: mcast: Do not derive entry type from its filter mode

Currently, the filter mode (i.e., INCLUDE / EXCLUDE) of MDB entries
cannot be set from user space. Instead, it is set by the kernel
according to the entry type: (*, G) entries are treated as EXCLUDE and
(S, G) entries are treated as INCLUDE. This allows the kernel to derive
the entry type from its filter mode.

Subsequent patches will allow user space to set the filter mode of (*,
G) entries, making the current assumption incorrect.

As a preparation, remove the current assumption and instead determine
the entry type from its key, which is a more direct way.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Remove redundant function arguments

Drop the first three arguments and instead extract them from the MDB
configuration structure.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acke

bridge: mcast: Remove redundant function arguments

Drop the first three arguments and instead extract them from the MDB
configuration structure.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Move checks out of critical section

The checks only require information parsed from the RTM_NEWMDB netlink
message and do not rely on any state stored in the bridge driver.
Therefore,

bridge: mcast: Move checks out of critical section

The checks only require information parsed from the RTM_NEWMDB netlink
message and do not rely on any state stored in the bridge driver.
Therefore, there is no need to perform the checks in the critical
section under the multicast lock.

Move the checks out of the critical section.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Remove br_mdb_parse()

The parsing of the netlink messages and the validity checks are now
performed in br_mdb_config_init() so we can remove br_mdb_parse().

This finally allows us to

bridge: mcast: Remove br_mdb_parse()

The parsing of the netlink messages and the validity checks are now
performed in br_mdb_config_init() so we can remove br_mdb_parse().

This finally allows us to stop passing netlink attributes deep in the
MDB control path and only use the MDB configuration structure.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Use MDB group key from configuration structure

The MDB group key (i.e., {source, destination, protocol, VID}) is
currently determined under the multicast lock from the netlink
attribu

bridge: mcast: Use MDB group key from configuration structure

The MDB group key (i.e., {source, destination, protocol, VID}) is
currently determined under the multicast lock from the netlink
attributes. Instead, use the group key from the MDB configuration
structure that was prepared before acquiring the lock.

No functional changes intended.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Propagate MDB configuration structure further

As an intermediate step towards only using the new MDB configuration
structure, pass it further in the control path instead of passing
in

bridge: mcast: Propagate MDB configuration structure further

As an intermediate step towards only using the new MDB configuration
structure, pass it further in the control path instead of passing
individual attributes.

No functional changes intended.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Use MDB configuration structure where possible

The MDB configuration structure (i.e., struct br_mdb_config) now
includes all the necessary information from the parsed RTM_{NEW,DEL}MDB

bridge: mcast: Use MDB configuration structure where possible

The MDB configuration structure (i.e., struct br_mdb_config) now
includes all the necessary information from the parsed RTM_{NEW,DEL}MDB
netlink messages, so use it.

This will later allow us to delete the calls to br_mdb_parse() from
br_mdb_add() and br_mdb_del().

No functional changes intended.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

bridge: mcast: Remove redundant checks

These checks are now redundant as they are performed by
br_mdb_config_init() while parsing the RTM_{NEW,DEL}MDB messages.

Remove them.

Signed-off-by: Ido Sch

bridge: mcast: Remove redundant checks

These checks are now redundant as they are performed by
br_mdb_config_init() while parsing the RTM_{NEW,DEL}MDB messages.

Remove them.

Signed-off-by: Ido Schimmel <idosch@nvidia.com>
Acked-by: Nikolay Aleksandrov <razor@blackwall.org>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...