Revert "8250: add support for ASIX devices with a FIFO bug"

This reverts commit eb26dfe8aa7eeb5a5aa0b7574550125f8aa4c3b3.

Commit eb26dfe8aa7e ("8250: add support for ASIX devices with a FIFO
bug")

Revert "8250: add support for ASIX devices with a FIFO bug"

This reverts commit eb26dfe8aa7eeb5a5aa0b7574550125f8aa4c3b3.

Commit eb26dfe8aa7e ("8250: add support for ASIX devices with a FIFO
bug") merged on Jul 13, 2012 adds a quirk for PCI_VENDOR_ID_ASIX
(0x9710). But that ID is the same as PCI_VENDOR_ID_NETMOS defined in
1f8b061050c7 ("[PATCH] Netmos parallel/serial/combo support") merged
on Mar 28, 2005. In pci_serial_quirks array, the NetMos entry always
takes precedence over the ASIX entry even since it was initially
merged, code in that commit is always unreachable.

In my tests, adding the FIFO workaround to pci_netmos_init() makes no
difference, and the vendor driver also does not have such workaround.
Given that the code was never used for over a decade, it's safe to
revert it.

Also, the real PCI_VENDOR_ID_ASIX should be 0x125b, which is used on
their newer AX99100 PCIe serial controllers released on 2016. The FIFO
workaround should not be intended for these newer controllers, and it
was never implemented in vendor driver.

Fixes: eb26dfe8aa7e ("8250: add support for ASIX devices with a FIFO bug")
Cc: stable <stable@kernel.org>
Signed-off-by: Jiaqing Zhao <jiaqing.zhao@linux.intel.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20230619155743.827859-1-jiaqing.zhao@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: RT288x/Au1xxx code away from core

A non-trivial amount of RT288x/Au1xxx code is encapsulated into
ifdeffery in 8250_port / 8250_early and some if UPIO_AU blocks.
Create a separate file

serial: 8250: RT288x/Au1xxx code away from core

A non-trivial amount of RT288x/Au1xxx code is encapsulated into
ifdeffery in 8250_port / 8250_early and some if UPIO_AU blocks.
Create a separate file from them.

Also handle errors properly in the cases where RT288x/Au1xxx code is
not configured.

It seems that 0x1000 mapsize is likely overkill but I've kept it the
same as previously (the value was shrunk to that value in commit
b2b13cdfd05e ("SERIAL 8250: Fixes for Alchemy UARTs.")). Seemingly, the
driver only needs to access register at 0x28 for the divisor latch.

The Kconfig side is a bit tricky. As SERIAL_8250_RT288X is bool it can
only be =y. It is possible to have SERIAL_8250=m + SERIAL_8250_RT288X=y
which required altering when 8250/ is included or the rt288x would not
be built.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-5-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Add dl_read/write, bugs and mapsize into plat_serial8250_port

Add mapsize, bugs, and divisor latch read/write functions
(->dl_read/write()) into plat_serial8250_port to carry the setup

serial: 8250: Add dl_read/write, bugs and mapsize into plat_serial8250_port

Add mapsize, bugs, and divisor latch read/write functions
(->dl_read/write()) into plat_serial8250_port to carry the setup
necessary for RT288x/Au1xxx devices over to uart port.

Document the added members with kerneldoc style but do not enable
kerneldoc yet as there are many fields which remain undocumented.

While at it, convert .bugs in struct uart_8250_port to u16 to match it
with the type used in struct plat_serial8250_port.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Document uart_8250_port's ->dl_read/write()

Add documentation for the struct uart_8250_port divisor latch function
pointers. Documentation is in kernel doc format but don't enable kern

serial: 8250: Document uart_8250_port's ->dl_read/write()

Add documentation for the struct uart_8250_port divisor latch function
pointers. Documentation is in kernel doc format but don't enable kernel
doc yet as many other fields remain undocumented.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Change dl_read/write to handle value as u32

Divisor latch read/write functions currently handle the value is int.
As the value is related to HW context, u32 makes much more sense than

serial: 8250: Change dl_read/write to handle value as u32

Divisor latch read/write functions currently handle the value is int.
As the value is related to HW context, u32 makes much more sense than a
signed type.

While at it, name the parameters in the callback signature.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230511121029.13128-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: Remove extern from func prototypes in headers

Remove unnecessary externs from function prototypes in serial_8250.h
and serial_core.h.

Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-

serial: Remove extern from func prototypes in headers

Remove unnecessary externs from function prototypes in serial_8250.h
and serial_core.h.

Suggested-by: Jiri Slaby <jirislaby@kernel.org>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20230309080923.11778-4-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Reorder fields in 'struct plat_serial8250_port'

Group some variables based on their sizes to reduce hole and avoid padding.
On x86_64, this shrinks the size of 'struct plat_serial8250_

serial: 8250: Reorder fields in 'struct plat_serial8250_port'

Group some variables based on their sizes to reduce hole and avoid padding.
On x86_64, this shrinks the size of 'struct plat_serial8250_port'
from 144 to 128 bytes.

It saves a few bytes of memory.

Signed-off-by: Christophe JAILLET <christophe.jaillet@wanadoo.fr>
Link: https://lore.kernel.org/r/f3cb1efe1454e0615840fd331ee335bc441589a9.1676665358.git.christophe.jaillet@wanadoo.fr
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Toggle IER bits on only after irq has been set up

Invoking TIOCVHANGUP on 8250_mid port on Ice Lake-D and then reopening
the port triggers these faults during serial8250_do_startup():

serial: 8250: Toggle IER bits on only after irq has been set up

Invoking TIOCVHANGUP on 8250_mid port on Ice Lake-D and then reopening
the port triggers these faults during serial8250_do_startup():

DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write NO_PASID] Request device [00:1a.0] fault addr 0x0 [fault reason 0x05] PTE Write access is not set

If the IRQ hasn't been set up yet, the UART will have zeroes in its MSI
address/data registers. Disabling the IRQ at the interrupt controller
won't stop the UART from performing a DMA write to the address programmed
in its MSI address register (zero) when it wants to signal an interrupt.

The UARTs (in Ice Lake-D) implement PCI 2.1 style MSI without masking
capability, so there is no way to mask the interrupt at the source PCI
function level, except disabling the MSI capability entirely, but that
would cause it to fall back to INTx# assertion, and the PCI specification
prohibits disabling the MSI capability as a way to mask a function's
interrupt service request.

The MSI address register is zeroed by the hangup as the irq is freed.
The interrupt is signalled during serial8250_do_startup() performing a
THRE test that temporarily toggles THRI in IER. The THRE test currently
occurs before UART's irq (and MSI address) is properly set up.

Refactor serial8250_do_startup() such that irq is set up before the
THRE test. The current irq setup code is intermixed with the timer
setup code. As THRE test must be performed prior to the timer setup,
extract it into own function and call it only after the THRE test.

The ->setup_timer() needs to be part of the struct uart_8250_ops in
order to not create circular dependency between 8250 and 8250_base
modules.

Fixes: 40b36daad0ac ("[PATCH] 8250 UART backup timer")
Reported-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Lennert Buytenhek <buytenh@arista.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922070005.2965-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: Make ->set_termios() old ktermios const

There should be no reason to adjust old ktermios which is going to get
discarded anyway.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Sig

serial: Make ->set_termios() old ktermios const

There should be no reason to adjust old ktermios which is going to get
discarded anyway.

Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220816115739.10928-7-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: create lsr_save_mask

Allow drivers to alter LSR save mask.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com

serial: 8250: create lsr_save_mask

Allow drivers to alter LSR save mask.

Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-3-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: make saved LSR larger

DW flags address received as BIT(8) in LSR. In order to not lose that
on read, enlarge lsr_saved_flags to u16.

Adjust lsr/status variables and related call chain

serial: 8250: make saved LSR larger

DW flags address received as BIT(8) in LSR. In order to not lose that
on read, enlarge lsr_saved_flags to u16.

Adjust lsr/status variables and related call chains to use u16.
Technically, some of these type conversion would not be needed but it
doesn't hurt to be consistent.

Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220624204210.11112-2-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

Revert "serial: 8250: Handle UART without interrupt on TEMT using em485"

This partially reverts commit f6f586102add. The code added by
that commit containted math overflow for 32-bit archs. In
addit

Revert "serial: 8250: Handle UART without interrupt on TEMT using em485"

This partially reverts commit f6f586102add. The code added by
that commit containted math overflow for 32-bit archs. In
addition, the approach used in it is unnecessarily complicated
requiring a dedicated timer just for notemt. A simpler approach
for providing UART_CAP_NOTEMT already exists (patches 1-2):
https://lore.kernel.org/linux-serial/20220411083321.9131-3-ilpo.jarvinen@linux.intel.com/T/#u
Thus, simply revert the UART_CAP_NOTEMT change for now.

There were two driver changes within the patch series adding
UART_CAP_NOTEMT taking advantage of the newly added flag.
This does not revert the driver changes and therefore also
UART_CAP_NOTEMT define has to remain. UART_CAP_NOTEMT remains
no-op until support is again added.

Fixes: f6f586102add ("serial: 8250: Handle UART without interrupt on TEMT using em485")
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/5f874142-fb1f-bff7-f33-fac823e65e2e@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Handle UART without interrupt on TEMT using em485

Introduce the UART_CAP_NOTEMT capability. The capability indicates that
the UART doesn't have an interrupt available on TEMT.

In the

serial: 8250: Handle UART without interrupt on TEMT using em485

Introduce the UART_CAP_NOTEMT capability. The capability indicates that
the UART doesn't have an interrupt available on TEMT.

In the case where the device does not support it, we calculate the
maximum time it could take for the transmitter to empty the
shift register. When we get in the situation where we get the
THRE interrupt, we check if the TEMT bit is set. If it's not, we start
the a timer and recall __stop_tx() after the delay.

The transmit sequence is a bit modified when the capability is set. The
new timer is used between the last interrupt(THRE) and a potential
stop_tx timer.

Signed-off-by: Giulio Benetti <giulio.benetti@micronovasrl.com>
[moved to use added UART_CAP_TEMT]
Signed-off-by: Heiko Stuebner <heiko.stuebner@theobroma-systems.com>
[moved to use added UART_CAP_NOTEMT, improve timeout]
Signed-off-by: Eric Tremblay <etremblay@distech-controls.com>
[rebased to v5.17, making use of tty_get_frame_size]
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20220330104642.229507-2-u.kleine-koenig@pengutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Move Alpha-specific quirk out of the core

struct uart_8250_port contains mcr_mask and mcr_force members whose
sole purpose is to work around an Alpha-specific quirk. This code
doesn't

serial: 8250: Move Alpha-specific quirk out of the core

struct uart_8250_port contains mcr_mask and mcr_force members whose
sole purpose is to work around an Alpha-specific quirk. This code
doesn't belong in the core where it is executed by everyone else,
so move it to a proper ->set_mctrl callback which is used on the
affected Alpha machine only.

The quirk was introduced in January 1995:
https://git.kernel.org/pub/scm/linux/kernel/git/history/history.git/diff/drivers/char/serial.c?h=1.1.83

The members in struct uart_8250_port were added in 2002:
https://git.kernel.org/history/history/c/4524aad27854

The quirk applies to non-PCI Alphas and arch/alpha/Kconfig specifies
"select FORCE_PCI if !ALPHA_JENSEN". So apparently the only affected
machine is the EISA-based Jensen that Linus was working on back then:
https://lore.kernel.org/all/CAHk-=wj1JWZ3sCrGz16nxEj7=0O+srMg6Ah3iPTDXSPKEws_SA@mail.gmail.com/

Up until now the quirk is not applied unless CONFIG_PCI is disabled.
If users forget to do that or run a generic Alpha kernel, the serial
ports aren't usable on Jensen. Avoid by confining the quirk to
CONFIG_ALPHA_JENSEN instead of !CONFIG_PCI. On generic Alpha kernels,
auto-detect at runtime whether the quirk needs to be applied.

Cc: Russell King <rmk+kernel@armlinux.org.uk>
Cc: Ulrich Teichert <krypton@ulrich-teichert.org>
Cc: Linus Torvalds <torvalds@linux-foundation.org>
Signed-off-by: Lukas Wunner <lukas@wunner.de>
Link: https://lore.kernel.org/r/b83d069cb516549b8a5420e097bb6bdd806f36fc.1640695609.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Toggle IER bits on only after irq has been set up

[ Upstream commit 039d4926379b1d1c17b51cf21c500a5eed86899e ]

Invoking TIOCVHANGUP on 8250_mid port on Ice Lake-D and then reopening
t

serial: 8250: Toggle IER bits on only after irq has been set up

[ Upstream commit 039d4926379b1d1c17b51cf21c500a5eed86899e ]

Invoking TIOCVHANGUP on 8250_mid port on Ice Lake-D and then reopening
the port triggers these faults during serial8250_do_startup():

DMAR: DRHD: handling fault status reg 3
DMAR: [DMA Write NO_PASID] Request device [00:1a.0] fault addr 0x0 [fault reason 0x05] PTE Write access is not set

If the IRQ hasn't been set up yet, the UART will have zeroes in its MSI
address/data registers. Disabling the IRQ at the interrupt controller
won't stop the UART from performing a DMA write to the address programmed
in its MSI address register (zero) when it wants to signal an interrupt.

The UARTs (in Ice Lake-D) implement PCI 2.1 style MSI without masking
capability, so there is no way to mask the interrupt at the source PCI
function level, except disabling the MSI capability entirely, but that
would cause it to fall back to INTx# assertion, and the PCI specification
prohibits disabling the MSI capability as a way to mask a function's
interrupt service request.

The MSI address register is zeroed by the hangup as the irq is freed.
The interrupt is signalled during serial8250_do_startup() performing a
THRE test that temporarily toggles THRI in IER. The THRE test currently
occurs before UART's irq (and MSI address) is properly set up.

Refactor serial8250_do_startup() such that irq is set up before the
THRE test. The current irq setup code is intermixed with the timer
setup code. As THRE test must be performed prior to the timer setup,
extract it into own function and call it only after the THRE test.

The ->setup_timer() needs to be part of the struct uart_8250_ops in
order to not create circular dependency between 8250 and 8250_base
modules.

Fixes: 40b36daad0ac ("[PATCH] 8250 UART backup timer")
Reported-by: Lennert Buytenhek <buytenh@arista.com>
Tested-by: Lennert Buytenhek <buytenh@arista.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Ilpo Järvinen <ilpo.jarvinen@linux.intel.com>
Link: https://lore.kernel.org/r/20220922070005.2965-1-ilpo.jarvinen@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

tty/serial: make port of serial8250_register_8250_port const

After the previous patch, we can make port passed to
serial8250_find_match_or_unused const. And then we can make const also
port of seria

tty/serial: make port of serial8250_register_8250_port const

After the previous patch, we can make port passed to
serial8250_find_match_or_unused const. And then we can make const also
port of serial8250_register_8250_port.

Signed-off-by: Jiri Slaby <jslaby@suse.cz>
Link: https://lore.kernel.org/r/20210519072153.3859-2-jslaby@suse.cz
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

tty: serial: 8250: 8250_port: Move prototypes to shared location

Fixes the following W=1 kernel build warning(s):

drivers/tty/serial/8250/8250_port.c:349:14: warning: no previous prototype for ‘au

tty: serial: 8250: 8250_port: Move prototypes to shared location

Fixes the following W=1 kernel build warning(s):

drivers/tty/serial/8250/8250_port.c:349:14: warning: no previous prototype for ‘au_serial_in’ [-Wmissing-prototypes]
drivers/tty/serial/8250/8250_port.c:359:6: warning: no previous prototype for ‘au_serial_out’ [-Wmissing-prototypes]

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Jiri Slaby <jirislaby@kernel.org>
Cc: Mike Hudson <Exoray@isys.ca>
Cc: linux-serial@vger.kernel.org
Signed-off-by: Lee Jones <lee.jones@linaro.org>
Link: https://lore.kernel.org/r/20201112105857.2078977-3-lee.jones@linaro.org
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Add 8250 port clock update method

Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happ

serial: 8250: Add 8250 port clock update method

Some platforms can be designed in a way so the UART port reference clock
might be asynchronously changed at some point. In Baikal-T1 SoC this may
happen due to the reference clock being shared between two UART ports, on
the Allwinner SoC the reference clock is derived from the CPU clock, so
any CPU frequency change should get to be known/reflected by/in the UART
controller as well. But it's not enough to just update the
uart_port->uartclk field of the corresponding UART port, the 8250
controller reference clock divisor should be altered so to preserve
current baud rate setting. All of these things is done in a coherent
way by calling the serial8250_update_uartclk() method provided in this
patch. Though note that it isn't supposed to be called from within the
UART port callbacks because the locks using to the protect the UART port
data are already taken in there.

Signed-off-by: Serge Semin <Sergey.Semin@baikalelectronics.ru>

Link: https://lore.kernel.org/r/20200723003357.26897-2-Sergey.Semin@baikalelectronics.ru
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250_port: Don't use power management for kernel console

Doing any kind of power management for kernel console is really bad idea.

First of all, it runs in poll and atomic mode. This fact a

serial: 8250_port: Don't use power management for kernel console

Doing any kind of power management for kernel console is really bad idea.

First of all, it runs in poll and atomic mode. This fact attaches a limitation
on the functions that might be called. For example, pm_runtime_get_sync() might
sleep and thus can't be used. This call needs, for example, to bring the device
to powered on state on the system, where the power on sequence may require
on-atomic operations, such as Intel Cherrytrail with ACPI enumerated UARTs.
That said, on ACPI enabled platforms it might even call firmware for a job.

On the other hand pm_runtime_get() doesn't guarantee that device will become
powered on fast enough.

Besides that, imagine the case when console is about to print a kernel Oops and
it's powered off. In such an emergency case calling the complex functions is
not the best what we can do, taking into consideration that user wants to see
at least something of the last kernel word before it passes away.

Here we modify the 8250 console code to prevent runtime power management.

Note, there is a behaviour change for OMAP boards. It will require to detach
kernel console to become idle.

Link: https://lists.openwall.net/linux-kernel/2018/09/29/65
Suggested-by: Russell King <rmk+kernel@armlinux.org.uk>
Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20200217114016.49856-6-andriy.shevchenko@linux.intel.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Generalize rs485 software emulation

Commit e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
So far t

serial: 8250: Generalize rs485 software emulation

Commit e490c9144cfa ("tty: Add software emulated RS485 support for 8250")
introduced support to use RTS as an rs485 Transmit Enable signal.
So far the only drivers taking advantage of it are 8250_omap.c and
8250_of.c.

We're about to make use of the feature in 8250_bcm2835aux.c as well.
The bcm2835aux differs from omap chips by inverting the meaning of RTS
in the MCR register. Moreover, omap achieves half-duplex mode by
disabling the RX interrupt and clearing the RX FIFO when TX stops.
The bcm2835aux requires disabling the receiver instead.

Support these behavioral differences by generalizing the rs485 emulation:
Introduce ->rs485_start_tx() and ->rs485_stop_tx() callbacks in struct
uart_8250_port, provide generic implementations containing the existing
code and use them as callbacks in 8250_omap.c and 8250_of.c.

start_tx_rs485() is idempotent in that it recognizes whether RTS is
already asserted. Achieve the same by introducing a tx_stopped flag in
struct uart_8250_em485. This may even perform a little better on arches
where memory access is faster than mmio access.

Signed-off-by: Lukas Wunner <lukas@wunner.de>
Cc: Matwey V. Kornilov <matwey@sai.msu.ru>
Link: https://lore.kernel.org/r/5ac0464ae4414708e723a1e0d52b0c1b2bd41b9b.1582895077.git.lukas@wunner.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

tty/serial: Migrate 8250_fsl to use has_sysrq

The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving f

tty/serial: Migrate 8250_fsl to use has_sysrq

The SUPPORT_SYSRQ ifdeffery is not nice as:
- May create misunderstanding about sizeof(struct uart_port) between
different objects
- Prevents moving functions from serial_core.h
- Reduces readability (well, it's ifdeffery - it's hard to follow)

In order to remove SUPPORT_SYSRQ, has_sysrq variable has been added.
Initialise it in driver's probe and remove ifdeffery.

In contrast to 8250/8250_of, legacy_serial on powerpc does fill
(struct plat_serial8250_port). The reason is likely that it's done on
device_initcall(), not on probe. So, 8250_core is not yet probed.

Propagate value from platform_device on 8250 probe - in case powepc
legacy driver it's initialized on initcall, in case 8250_of it will be
initialized later on of_platform_serial_setup().

Cc: Benjamin Herrenschmidt <benh@kernel.crashing.org>
Cc: Paul Mackerras <paulus@samba.org>
Cc: Michael Ellerman <mpe@ellerman.id.au>
Cc: linuxppc-dev@lists.ozlabs.org
Signed-off-by: Dmitry Safonov <dima@arista.com>
Link: https://lore.kernel.org/r/20191213000657.931618-6-dima@arista.com
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

tty/serial/8250: use mctrl_gpio helpers

This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.

Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no AC

tty/serial/8250: use mctrl_gpio helpers

This patch permits the usage for GPIOs to control
the CTS/RTS/DTR/DSR/DCD/RI signals.

Changed by Stefan:
Only call mctrl_gpio_init(), if the device has no ACPI companion device
to not break existing ACPI based systems. Also only use the mctrl_gpio_
functions when "gpios" is available.

Use MSR / MCR <-> TIOCM wrapper functions.

Signed-off-by: Yegor Yefremov <yegorslists@googlemail.com>
Signed-off-by: Stefan Roese <sr@denx.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Mika Westerberg <mika.westerberg@linux.intel.com>
Tested-by: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Mika Westerberg <mika.westerberg@linux.intel.com>
Cc: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Cc: Giulio Benetti <giulio.benetti@micronovasrl.com>
Cc: Yegor Yefremov <yegorslists@googlemail.com>
Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 152

Based on 1 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 3029 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070032.746973796@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: Rate limit serial port rx interrupts during input overruns

When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the chara

serial: 8250: Rate limit serial port rx interrupts during input overruns

When a serial port gets faulty or gets flooded with inputs, its interrupt
handler starts to work double time to get the characters to the workqueue
for the tty layer to handle them. When this busy time on the serial/tty
subsystem happens during boot, where it is also busy on the userspace
trying to initialise, some processes can continuously get preempted
and will be on hold until the interrupts subside.

The fix is to backoff on processing received characters for a specified
amount of time when an input overrun is seen (received a new character
before the previous one is processed). This only stops receive and will
continue to transmit characters to serial port. After the backoff period
is done, it receive will be re-enabled. This is optional and will only
be enabled by setting 'overrun-throttle-ms' in the dts.

Signed-off-by: Darwin Dingel <darwin.dingel@alliedtelesis.co.nz>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

serial: 8250: export serial8250_do_set_divisor()

Some drivers could call serial8250_do_set_divisor() to complete its
own set_divisor routine. Export this symbol for code reusing.

Signed-off-by: Jis

serial: 8250: export serial8250_do_set_divisor()

Some drivers could call serial8250_do_set_divisor() to complete its
own set_divisor routine. Export this symbol for code reusing.

Signed-off-by: Jisheng Zhang <Jisheng.Zhang@synaptics.com>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...