usb: misc: Add onboard_usb_hub driver

The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is

usb: misc: Add onboard_usb_hub driver

The main issue this driver addresses is that a USB hub needs to be
powered before it can be discovered. For discrete onboard hubs (an
example for such a hub is the Realtek RTS5411) this is often solved
by supplying the hub with an 'always-on' regulator, which is kind
of a hack. Some onboard hubs may require further initialization
steps, like changing the state of a GPIO or enabling a clock, which
requires even more hacks. This driver creates a platform device
representing the hub which performs the necessary initialization.
Currently it only supports switching on a single regulator, support
for multiple regulators or other actions can be added as needed.
Different initialization sequences can be supported based on the
compatible string.

Besides performing the initialization the driver can be configured
to power the hub off during system suspend. This can help to extend
battery life on battery powered devices which have no requirements
to keep the hub powered during suspend. The driver can also be
configured to leave the hub powered when a wakeup capable USB device
is connected when suspending, and power it off otherwise.

Technically the driver consists of two drivers, the platform driver
described above and a very thin USB driver that subclasses the
generic driver. The purpose of this driver is to provide the platform
driver with the USB devices corresponding to the hub(s) (a hub
controller may provide multiple 'logical' hubs, e.g. one to support
USB 2.0 and another for USB 3.x).

Co-developed-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Reviewed-by: Douglas Anderson <dianders@chromium.org>
Signed-off-by: Ravi Chandra Sadineni <ravisadineni@chromium.org>
Signed-off-by: Matthias Kaehlcke <mka@chromium.org>
Link: https://lore.kernel.org/r/20220630123445.v24.3.I7c9a1f1d6ced41dd8310e8a03da666a32364e790@changeid
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: core: add a wrapper for the USB PHYs on the HCD

Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to

usb: core: add a wrapper for the USB PHYs on the HCD

Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to make the USB controller actually work. They also have to be
disabled again on shutdown/suspend.

Currently (at least) the following HCI platform drivers are using custom
code to obtain all PHYs via devicetree for the roothub/controller and
disable/enable them when required:
- ehci-platform.c has ehci_platform_power_{on,off}
- xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
- ohci-platform.c has ohci_platform_power_{on,off}

With this new wrapper the USB PHYs can be specified directly in the
USB controller's devicetree node (just like on the drivers listed
above). This allows SoCs like the Amlogic Meson GXL family to operate
correctly once this is wired up correctly. These SoCs use a dwc3
controller and require all USB PHYs to be initialized (if one of the USB
PHYs it not initialized then none of USB port works at all).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: add CONFIG_USB_PCI for system have both PCI HW and non-PCI based USB HW

a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registe

usb: add CONFIG_USB_PCI for system have both PCI HW and non-PCI based USB HW

a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.

when say N here it will not build PCI related code in USB driver.

Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: core: Introduce a USB port LED trigger

This commit adds a new trigger responsible for turning on LED when USB
device gets connected to the selected USB port. This can can useful for
various hom

usb: core: Introduce a USB port LED trigger

This commit adds a new trigger responsible for turning on LED when USB
device gets connected to the selected USB port. This can can useful for
various home routers that have USB port(s) and a proper LED telling user
a device is connected.

The trigger gets its documentation file but basically it just requires
enabling it and selecting USB ports (e.g. echo 1 > ports/usb1-1).

There was a long discussion on design of this driver. Its current state
is a result of picking them most adjustable solution as others couldn't
handle all cases.

1) It wasn't possible for the driver to register separated trigger for
each USB port. Some physical USB ports are handled by more than one
controller and so by more than one USB port. E.g. USB 2.0 physical
port may be handled by OHCI's port and EHCI's port.
It's also not possible to assign more than 1 trigger to a single LED
and implementing such feature would be tricky due to syncing triggers
and sysfs conflicts with old triggers.

2) Another idea was to register trigger per USB hub. This wouldn't allow
handling devices with multiple USB LEDs and controllers (hubs)
controlling more than 1 physical port. It's common for hubs to have
few ports and each may have its own LED.

This final trigger is highly flexible. It allows selecting any USB ports
for any LED. It was also modified (comparing to the initial version) to
allow choosing ports rather than having user /guess/ proper names. It
was successfully tested on SmartRG SR400ac which has 3 USB LEDs,
2 physical ports and 3 controllers.

It was noted USB subsystem already has usb-gadget and usb-host triggers
but they are pretty trivial ones. They indicate activity only and can't
have ports specified.

In future it may be good idea to consider adding activity support to
usbport as well. This should allow switching to this more generic driver
and maybe marking old ones as obsolete.
This can be implemented with another sysfs file for setting mode. The
default mode wouldn't change so there won't be ABI breakage and so such
feature can be safely implemented later.

There was also an idea of supporting other devices (PCI, SDIO, etc.) but
as this driver already contains some USB specific code (and will get
more) these should be probably separated drivers (triggers).

Signed-off-by: Rafał Miłecki <rafal@milecki.pl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: core: of.c: fix defined but not declare warning

The helper usb_of_get_child_node is defined at of.c, but missing its
declare as a global function. Fix it by adding related header file
as well a

usb: core: of.c: fix defined but not declare warning

The helper usb_of_get_child_node is defined at of.c, but missing its
declare as a global function. Fix it by adding related header file
as well as compile it on conditional of CONFIG_OF.

Cc: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Cc: Arnd Bergmann <arnd@arndb.de>
Cc: Alan Stern <stern@rowland.harvard.edu>
Cc: linux-usb@vger.kernel.org
Cc: linux-kernel@vger.kernel.org
Cc: Ben Dooks <ben.dooks@codethink.co.uk>
Cc: linux-kernel@lists.codethink.co.uk

Signed-off-by: Peter Chen <peter.chen@nxp.com>
Reported-by: Ben Dooks <ben.dooks@codethink.co.uk>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: core: let USB device know device node

Although most of USB devices are hot-plug's, there are still some devices
are hard wired on the board, eg, for HSIC and SSIC interface USB devices.
If thes

USB: core: let USB device know device node

Although most of USB devices are hot-plug's, there are still some devices
are hard wired on the board, eg, for HSIC and SSIC interface USB devices.
If these kinds of USB devices are multiple functions, and they can supply
other interfaces like i2c, gpios for other devices, we may need to
describe these at device tree.

In this commit, it uses "reg" in dts as physical port number to match
the phyiscal port number decided by USB core, if they are the same,
then the device node is for the device we are creating for USB core.

Signed-off-by: Peter Chen <peter.chen@freescale.com>
Acked-by: Philipp Zabel <p.zabel@pengutronix.de>
Acked-by: Alan Stern <stern@rowland.harvard.edu>
Acked-by: Rob Herring <robh@kernel.org>
Acked-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: core: remove CONFIG_USB_DEBUG usage

CONFIG_USB_DEBUG is going away, so remove the few places in the USB core
that relied on them.

This means that we always now do the "debug" checks for every

USB: core: remove CONFIG_USB_DEBUG usage

CONFIG_USB_DEBUG is going away, so remove the few places in the USB core
that relied on them.

This means that we always now do the "debug" checks for every urb
submitted, which is a good idea, as who knows how many driver bugs we
have been ignoring when people forget to enable this option. Also, with
the overall speed of USB, doing these extra checks should not cause any
additional overhead.

Also, no longer announce all devices being added to the system if
CONFIG_USB_DEBUG is enabled, as it's not going to be around much longer.

Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: Add driver/usb/core/(port.c,hub.h) files

This patch is to create driver/usb/core/(port.c,hub.h) files and move usb
port related code into port.c.

Signed-off-by: Lan Tianyu <tianyu.lan@intel.co

usb: Add driver/usb/core/(port.c,hub.h) files

This patch is to create driver/usb/core/(port.c,hub.h) files and move usb
port related code into port.c.

Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: Bind devices to ACPI devices when possible

Built-in USB devices will typically have a representation in the system
ACPI tables. Add support for binding the two together so the USB code can
make

usb: Bind devices to ACPI devices when possible

Built-in USB devices will typically have a representation in the system
ACPI tables. Add support for binding the two together so the USB code can
make use of the associated methods.

Signed-off-by: Matthew Garrett <mjg@redhat.com>
Signed-off-by: Lan Tianyu <tianyu.lan@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

USB: remove CONFIG_USB_DEVICEFS

This option has been deprecated for many years now, and no userspace
tools use it anymore, so it should be safe to finally remove it.

Reported-by: Kay Sievers <kay@v

USB: remove CONFIG_USB_DEVICEFS

This option has been deprecated for many years now, and no userspace
tools use it anymore, so it should be safe to finally remove it.

Reported-by: Kay Sievers <kay@vrfy.org>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: makefile cleanup

For all modules, change <module>-objs to <module>-y; remove
if-statements and replace with lists using the kbuild idiom; move
flags to the top of the file; and fix alignment wh

usb: makefile cleanup

For all modules, change <module>-objs to <module>-y; remove
if-statements and replace with lists using the kbuild idiom; move
flags to the top of the file; and fix alignment while trying to
maintain the original scheme in each file.

None of the dependencies are modified.

Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: Sam Ravnborg <sam@ravnborg.org>
Acked-by: Felipe Balbi <balbi@ti.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

usb: change to new flag variable

Replace EXTRA_CFLAGS with ccflags-y.

Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Greg Kroah-Hartman

usb: change to new flag variable

Replace EXTRA_CFLAGS with ccflags-y.

Signed-off-by: matt mooney <mfm@muteddisk.com>
Acked-by: WANG Cong <xiyou.wangcong@gmail.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

USB: add the usbfs devices file to debugfs

People are very used to the devices file in usbfs. Now that we have
moved usbfs to be an "embedded" option only, the developers miss the
file, they had gr

USB: add the usbfs devices file to debugfs

People are very used to the devices file in usbfs. Now that we have
moved usbfs to be an "embedded" option only, the developers miss the
file, they had grown quite attached to it over all of these years. This
patch brings it back and puts it in the usb debugfs directory, so that
the developers don't feel sad anymore.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

USB: add a blacklist for devices that can't handle some things we throw at them.

This adds a blacklist to the USB core to handle some autosuspend and
string issues that devices have.

Originally wri

USB: add a blacklist for devices that can't handle some things we throw at them.

This adds a blacklist to the USB core to handle some autosuspend and
string issues that devices have.

Originally written by Oliver, but hacked up a lot by Greg.

Signed-off-by: Oliver Neukum <oneukum@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

usbcore: move code among source files

This revised patch (as713b) moves a few routines among source files in
usbcore. Some driver-related code in usb.c (claiming interfaces and
matching IDs) is mov

usbcore: move code among source files

This revised patch (as713b) moves a few routines among source files in
usbcore. Some driver-related code in usb.c (claiming interfaces and
matching IDs) is moved to driver.c, where it belongs. Also the
usb_generic stuff in driver.c is moved to a new source file: generic.c.
(That's the reason for revising the patch.) Although not very big now,
it will get bigger in a later patch.

None of the code has been changed; it has only been re-arranged.


Signed-off-by: Alan Stern <stern@rowland.harvard.edu>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

[PATCH] USB: move the endpoint specific sysfs code to it's own file

This makes it easier to modify in the future without touching anything else.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

[PATCH] USB: reorg some functions out of the main usb.c file

This will make the dynamic-id stuff easier to do, as it will be
self-contained.

No logic was changed at all.

Signed-off-by: Greg Kroah-

[PATCH] USB: reorg some functions out of the main usb.c file

This will make the dynamic-id stuff easier to do, as it will be
self-contained.

No logic was changed at all.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

[PATCH] USB: move CONFIG_USB_DEBUG checks into the Makefile

This lets us remove a lot of code in the drivers that were all checking
the same thing. It also found some bugs in a few of the drivers,

[PATCH] USB: move CONFIG_USB_DEBUG checks into the Makefile

This lets us remove a lot of code in the drivers that were all checking
the same thing. It also found some bugs in a few of the drivers, which
has been fixed up.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>
Signed-off-by: Linus Torvalds <torvalds@osdl.org>

show more ...

[PATCH] USB: add notifier functions to the USB core for devices and busses

This should let us get rid of all of the different hooks in the USB core for
when something has changed.

Also, some other

[PATCH] USB: add notifier functions to the USB core for devices and busses

This should let us get rid of all of the different hooks in the USB core for
when something has changed.

Also, some other parts of the kernel have wanted to know this kind of
information at times.

Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

[PATCH] USB: real nodes instead of usbfs

This patch introduces a /sys/class/usb_device/ class
where every connected usb-device will show up:

tree /sys/class/usb_device/
/sys/class/usb_device/

[PATCH] USB: real nodes instead of usbfs

This patch introduces a /sys/class/usb_device/ class
where every connected usb-device will show up:

tree /sys/class/usb_device/
/sys/class/usb_device/
|-- usb1.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.0/usb1
|-- usb2.1
| |-- dev
| `-- device -> ../../../devices/pci0000:00/0000:00:1d.1/usb2
...

The presence of the "dev" file lets udev create real device nodes.
kay@pim:~/src/linux-2.6> tree /dev/bus/usb/
/dev/bus/usb/
|-- 1
| `-- 1
|-- 2
| `-- 1
...

udev rule:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usb_device %k", NAME="%c"
(echo $1 | /bin/sed 's/usb\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/')

This makes libusb pick up the real nodes instead of the mounted usbfs:
export USB_DEVFS_PATH=/dev/bus/usb

Background:
All this makes it possible to manage usb devices with udev instead of
the devfs solution. We are currently working on a pam_console/resmgr
replacement driven by udev and a pam-helper. It applies ACL's to device
nodes, which is required for modern desktop functionalty like
"Fast User Switching" or multiple local login support.

New patch with its own major. I've succesfully disabled usbfs and use real
nodes only on my box. With: "export USB_DEVFS_PATH=/dev/bus/usb" libusb picks
up the udev managed nodes instead of reading usbfs files.

This makes udev to provide symlinks for libusb to pick up:
SUBSYSTEM="usb_device", PROGRAM="/sbin/usbdevice %k", SYMLINK="%c"

/sbin/usbdevice:
#!/bin/sh
echo $1 | /bin/sed 's/usbdev\([0-9]*\)\.\([0-9]*\)/bus\/usb\/\1\/\2/'

Signed-off-by: Kay Sievers <kay.sievers@suse.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@suse.de>

show more ...

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in

Linux-2.6.12-rc2

Initial git repository build. I'm not bothering with the full history,
even though we have it. We can create a separate "historical" git
archive of that later if we want to, and in the meantime it's about
3.2GB when imported into git - space that would just make the early
git days unnecessarily complicated, when we don't have a lot of good
infrastructure for it.

Let it rip!

show more ...

usb: core: add a wrapper for the USB PHYs on the HCD

Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to b

usb: core: add a wrapper for the USB PHYs on the HCD

Many SoC platforms have separate devices for the USB PHY which are
registered through the generic PHY framework. These PHYs have to be
enabled to make the USB controller actually work. They also have to be
disabled again on shutdown/suspend.

Currently (at least) the following HCI platform drivers are using custom
code to obtain all PHYs via devicetree for the roothub/controller and
disable/enable them when required:
- ehci-platform.c has ehci_platform_power_{on,off}
- xhci-mtk.c has xhci_mtk_phy_{init,exit,power_on,power_off}
- ohci-platform.c has ohci_platform_power_{on,off}

With this new wrapper the USB PHYs can be specified directly in the
USB controller's devicetree node (just like on the drivers listed
above). This allows SoCs like the Amlogic Meson GXL family to operate
correctly once this is wired up correctly. These SoCs use a dwc3
controller and require all USB PHYs to be initialized (if one of the USB
PHYs it not initialized then none of USB port works at all).

Signed-off-by: Martin Blumenstingl <martin.blumenstingl@googlemail.com>
Tested-by: Yixun Lan <yixun.lan@amlogic.com>
Cc: Chunfeng Yun <chunfeng.yun@mediatek.com>
Tested-by: Neil Armstrong <narmstrong@baylibre.con>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

usb: add CONFIG_USB_PCI for system have both PCI HW and non-PCI based USB HW

a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlle

usb: add CONFIG_USB_PCI for system have both PCI HW and non-PCI based USB HW

a lot of embeded system SOC (e.g. freescale T2080) have both
PCI and USB modules. But USB module is controlled by registers directly,
it have no relationship with PCI module.

when say N here it will not build PCI related code in USB driver.

Signed-off-by: yuan linyu <Linyu.Yuan@alcatel-sbell.com.cn>
Acked-by: Felipe Balbi <felipe.balbi@linux.intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...