regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14

Probing of regulators can be a slow operation and can contribute to
slower boot times. This is especially true if a regulato

regulator: Set PROBE_PREFER_ASYNCHRONOUS for drivers that existed in 4.14

Probing of regulators can be a slow operation and can contribute to
slower boot times. This is especially true if a regulator is turned on
at probe time (with regulator-boot-on or regulator-always-on) and the
regulator requires delays (off-on-time, ramp time, etc).

While the overall kernel is not ready to switch to async probe by
default, as per the discussion on the mailing lists [1] it is believed
that the regulator subsystem is in good shape and we can move
regulator drivers over wholesale. There is no way to just magically
opt in all regulators (regulators are just normal drivers like
platform_driver), so we set PROBE_PREFER_ASYNCHRONOUS for all
regulators found in 'drivers/regulator' individually.

Given the number of drivers touched and the impossibility to test this
ahead of time, it wouldn't be shocking at all if this caused a
regression for someone. If there is a regression caused by this patch,
it's likely to be one of the cases talked about in [1]. As a "quick
fix", drivers involved in the regression could be fixed by changing
them to PROBE_FORCE_SYNCHRONOUS. That being said, the correct fix
would be to directly fix the problem that caused the issue with async
probe.

The approach here follows a similar approach that was used for the mmc
subsystem several years ago [2]. In fact, I ran nearly the same python
script to auto-generate the changes. The only thing I changed was to
search for "i2c_driver", "spmi_driver", and "spi_driver" in addition
to "platform_driver".

[1] https://lore.kernel.org/r/06db017f-e985-4434-8d1d-02ca2100cca0@sirena.org.uk
[2] https://lore.kernel.org/r/20200903232441.2694866-1-dianders@chromium.org/

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Link: https://lore.kernel.org/r/20230316125351.1.I2a4677392a38db5758dee0788b2cea5872562a82@changeid
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Fix n_voltages setting for lm36274

According to the datasheet http://www.ti.com/lit/ds/symlink/lm36274.pdf:
Table 23. VPOS Bias Register Field Descriptions VPOS[5:0]:
VPOS voltage

regulator: lm363x: Fix n_voltages setting for lm36274

According to the datasheet http://www.ti.com/lit/ds/symlink/lm36274.pdf:
Table 23. VPOS Bias Register Field Descriptions VPOS[5:0]:
VPOS voltage (50-mV steps): VPOS = 4 V + (Code × 50 mV), 6.5 V max
000000 = 4 V
000001 = 4.05 V
:
011110 = 5.5 V (Default)
:
110010 = 6.5 V
110011 to 111111 map to 6.5 V

So the LM36274_LDO_VSEL_MAX should be 0b110010 (0x32).
The valid selectors are 0 ... LM36274_LDO_VSEL_MAX, n_voltages should be
LM36274_LDO_VSEL_MAX + 1. Similarly, the n_voltages should be
LM36274_BOOST_VSEL_MAX + 1 for LM36274_BOOST.

Fixes: bff5e8071533 ("regulator: lm363x: Add support for LM36274")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Fix off-by-one n_voltages for lm3632 ldo_vpos/ldo_vneg

According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPO

regulator: lm363x: Fix off-by-one n_voltages for lm3632 ldo_vpos/ldo_vneg

According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V

The LM3632_LDO_VSEL_MAX should be 0b101000 (0x28), so the maximum voltage
can match the datasheet.

Fixes: 3a8d1a73a037 ("regulator: add LM363X driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

regulator: lm363x: Add support for LM36274

Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers are common enough

regulator: lm363x: Add support for LM36274

Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers are common enough between the LM36274 and the LM363x
series of devices.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>

show more ...

regulator: lm363x: Constify regulator_ops

The lm363x_boost_voltage_table_ops and lm363x_regulator_voltage_table_ops
never need to be modified, make them const so compiler can put them to
.rodata.

S

regulator: lm363x: Constify regulator_ops

The lm363x_boost_voltage_table_ops and lm363x_regulator_voltage_table_ops
never need to be modified, make them const so compiler can put them to
.rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Use proper data type for regmap_read arguments

regmap_read() takes unsigned int reg and unsigned int *val arguments,
use proper data type for these arguments.

Signed-off-by: Axel

regulator: lm363x: Use proper data type for regmap_read arguments

regmap_read() takes unsigned int reg and unsigned int *val arguments,
use proper data type for these arguments.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Check return value of gpiod_get_index_optional

gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test for gpiod in

regulator: lm363x: Check return value of gpiod_get_index_optional

gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test for gpiod in error path.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Let core handle GPIO descriptor

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

Fixes: b2d751b7f69b (

regulator: lm363x: Let core handle GPIO descriptor

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

Fixes: b2d751b7f69b ("regulator: lm363x: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: Fetch enable gpiods nonexclusive

Since the core regulator code is treating GPIO descriptors as
nonexclusive, i.e. it assumes that the enable GPIO line may be
shared with several regulator

regulator: Fetch enable gpiods nonexclusive

Since the core regulator code is treating GPIO descriptors as
nonexclusive, i.e. it assumes that the enable GPIO line may be
shared with several regulators, let's add the flag introduced
for fixing this problem on fixed regulators to all drivers
fetching GPIO descriptors to avoid possible regressions.

Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Pass descriptor instead of GPIO number

Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.

Signed-off-by:

regulator: lm363x: Pass descriptor instead of GPIO number

Instead of passing a global GPIO number, pass a descriptor looked
up with the standard devm_gpiod_get_index_optional() call.

Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Use generic DT property name for external control pins

Vpos and Vneg LDOs can be enabled or disabled by external GPIOs.
Use general DT property 'enable-gpios' for this usage.
Two

regulator: lm363x: Use generic DT property name for external control pins

Vpos and Vneg LDOs can be enabled or disabled by external GPIOs.
Use general DT property 'enable-gpios' for this usage.
Two enable pins are differentiable by selecting the index number.

Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Staticise ldo_cont_enable_time

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: lm363x: Remove struct lm363x_regulator which is not necessary

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

regulator: add LM363X driver

LM363X regulator driver supports LM3631 and LM3632.
LM3631 has 5 regulators. LM3632 provides 3 regulators.
One boost output and LDOs are used for the display module.
Boo

regulator: add LM363X driver

LM363X regulator driver supports LM3631 and LM3632.
LM3631 has 5 regulators. LM3632 provides 3 regulators.
One boost output and LDOs are used for the display module.
Boost voltage is configurable but always on.
Supported operations for LDOs are enabled/disabled and voltage change.

Two LDOs of LM3632 can be controlled by external pins.
Those are configured through the DT properties.

Signed-off-by: Milo Kim <milo.kim@ti.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Fix n_voltages setting for lm36274

According to the datasheet http://www.ti.com/lit/ds/symlink/lm36274.pdf:
Table 23. VPOS Bias Register Field Descriptions VPOS[5:0]:

regulator: lm363x: Fix n_voltages setting for lm36274

According to the datasheet http://www.ti.com/lit/ds/symlink/lm36274.pdf:
Table 23. VPOS Bias Register Field Descriptions VPOS[5:0]:
VPOS voltage (50-mV steps): VPOS = 4 V + (Code × 50 mV), 6.5 V max
000000 = 4 V
000001 = 4.05 V
:
011110 = 5.5 V (Default)
:
110010 = 6.5 V
110011 to 111111 map to 6.5 V

So the LM36274_LDO_VSEL_MAX should be 0b110010 (0x32).
The valid selectors are 0 ... LM36274_LDO_VSEL_MAX, n_voltages should be
LM36274_LDO_VSEL_MAX + 1. Similarly, the n_voltages should be
LM36274_BOOST_VSEL_MAX + 1 for LM36274_BOOST.

Fixes: bff5e8071533 ("regulator: lm363x: Add support for LM36274")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-2-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Fix off-by-one n_voltages for lm3632 ldo_vpos/ldo_vneg

According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Desc

regulator: lm363x: Fix off-by-one n_voltages for lm3632 ldo_vpos/ldo_vneg

According to the datasheet https://www.ti.com/lit/ds/symlink/lm3632a.pdf
Table 20. VPOS Bias Register Field Descriptions VPOS[5:0]
Sets the Positive Display Bias (LDO) Voltage (50 mV per step)
000000: 4 V
000001: 4.05 V
000010: 4.1 V
....................
011101: 5.45 V
011110: 5.5 V (Default)
011111: 5.55 V
....................
100111: 5.95 V
101000: 6 V
Note: Codes 101001 to 111111 map to 6 V

The LM3632_LDO_VSEL_MAX should be 0b101000 (0x28), so the maximum voltage
can match the datasheet.

Fixes: 3a8d1a73a037 ("regulator: add LM363X driver")
Signed-off-by: Axel Lin <axel.lin@ingics.com>
Link: https://lore.kernel.org/r/20190626132632.32629-1-axel.lin@ingics.com
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

Merge tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:

- Add a new LED common module for ti-l

Merge tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds

Pull LED updates from Jacek Anaszewski:

- Add a new LED common module for ti-lmu driver family

- Modify MFD ti-lmu bindings
- add ti,brightness-resolution
- add the ramp up/down property

- Add regulator support for LM36274 driver to lm363x-regulator.c

- New LED class drivers with DT bindings:
- leds-spi-byte
- leds-lm36274
- leds-lm3697 (move the support from MFD to LED subsystem)

- Simplify getting the I2C adapter of a client:
- leds-tca6507
- leds-pca955x

- Convert LED documentation to ReST

* tag 'leds-for-5.3-rc1' of git://git.kernel.org/pub/scm/linux/kernel/git/j.anaszewski/linux-leds:
dt: leds-lm36274.txt: fix a broken reference to ti-lmu.txt
docs: leds: convert to ReST
leds: leds-tca6507: simplify getting the adapter of a client
leds: leds-pca955x: simplify getting the adapter of a client
leds: lm36274: Introduce the TI LM36274 LED driver
dt-bindings: leds: Add LED bindings for the LM36274
regulator: lm363x: Add support for LM36274
mfd: ti-lmu: Add LM36274 support to the ti-lmu
dt-bindings: mfd: Add lm36274 bindings to ti-lmu
leds: max77650: Remove set but not used variable 'parent'
leds: avoid flush_work in atomic context
leds: lm3697: Introduce the lm3697 driver
mfd: ti-lmu: Remove support for LM3697
dt-bindings: ti-lmu: Modify dt bindings for the LM3697
leds: TI LMU: Add common code for TI LMU devices
leds: spi-byte: add single byte SPI LED driver
dt-bindings: leds: Add binding for spi-byte LED.
dt-bindings: mfd: LMU: Add ti,brightness-resolution
dt-bindings: mfd: LMU: Add the ramp up/down property

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it u

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 500

Based on 2 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license version 2 as
published by the free software foundation #

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-only

has been chosen to replace the boilerplate/reference in 4122 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Enrico Weigelt <info@metux.net>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Allison Randal <allison@lohutok.net>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190604081206.933168790@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

regulator: lm363x: Add support for LM36274

Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers a

regulator: lm363x: Add support for LM36274

Adding regulator support for the LM36274 backlight driver.
This device can leverage this existing code as the functionality
and registers are common enough between the LM36274 and the LM363x
series of devices.

Signed-off-by: Dan Murphy <dmurphy@ti.com>
Acked-by: Mark Brown <broonie@kernel.org>
Acked-by: Pavel Machek <pavel@ucw.cz>
Signed-off-by: Jacek Anaszewski <jacek.anaszewski@gmail.com>

show more ...

regulator: lm363x: Constify regulator_ops

The lm363x_boost_voltage_table_ops and lm363x_regulator_voltage_table_ops
never need to be modified, make them const so compiler can put them to

regulator: lm363x: Constify regulator_ops

The lm363x_boost_voltage_table_ops and lm363x_regulator_voltage_table_ops
never need to be modified, make them const so compiler can put them to
.rodata.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Use proper data type for regmap_read arguments

regmap_read() takes unsigned int reg and unsigned int *val arguments,
use proper data type for these arguments.

regulator: lm363x: Use proper data type for regmap_read arguments

regmap_read() takes unsigned int reg and unsigned int *val arguments,
use proper data type for these arguments.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Check return value of gpiod_get_index_optional

gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test

regulator: lm363x: Check return value of gpiod_get_index_optional

gpiod_get_index_optional can return ERR_PTR, add IS_ERR checking for it.
While at it, also remove a redundant NULL test for gpiod in error path.

Signed-off-by: Axel Lin <axel.lin@ingics.com>
Acked-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: lm363x: Let core handle GPIO descriptor

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

F

regulator: lm363x: Let core handle GPIO descriptor

Use the gpiod_get() rather than the devm_* version so that the
regulator core can handle the lifecycle of these descriptors.

Fixes: b2d751b7f69b ("regulator: lm363x: Pass descriptor instead of GPIO number")
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Reviewed-by: Marek Szyprowski <m.szyprowski@samsung.com>
Reviewed-by: Charles Keepax <ckeepax@opensource.cirrus.com>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...

regulator: Fetch enable gpiods nonexclusive

Since the core regulator code is treating GPIO descriptors as
nonexclusive, i.e. it assumes that the enable GPIO line may be
shared with s

regulator: Fetch enable gpiods nonexclusive

Since the core regulator code is treating GPIO descriptors as
nonexclusive, i.e. it assumes that the enable GPIO line may be
shared with several regulators, let's add the flag introduced
for fixing this problem on fixed regulators to all drivers
fetching GPIO descriptors to avoid possible regressions.

Reported-by: Mark Brown <broonie@kernel.org>
Signed-off-by: Linus Walleij <linus.walleij@linaro.org>
Signed-off-by: Mark Brown <broonie@kernel.org>

show more ...