wifi: iwlwifi: mvm: report hardware timestamps in RX/TX status

For TM/FTM frames, report the hardware timestamps reported by the
fw as part of the RX/TX status. Since the fw reports the timestamps
i

wifi: iwlwifi: mvm: report hardware timestamps in RX/TX status

For TM/FTM frames, report the hardware timestamps reported by the
fw as part of the RX/TX status. Since the fw reports the timestamps
in a dedicated notification (and not as part of the RX/TX status),
hold the frame until the fw timestamps notification is received.
Timestamping is enabled when a station is connected and disabled
when disconnected. For AP interface, only the first station will
have timestamping enabled since the fw only supports timestamping
for one peer.

Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.e0392d498101.I9bf12c8ecfb3f17253a13dc48a48647ddd6e7855@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

wifi: iwlwifi: mvm: add support for PTP HW clock (PHC)

Add support to enable/disable PHC clock. The PHC clock includes support
for fetching the cross timestamp i.e. a non-atomic snapshot of the curr

wifi: iwlwifi: mvm: add support for PTP HW clock (PHC)

Add support to enable/disable PHC clock. The PHC clock includes support
for fetching the cross timestamp i.e. a non-atomic snapshot of the current
time from the hardware (WiFi device) clock and system clock (wall-clock)
simultaneously.

Signed-off-by: Krishnanand Prabhu <krishnanand.prabhu@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230320122330.ae1d64f513b9.Ib3b6ad61c9fa2fc5908f1e0d6f59f4af6eec1a77@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

wifi: iwlwifi: mvm: Add an add_interface() callback for mld mode

As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD ad

wifi: iwlwifi: mvm: Add an add_interface() callback for mld mode

As the MLD mode and its new APIs are introduced,
we've decided to add a new ieee80211_ops dedicated for
MLD callbacks. Add the MLD add_interface() callback
which uses the new MLD APIs added the previous patches.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.6adc29bff39b.I97ed469028009be9392dcc6f7b5ffbe45f4b2c43@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

wifi: iwlwifi: mvm: add support for the new STA related commands

As a part of the new MLD FW API changes, we have new commands for STA
related operations (add/remove/aux/disable tx).
Add structures

wifi: iwlwifi: mvm: add support for the new STA related commands

As a part of the new MLD FW API changes, we have new commands for STA
related operations (add/remove/aux/disable tx).
Add structures and enum definitions, along with part of the functions
that sends this commands.
This functions will be in used and more will be added in the next patches.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.132873ce015c.I7b12a77e5be066730762e6ceeeaa7190293c3df1@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

wifi: iwlwifi: mvm: add support for the new LINK command

As a part of the new MLD FW API changes, we have a new LINK command
to add/remove/configure a link.
Add structures and enum definitions, alon

wifi: iwlwifi: mvm: add support for the new LINK command

As a part of the new MLD FW API changes, we have a new LINK command
to add/remove/configure a link.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
These functions will be in used in the next patches.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.d7808329effb.I13bea2db206b78540bc866bc3ab755ad5be78c53@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

wifi: iwlwifi: mvm: add support for the new MAC CTXT command

As a part of the new MLD FW API changes, we have a new MAC CTXT command.
Add structures and enum definitions, along with the functions th

wifi: iwlwifi: mvm: add support for the new MAC CTXT command

As a part of the new MLD FW API changes, we have a new MAC CTXT command.
Add structures and enum definitions, along with the functions that
sends this command (i.e. add, remove and change mac ctxt).
This functions will be in used in the next patches.

Signed-off-by: Miri Korenblit <miriam.rachel.korenblit@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20230314194113.99a41a5bc55f.I310312c829f5f2f69b64fcddce487b1eab80165b@changeid
Signed-off-by: Johannes Berg <johannes.berg@intel.com>

show more ...

wifi: iwlwifi: mvm: support new key API

In order to support MLD, the key API is also changing to have
station masks instead of just the station ID etc. Change the
driver to support this, and add the

wifi: iwlwifi: mvm: support new key API

In order to support MLD, the key API is also changing to have
station masks instead of just the station ID etc. Change the
driver to support this, and add the new code in a new file so
it's more clearly separated.

For now this isn't separated at the mac80211 ops level, which
we wanted to do, but we're calling these functions in a place
when pre-start keys are installed in iwl_mvm_start_ap_ibss(),
and the function has some glue logic to mac80211. We may want
to change that later.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Link: https://lore.kernel.org/r/20221102165239.ed9ccd814abc.Iacc7360de68807fbac19e5b67c86504b39cc15df@changeid

show more ...

iwlwifi: mvm: add vendor commands needed for iwlmei

Add the vendor commands that must be used by the network manager
to allow proper operation of iwlmei.

* Send information on the AP CSME is connec

iwlwifi: mvm: add vendor commands needed for iwlmei

Add the vendor commands that must be used by the network manager
to allow proper operation of iwlmei.

* Send information on the AP CSME is connected to
* Notify the userspace when roaming is forbidden
* Allow the userspace to require ownership

Co-Developed-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Ayala Beker <ayala.beker@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

v6: remove the VENDOR_CMDS Kconfig option and make the whole infra
depend on IWLMEI directly
v7: remove // comments
remove an unneeded function
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>
Link: https://lore.kernel.org/r/20211112062814.7502-5-emmanuel.grumbach@intel.com

show more ...

iwlwifi: mvm: add RFI-M support

RF Interference Mitigation is a new feature targeted to handle the
problem of interference between DDR memory and WiFi. The role of
the driver is to configure FW with

iwlwifi: mvm: add RFI-M support

RF Interference Mitigation is a new feature targeted to handle the
problem of interference between DDR memory and WiFi. The role of
the driver is to configure FW with the table holding a mapping
between problematic channels/bands and the corresponding frequencies.

This patch adds RFI infrastructure and adds two debugfs hooks:
- send RFI configuration command (currently with a default table) which
will reset feature in the FW
- read the table, used by the FW (which can be a subset of the table
that driver sent).

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>
Link: https://lore.kernel.org/r/iwlwifi.20210210171218.2cea55a09bc7.I634b79795abad499ce442631d6672ffef8fc6d41@changeid
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

iwlwifi: mvm: support FTM initiator

Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.

Additionally, add two defines we depend on in
include/linux/ieee8021

iwlwifi: mvm: support FTM initiator

Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.

Additionally, add two defines we depend on in
include/linux/ieee80211.h.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

iwlwifi: mvm: support FTM responder

Add support for FTM responder for hardware/firmware combinations
that advertise support for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off

iwlwifi: mvm: support FTM responder

Add support for FTM responder for hardware/firmware combinations
that advertise support for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

wireless: prefix header search paths with $(srctree)/

Currently, the Kbuild core manipulates header search paths in a crazy
way [1].

To fix this mess, I want all Makefiles to add explicit $(srctree

wireless: prefix header search paths with $(srctree)/

Currently, the Kbuild core manipulates header search paths in a crazy
way [1].

To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.

Having whitespaces after -I does not matter since commit 48f6e3cf5bc6
("kbuild: do not drop -I without parameter").

I also removed one header search path in:

drivers/net/wireless/broadcom/brcm80211/brcmutil/Makefile

I was able to compile without it.

[1]: https://patchwork.kernel.org/patch/9632347/

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

show more ...

iwlwifi: remove TOF implementation

This is an ancient (~2015) implementation that no longer matches
the firmware in any way, and most likely never worked. Remove all
of it so it can be reintroduced

iwlwifi: remove TOF implementation

This is an ancient (~2015) implementation that no longer matches
the firmware in any way, and most likely never worked. Remove all
of it so it can be reintroduced properly.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

iwlwifi: mvm: rs: add ops for the new rate scaling in the FW

This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the

iwlwifi: mvm: rs: add ops for the new rate scaling in the FW

This patch introduces a new instance of rate_control_ops for
the new API (adding only empty stubs here and the subsequent
patches in the series will fill in the implementation).
The decision which API to use is done during the register
step according to FW TLV.

Signed-off-by: Gregory Greenman <gregory.greenman@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine

License cleanup: add SPDX GPL-2.0 license identifier to files with no license

Many source files in the tree are missing licensing information, which
makes it harder for compliance tools to determine the correct license.

By default all files without license information are under the default
license of the kernel, which is GPL version 2.

Update the files which contain no license information with the 'GPL-2.0'
SPDX license identifier. The SPDX identifier is a legally binding
shorthand, which can be used instead of the full boiler plate text.

This patch is based on work done by Thomas Gleixner and Kate Stewart and
Philippe Ombredanne.

How this work was done:

Patches were generated and checked against linux-4.14-rc6 for a subset of
the use cases:
- file had no licensing information it it.
- file was a */uapi/* one with no licensing information in it,
- file was a */uapi/* one with existing licensing information,

Further patches will be generated in subsequent months to fix up cases
where non-standard license headers were used, and references to license
had to be inferred by heuristics based on keywords.

The analysis to determine which SPDX License Identifier to be applied to
a file was done in a spreadsheet of side by side results from of the
output of two independent scanners (ScanCode & Windriver) producing SPDX
tag:value files created by Philippe Ombredanne. Philippe prepared the
base worksheet, and did an initial spot review of a few 1000 files.

The 4.13 kernel was the starting point of the analysis with 60,537 files
assessed. Kate Stewart did a file by file comparison of the scanner
results in the spreadsheet to determine which SPDX license identifier(s)
to be applied to the file. She confirmed any determination that was not
immediately clear with lawyers working with the Linux Foundation.

Criteria used to select files for SPDX license identifier tagging was:
- Files considered eligible had to be source code files.
- Make and config files were included as candidates if they contained >5
lines of source
- File already had some variant of a license header in it (even if <5
lines).

All documentation files were explicitly excluded.

The following heuristics were used to determine which SPDX license
identifiers to apply.

- when both scanners couldn't find any license traces, file was
considered to have no license information in it, and the top level
COPYING file license applied.

For non */uapi/* files that summary was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 11139

and resulted in the first patch in this series.

If that file was a */uapi/* path one, it was "GPL-2.0 WITH
Linux-syscall-note" otherwise it was "GPL-2.0". Results of that was:

SPDX license identifier # files
---------------------------------------------------|-------
GPL-2.0 WITH Linux-syscall-note 930

and resulted in the second patch in this series.

- if a file had some form of licensing information in it, and was one
of the */uapi/* ones, it was denoted with the Linux-syscall-note if
any GPL family license was found in the file or had no licensing in
it (per prior point). Results summary:

SPDX license identifier # files
---------------------------------------------------|------
GPL-2.0 WITH Linux-syscall-note 270
GPL-2.0+ WITH Linux-syscall-note 169
((GPL-2.0 WITH Linux-syscall-note) OR BSD-2-Clause) 21
((GPL-2.0 WITH Linux-syscall-note) OR BSD-3-Clause) 17
LGPL-2.1+ WITH Linux-syscall-note 15
GPL-1.0+ WITH Linux-syscall-note 14
((GPL-2.0+ WITH Linux-syscall-note) OR BSD-3-Clause) 5
LGPL-2.0+ WITH Linux-syscall-note 4
LGPL-2.1 WITH Linux-syscall-note 3
((GPL-2.0 WITH Linux-syscall-note) OR MIT) 3
((GPL-2.0 WITH Linux-syscall-note) AND MIT) 1

and that resulted in the third patch in this series.

- when the two scanners agreed on the detected license(s), that became
the concluded license(s).

- when there was disagreement between the two scanners (one detected a
license but the other didn't, or they both detected different
licenses) a manual inspection of the file occurred.

- In most cases a manual inspection of the information in the file
resulted in a clear resolution of the license that should apply (and
which scanner probably needed to revisit its heuristics).

- When it was not immediately clear, the license identifier was
confirmed with lawyers working with the Linux Foundation.

- If there was any question as to the appropriate license identifier,
the file was flagged for further research and to be revisited later
in time.

In total, over 70 hours of logged manual review was done on the
spreadsheet to determine the SPDX license identifiers to apply to the
source files by Kate, Philippe, Thomas and, in some cases, confirmation
by lawyers working with the Linux Foundation.

Kate also obtained a third independent scan of the 4.13 code base from
FOSSology, and compared selected files where the other two scanners
disagreed against that SPDX file, to see if there was new insights. The
Windriver scanner is based on an older version of FOSSology in part, so
they are related.

Thomas did random spot checks in about 500 files from the spreadsheets
for the uapi headers and agreed with SPDX license identifier in the
files he inspected. For the non-uapi files Thomas did random spot checks
in about 15000 files.

In initial set of patches against 4.14-rc6, 3 files were found to have
copy/paste license identifier errors, and have been fixed to reflect the
correct identifier.

Additionally Philippe spent 10 hours this week doing a detailed manual
inspection and review of the 12,461 patched files from the initial patch
version early this week with:
- a full scancode scan run, collecting the matched texts, detected
license ids and scores
- reviewing anything where there was a license detected (about 500+
files) to ensure that the applied SPDX license was correct
- reviewing anything where there was no detection but the patch license
was not GPL-2.0 WITH Linux-syscall-note to ensure that the applied
SPDX license was correct

This produced a worksheet with 20 files needing minor correction. This
worksheet was then exported into 3 different .csv files for the
different types of files to be modified.

These .csv files were then reviewed by Greg. Thomas wrote a script to
parse the csv files and add the proper SPDX tag to the file, in the
format that the file expected. This script was further refined by Greg
based on the output to detect more types of files automatically and to
distinguish between header and source .c files (which need different
comment types.) Finally Greg ran the script using the .csv files to
generate the patches.

Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Reviewed-by: Philippe Ombredanne <pombredanne@nexb.com>
Reviewed-by: Thomas Gleixner <tglx@linutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

iwlwifi: refactor firmware debug code

Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Si

iwlwifi: refactor firmware debug code

Split out the firmware debug code to be more general, so that it
can be used by different subdrivers.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

Makefile: drop -D__CHECK_ENDIAN__ from cflags

That's the default now, no need for makefiles to set it.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>

Makefile: drop -D__CHECK_ENDIAN__ from cflags

That's the default now, no need for makefiles to set it.

Signed-off-by: Michael S. Tsirkin <mst@redhat.com>
Acked-by: Kalle Valo <kvalo@codeaurora.org>
Acked-by: Marcel Holtmann <marcel@holtmann.org>
Acked-by: Marc Kleine-Budde <mkl@pengutronix.de>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Arend van Spriel <arend.vanspriel@broadcom.com>

show more ...

iwlwifi: remove support for fw older than -16.ucode

API version lower than 16 is not supported anymore - don't
load older ucode.
Remove code handling older versions.

Signed-off-by: Sara Sharon <sar

iwlwifi: remove support for fw older than -16.ucode

API version lower than 16 is not supported anymore - don't
load older ucode.
Remove code handling older versions.

Signed-off-by: Sara Sharon <sara.sharon@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

show more ...

iwlwifi: update key params on d0i3 entrance/exit

In order to let the fw do offloading properly, we need
to provide various key data (e.g. PN).

Configure the params on d0i3 entrance, and update them

iwlwifi: update key params on d0i3 entrance/exit

In order to let the fw do offloading properly, we need
to provide various key data (e.g. PN).

Configure the params on d0i3 entrance, and update them
back on d0i3 exit.

Since d3 code is now called in d0i3 which requires runtime
pm only, make d3.0 depend on CONFIG_PM (rather than
CONFIG_PM_SLEEP), and add required #ifdefs and wrappers
where needed, so both CONFIG_PM=n and CONFIG_PM_RUNTIME=n
configurations will build correctly.

Signed-off-by: Eliad Peller <eliadx.peller@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

show more ...

iwlwifi: mvm: add 9000 series RX processing

Convert the convert the new infrastructure added by previous
patches to actually use the new RX descriptor layout.

Signed-off-by: Johannes Berg <johannes

iwlwifi: mvm: add 9000 series RX processing

Convert the convert the new infrastructure added by previous
patches to actually use the new RX descriptor layout.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

show more ...

iwlwifi: mvm: move fw-dbg code to separate file

The fw debug functionality is big enough to warrant
a separate file. Move existing related functions to the new file.

Signed-off-by: Golan Ben-Ami <g

iwlwifi: mvm: move fw-dbg code to separate file

The fw debug functionality is big enough to warrant
a separate file. Move existing related functions to the new file.

Signed-off-by: Golan Ben-Ami <golan.ben.ami@intel.com>
Signed-off-by: Emmanuel Grumbach <emmanuel.grumbach@intel.com>

show more ...

iwlwifi: move under intel vendor directory

Part of reorganising wireless drivers directory and Kconfig.

Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

iwlwifi: mvm: support FTM initiator

Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.

Additionally, add two defines we depend on in

iwlwifi: mvm: support FTM initiator

Add support for FTM initiator, i.e. peer measurements with FTM
if the firmware supports FTM.

Additionally, add two defines we depend on in
include/linux/ieee80211.h.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

iwlwifi: mvm: support FTM responder

Add support for FTM responder for hardware/firmware combinations
that advertise support for it.

Signed-off-by: Johannes Berg <johannes.berg@i

iwlwifi: mvm: support FTM responder

Add support for FTM responder for hardware/firmware combinations
that advertise support for it.

Signed-off-by: Johannes Berg <johannes.berg@intel.com>
Signed-off-by: Avraham Stern <avraham.stern@intel.com>
Signed-off-by: Luca Coelho <luciano.coelho@intel.com>

show more ...

wireless: prefix header search paths with $(srctree)/

Currently, the Kbuild core manipulates header search paths in a crazy
way [1].

To fix this mess, I want all Makefiles to ad

wireless: prefix header search paths with $(srctree)/

Currently, the Kbuild core manipulates header search paths in a crazy
way [1].

To fix this mess, I want all Makefiles to add explicit $(srctree)/ to
the search paths in the srctree. Some Makefiles are already written in
that way, but not all. The goal of this work is to make the notation
consistent, and finally get rid of the gross hacks.

Having whitespaces after -I does not matter since commit 48f6e3cf5bc6
("kbuild: do not drop -I without parameter").

I also removed one header search path in:

drivers/net/wireless/broadcom/brcm80211/brcmutil/Makefile

I was able to compile without it.

[1]: https://patchwork.kernel.org/patch/9632347/

Signed-off-by: Masahiro Yamada <yamada.masahiro@socionext.com>
Acked-by: Luca Coelho <luciano.coelho@intel.com>
Signed-off-by: Kalle Valo <kvalo@codeaurora.org>

show more ...