net: phy: nxp-tja11xx: constify pointers to hwmon_channel_info

Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.

Signed-off-by: Krzysztof Kozlowski <krzyszto

net: phy: nxp-tja11xx: constify pointers to hwmon_channel_info

Statically allocated array of pointed to hwmon_channel_info can be made
const for safety.

Signed-off-by: Krzysztof Kozlowski <krzysztof.kozlowski@linaro.org>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Link: https://lore.kernel.org/r/20230407145911.79642-7-krzysztof.kozlowski@linaro.org
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: tja11xx: add interface mode and RMII REF_CLK support

Add below features support for both TJA1100 and TJA1101 cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for

net: phy: tja11xx: add interface mode and RMII REF_CLK support

Add below features support for both TJA1100 and TJA1101 cards:
- Add MII and RMII mode support.
- Add REF_CLK input/output support for RMII mode.

Signed-off-by: Wei Fang <wei.fang@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: nxp-tja11xx: use devm_hwmon_sanitize_name()

Instead of open-coding the bad characters replacement in the hwmon name,
use the new devm_hwmon_sanitize_name().

Signed-off-by: Michael Walle <

net: phy: nxp-tja11xx: use devm_hwmon_sanitize_name()

Instead of open-coding the bad characters replacement in the hwmon name,
use the new devm_hwmon_sanitize_name().

Signed-off-by: Michael Walle <michael@walle.cc>
Acked-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: nxp-tja11xx: log critical health state

TJA1102 provides interrupt notification for the critical health states
like overtemperature and undervoltage.

The overtemperature bit is set if pack

net: phy: nxp-tja11xx: log critical health state

TJA1102 provides interrupt notification for the critical health states
like overtemperature and undervoltage.

The overtemperature bit is set if package temperature is beyond 155C°.
This functionality was tested by heating the package up to 200C°

The undervoltage bit is set if supply voltage drops beyond some critical
threshold. Currently not tested.

In a typical use case, both of this events should be logged and stored
(or send to some remote system) for further investigations.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: nxp-tja11xx: remove the use of .ack_interrupt()

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where

net: phy: nxp-tja11xx: remove the use of .ack_interrupt()

In preparation of removing the .ack_interrupt() callback, we must replace
its occurrences (aka phy_clear_interrupt), from the 2 places where it is
called from (phy_enable_interrupts and phy_disable_interrupts), with
equivalent functionality.

This means that clearing interrupts now becomes something that the PHY
driver is responsible of doing, before enabling interrupts and after
clearing them. Make this driver follow the new contract.

Cc: Marek Vasut <marex@denx.de>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: phy: nxp-tja11xx: implement generic .handle_interrupt() callback

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine o

net: phy: nxp-tja11xx: implement generic .handle_interrupt() callback

In an attempt to actually support shared IRQs in phylib, we now move the
responsibility of triggering the phylib state machine or just returning
IRQ_NONE, based on the IRQ status register, to the PHY driver. Having
3 different IRQ handling callbacks (.handle_interrupt(),
.did_interrupt() and .ack_interrupt() ) is confusing so let the PHY
driver implement directly an IRQ handler like any other device driver.
Make this driver follow the new convention.

Cc: Marek Vasut <marex@denx.de>
Cc: Oleksij Rempel <o.rempel@pengutronix.de>
Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: ethtool: Add generic parts of cable test TDR

Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new dri

net: ethtool: Add generic parts of cable test TDR

Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2
Update nxp-tja11xx for API change.

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add SQI support

This patch implements reading of the Signal Quality Index for better
cable/link troubleshooting.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-

net: phy: tja11xx: add SQI support

This patch implements reading of the Signal Quality Index for better
cable/link troubleshooting.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: execute cable test on link up

A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be able
to aut

net: phy: tja11xx: execute cable test on link up

A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be able
to automatically handle this issue, but we need to log it or notify user
(if possible).

With this patch, the cable will be tested on "ip l s dev .. up" attempt
and send ethnl notification to the user space.

This patch was tested with TJA1102 PHY and "ethtool --monitor" command.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add cable-test support

Add initial cable testing support.
This PHY needs only 100usec for this test and it is recommended to run it
before the link is up. For now, provide at leas

net: phy: tja11xx: add cable-test support

Add initial cable testing support.
This PHY needs only 100usec for this test and it is recommended to run it
before the link is up. For now, provide at least ethtool support, so it
can be tested by more developers.

This patch was tested with TJA1102 PHY with following results:
- No cable, is detected as open
- 1m cable, with no connected other end and detected as open
- a 40m cable (out of spec, max lenght should be 15m) is detected as OK.

Current patch do not provide polarity test support. This test would
indicate not proper wire connection, where "+" wire of main phy is
connected to the "-" wire of the link partner.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add support for master-slave configuration

The TJA11xx PHYs have a vendor specific Master/Slave configuration bit,
which is not compatible with IEEE 803.2-2018 spec for 100Base-T1

net: phy: tja11xx: add support for master-slave configuration

The TJA11xx PHYs have a vendor specific Master/Slave configuration bit,
which is not compatible with IEEE 803.2-2018 spec for 100Base-T1
devices. So, provide a custom config_ange call back to solve this
problem.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add delayed registration of TJA1102 PHY1

TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detection by
comp

net: phy: tja11xx: add delayed registration of TJA1102 PHY1

TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detection by
compatible, on other hand we should be able to reset complete chip
before PHY1 configured it, and we need to define dependencies for proper
power management.

We can solve it by defining PHY1 as child of PHY0:
tja1102_phy0: ethernet-phy@4 {
reg = <0x4>;

interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;

reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
reset-assert-us = <20>;
reset-deassert-us = <2000>;

tja1102_phy1: ethernet-phy@5 {
reg = <0x5>;

interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
};
};

The PHY1 should be a subnode of PHY0 and registered only after PHY0 was
completely reset and initialized.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add initial TJA1102 support

TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For
example PHY

net: phy: tja11xx: add initial TJA1102 support

TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For
example PHY 1 has no PHY ID and no health monitor.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: use phy_read_poll_timeout() to simplify the code

use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.

Suggested-by: Andrew Lunn <andrew@lu

net: phy: tja11xx: use phy_read_poll_timeout() to simplify the code

use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: Switch to HWMON_CHANNEL_INFO()

The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.

Signed-off-by: Marek Vasut <

net: phy: tja11xx: Switch to HWMON_CHANNEL_INFO()

The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: Add TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Marek Vasut <marex@de

net: phy: tja11xx: Add TJA11xx PHY driver

Add driver for the NXP TJA1100 and TJA1101 PHYs. These PHYs are special
BroadRReach 100BaseT1 PHYs used in automotive.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethtool: Add generic parts of cable test TDR

Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement

net: ethtool: Add generic parts of cable test TDR

Add the generic parts of the code used to trigger a cable test and
return raw TDR data. Any PHY driver which support this must implement
the new driver op.

Signed-off-by: Andrew Lunn <andrew@lunn.ch>

v2
Update nxp-tja11xx for API change.

Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add SQI support

This patch implements reading of the Signal Quality Index for better
cable/link troubleshooting.

Signed-off-by: Oleksij Rempel <o.rempel@pengu

net: phy: tja11xx: add SQI support

This patch implements reading of the Signal Quality Index for better
cable/link troubleshooting.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: execute cable test on link up

A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be

net: phy: tja11xx: execute cable test on link up

A typical 100Base-T1 link should be always connected. If the link is in
a shot or open state, it is a failure. In most cases, we won't be able
to automatically handle this issue, but we need to log it or notify user
(if possible).

With this patch, the cable will be tested on "ip l s dev .. up" attempt
and send ethnl notification to the user space.

This patch was tested with TJA1102 PHY and "ethtool --monitor" command.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add cable-test support

Add initial cable testing support.
This PHY needs only 100usec for this test and it is recommended to run it
before the link is up. For now,

net: phy: tja11xx: add cable-test support

Add initial cable testing support.
This PHY needs only 100usec for this test and it is recommended to run it
before the link is up. For now, provide at least ethtool support, so it
can be tested by more developers.

This patch was tested with TJA1102 PHY with following results:
- No cable, is detected as open
- 1m cable, with no connected other end and detected as open
- a 40m cable (out of spec, max lenght should be 15m) is detected as OK.

Current patch do not provide polarity test support. This test would
indicate not proper wire connection, where "+" wire of main phy is
connected to the "-" wire of the link partner.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add support for master-slave configuration

The TJA11xx PHYs have a vendor specific Master/Slave configuration bit,
which is not compatible with IEEE 803.2-2018 spec fo

net: phy: tja11xx: add support for master-slave configuration

The TJA11xx PHYs have a vendor specific Master/Slave configuration bit,
which is not compatible with IEEE 803.2-2018 spec for 100Base-T1
devices. So, provide a custom config_ange call back to solve this
problem.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add delayed registration of TJA1102 PHY1

TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detec

net: phy: tja11xx: add delayed registration of TJA1102 PHY1

TJA1102 is a dual PHY package with PHY0 having proper PHYID and PHY1
having no ID. On one hand it is possible to for PHY detection by
compatible, on other hand we should be able to reset complete chip
before PHY1 configured it, and we need to define dependencies for proper
power management.

We can solve it by defining PHY1 as child of PHY0:
tja1102_phy0: ethernet-phy@4 {
reg = <0x4>;

interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;

reset-gpios = <&gpio5 9 GPIO_ACTIVE_LOW>;
reset-assert-us = <20>;
reset-deassert-us = <2000>;

tja1102_phy1: ethernet-phy@5 {
reg = <0x5>;

interrupts-extended = <&gpio5 8 IRQ_TYPE_LEVEL_LOW>;
};
};

The PHY1 should be a subnode of PHY0 and registered only after PHY0 was
completely reset and initialized.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: add initial TJA1102 support

TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For

net: phy: tja11xx: add initial TJA1102 support

TJA1102 is an dual T1 PHY chip. Both PHYs are separately addressable.
Both PHYs are similar but have different amount of functionality. For
example PHY 1 has no PHY ID and no health monitor.

Signed-off-by: Oleksij Rempel <o.rempel@pengutronix.de>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: use phy_read_poll_timeout() to simplify the code

use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.

Suggested-by: An

net: phy: tja11xx: use phy_read_poll_timeout() to simplify the code

use phy_read_poll_timeout() to replace the poll codes for
simplify tja11xx_check() function.

Suggested-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Dejin Zheng <zhengdejin5@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: tja11xx: Switch to HWMON_CHANNEL_INFO()

The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.

Signed-o

net: phy: tja11xx: Switch to HWMON_CHANNEL_INFO()

The HWMON_CHANNEL_INFO macro simplifies the code, reduces the likelihood
of errors, and makes the code easier to read.

Signed-off-by: Marek Vasut <marex@denx.de>
Cc: Andrew Lunn <andrew@lunn.ch>
Cc: Florian Fainelli <f.fainelli@gmail.com>
Cc: Guenter Roeck <linux@roeck-us.net>
Cc: Heiner Kallweit <hkallweit1@gmail.com>
Cc: Jean Delvare <jdelvare@suse.com>
Cc: linux-hwmon@vger.kernel.org
Reviewed-by: Guenter Roeck <linux@roeck-us.net>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...