net: pcs: xpcs: support to switch mode for Wangxun NICs

According to chapter 6 of DesignWare Cores Ethernet PCS (version 3.20a)
and custom design manual, add a configuration flow for switching inter

net: pcs: xpcs: support to switch mode for Wangxun NICs

According to chapter 6 of DesignWare Cores Ethernet PCS (version 3.20a)
and custom design manual, add a configuration flow for switching interface
mode.

If the interface changes, the following setting is required:
1. wait VR_XS_PCS_DIG_STS bit(4, 2) [PSEQ_STATE] = 100b (Power-Good)
2. write SR_XS_PCS_CTRL2 to select various PCS type
3. write SR_PMA_CTRL1 and/or SR_XS_PCS_CTRL1 for link speed
4. program PMA registers
5. write VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] = 1b (Vendor-Specific
Soft Reset)
6. wait for VR_XS_PCS_DIG_CTRL1 bit(15) [VR_RST] to get cleared

Only 10GBASE-R/SGMII/1000BASE-X modes are planned for the current Wangxun
devices. And there is a quirk for Wangxun devices to switch mode although
the interface in phylink state has not changed, since PCS will change to
default 10GBASE-R when the ethernet driver(txgbe) do LAN reset.

Signed-off-by: Jiawen Wu <jiawenwu@trustnetic.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: pcs: Drop the TSE PCS driver

Now that we can easily create a mdio-device that represents a
memory-mapped device that exposes an MDIO-like register layout, we don't
need the Altera TSE PCS anymo

net: pcs: Drop the TSE PCS driver

Now that we can easily create a mdio-device that represents a
memory-mapped device that exposes an MDIO-like register layout, we don't
need the Altera TSE PCS anymore, since we can use the Lynx PCS instead.

Reviewed-by: Simon Horman <simon.horman@corigine.com>
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: pcs: add driver for MediaTek SGMII PCS

The SGMII core found in several MediaTek SoCs is identical to what can
also be found in MediaTek's MT7531 Ethernet switch IC.
As this has not always been

net: pcs: add driver for MediaTek SGMII PCS

The SGMII core found in several MediaTek SoCs is identical to what can
also be found in MediaTek's MT7531 Ethernet switch IC.
As this has not always been clear, both drivers developed different
implementations to deal with the PCS.
Recently Alexander Couzens pointed out this fact which lead to the
development of this shared driver.

Add a dedicated driver, mostly by copying the code now found in the
Ethernet driver. The now redundant code will be removed by a follow-up
commit.

Suggested-by: Alexander Couzens <lynxis@fe80.eu>
Suggested-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Daniel Golle <daniel@makrotopia.org>
Tested-by: Frank Wunderlich <frank-w@public-files.de>
Reviewed-by: Russell King (Oracle) <rmk+kernel@armlinux.org.uk>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: pcs: add new PCS driver for altera TSE PCS

The Altera Triple Speed Ethernet has a SGMII/1000BaseC PCS that can be
integrated in several ways. It can either be part of the TSE MAC's
address spac

net: pcs: add new PCS driver for altera TSE PCS

The Altera Triple Speed Ethernet has a SGMII/1000BaseC PCS that can be
integrated in several ways. It can either be part of the TSE MAC's
address space, accessed through 32 bits accesses on the mapped mdio
device 0, or through a dedicated 16 bits register set.

This driver allows using the TSE PCS outside of altera TSE's driver,
since it can be used standalone by other MACs.

Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: pcs: add Renesas MII converter driver

Add a PCS driver for the MII converter that is present on the Renesas
RZ/N1 SoC. This MII converter is reponsible for converting MII to
RMII/RGMII or act a

net: pcs: add Renesas MII converter driver

Add a PCS driver for the MII converter that is present on the Renesas
RZ/N1 SoC. This MII converter is reponsible for converting MII to
RMII/RGMII or act as a MII pass-trough. Exposing it as a PCS allows to
reuse it in both the switch driver and the stmmac driver. Currently,
this driver only allows the PCS to be used by the dual Cortex-A7
subsystem since the register locking system is not used.

Signed-off-by: Clément Léger <clement.leger@bootlin.com>
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: pcs: xpcs: add support for NXP SJA1105

The NXP SJA1105 DSA switch integrates a Synopsys SGMII XPCS on port 4.
The generic code works fine, except there is an integration issue which
needs to be

net: pcs: xpcs: add support for NXP SJA1105

The NXP SJA1105 DSA switch integrates a Synopsys SGMII XPCS on port 4.
The generic code works fine, except there is an integration issue which
needs to be dealt with: in this switch, the XPCS is integrated with a
PMA that has the TX lane polarity inverted by default (PLUS is MINUS,
MINUS is PLUS).

To obtain normal non-inverted behavior, the TX lane polarity must be
inverted in the PCS, via the DIGITAL_CONTROL_2 register.

We introduce a pma_config() method in xpcs_compat which is called by the
phylink_pcs_config() implementation.

Also, the NXP SJA1105 returns all zeroes in the PHY ID registers 2 and 3.
We need to hack up an ad-hoc PHY ID (OUI is zero, device ID is 1) in
order for the XPCS driver to recognize it. This PHY ID is added to the
public include/linux/pcs/pcs-xpcs.h for that reason (for the sja1105
driver to be able to use it in a later patch).

Signed-off-by: Vladimir Oltean <vladimir.oltean@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: add Lynx PCS module

Add a Lynx PCS module which exposes the necessary operations to drive
the PCS using phylink.

The majority of the code is extracted from the Felix DSA driver, which
wil

net: phy: add Lynx PCS module

Add a Lynx PCS module which exposes the necessary operations to drive
the PCS using phylink.

The majority of the code is extracted from the Felix DSA driver, which
will be also modified in a later patch, and exposed as a separate module
for code reusability purposes.
As such, this aims at feature and bug parity with the existing Felix DSA
driver, and thus USXGMII, SGMII, QSGMII and 2500Base-X (only w/o in-band
AN) are supported by the Lynx PCS module since these were also supported
by Felix.

The module can only be enabled by the drivers in need and not user
selectable.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: pcs: Move XPCS into new PCS subdirectory

Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs

Start a

net: pcs: Move XPCS into new PCS subdirectory

Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs

Start a naming convention of all PCS files use the prefix pcs-, and
rename the XPCS files to fit.

v2:
Add include/linux/pcs

v4:
Fix include path in stmmac.
Remove PCS_DEVICES to avoid new prompts

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: phy: add Lynx PCS module

Add a Lynx PCS module which exposes the necessary operations to drive
the PCS using phylink.

The majority of the code is extracted from the Felix D

net: phy: add Lynx PCS module

Add a Lynx PCS module which exposes the necessary operations to drive
the PCS using phylink.

The majority of the code is extracted from the Felix DSA driver, which
will be also modified in a later patch, and exposed as a separate module
for code reusability purposes.
As such, this aims at feature and bug parity with the existing Felix DSA
driver, and thus USXGMII, SGMII, QSGMII and 2500Base-X (only w/o in-band
AN) are supported by the Lynx PCS module since these were also supported
by Felix.

The module can only be enabled by the drivers in need and not user
selectable.

Signed-off-by: Ioana Ciornei <ioana.ciornei@nxp.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: pcs: Move XPCS into new PCS subdirectory

Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/li

net: pcs: Move XPCS into new PCS subdirectory

Create drivers/net/pcs and move the Synopsys DesignWare XPCS into the
new directory. Move the header file into a subdirectory
include/linux/pcs

Start a naming convention of all PCS files use the prefix pcs-, and
rename the XPCS files to fit.

v2:
Add include/linux/pcs

v4:
Fix include path in stmmac.
Remove PCS_DEVICES to avoid new prompts

Cc: Jose Abreu <Jose.Abreu@synopsys.com>
Reviewed-by: Florian Fainelli <f.fainelli@gmail.com>
Signed-off-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...