net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Gen

net: ethernet: move from strlcpy with unused retval to strscpy

Follow the advice of the below link and prefer 'strscpy' in this
subsystem. Conversion is 1:1 because the return value is not used.
Generated by a coccinelle script.

Link: https://lore.kernel.org/r/CAHk-=wgfRnXz0W3D37d01q3JFkr_i_uTL=V6A6G1oUZcprmknw@mail.gmail.com/
Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # For drivers/net/ethernet/mellanox/mlxsw
Acked-by: Geoff Levand <geoff@infradead.org> # For ps3_gelic_net and spider_net_ethtool
Acked-by: Tom Lendacky <thomas.lendacky@amd.com> # For drivers/net/ethernet/amd/xgbe/xgbe-ethtool.c
Acked-by: Marcin Wojtas <mw@semihalf.com> # For drivers/net/ethernet/marvell/mvpp2
Reviewed-by: Leon Romanovsky <leonro@nvidia.com> # For drivers/net/ethernet/mellanox/mlx{4|5}
Reviewed-by: Shay Agroskin <shayagr@amazon.com> # For drivers/net/ethernet/amazon/ena
Acked-by: Krzysztof Hałasa <khalasa@piap.pl> # For IXP4xx Ethernet
Link: https://lore.kernel.org/r/20220830201457.7984-3-wsa+renesas@sang-engineering.com
Signed-off-by: Jakub Kicinski <kuba@kernel.org>

show more ...

net: ethernet: ti: am65-cpsw-ethtool: use pm_runtime_resume_and_get

Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the co

net: ethernet: ti: am65-cpsw-ethtool: use pm_runtime_resume_and_get

Using pm_runtime_resume_and_get() to replace pm_runtime_get_sync and
pm_runtime_put_noidle. This change is just to simplify the code, no
actual functional changes.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: Minghao Chi <chi.minghao@zte.com.cn>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw: Convert to PHYLINK

Convert am65-cpsw driver and am65-cpsw ethtool to use Phylink APIs
as described at Documentation/networking/sfp-phylink.rst. All calls
to Phy APIs ar

net: ethernet: ti: am65-cpsw: Convert to PHYLINK

Convert am65-cpsw driver and am65-cpsw ethtool to use Phylink APIs
as described at Documentation/networking/sfp-phylink.rst. All calls
to Phy APIs are replaced with their equivalent Phylink APIs.

No functional change intended. Use Phylink instead of conventional
Phylib, in preparation to add support for SGMII/QSGMII modes.

Signed-off-by: Siddharth Vadapalli <s-vadapalli@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ethtool: extend ringparam setting/getting API with rx_buf_len

Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.

Si

ethtool: extend ringparam setting/getting API with rx_buf_len

Add two new parameters kernel_ringparam and extack for
.get_ringparam and .set_ringparam to extend more ring params
through netlink.

Signed-off-by: Hao Chen <chenhao288@hisilicon.com>
Signed-off-by: Guangbin Huang <huangguangbin2@huawei.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

am65-cpsw: avoid null pointer arithmetic

clang warns about arithmetic on NULL pointers:

drivers/net/ethernet/ti/am65-cpsw-ethtool.c:71:2: error: performing pointer subtraction with a null pointer h

am65-cpsw: avoid null pointer arithmetic

clang warns about arithmetic on NULL pointers:

drivers/net/ethernet/ti/am65-cpsw-ethtool.c:71:2: error: performing pointer subtraction with a null pointer has undefined behavior [-Werror,-Wnull-pointer-subtraction]
AM65_CPSW_REGDUMP_REC(AM65_CPSW_REGDUMP_MOD_NUSS, 0x0, 0x1c),
^~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~~
drivers/net/ethernet/ti/am65-cpsw-ethtool.c:64:29: note: expanded from macro 'AM65_CPSW_REGDUMP_REC'
.hdr.len = (((u32 *)(end)) - ((u32 *)(start)) + 1) * sizeof(u32) * 2 + \
^ ~~~~~~~~~~~~~~~~

The expression here is easily changed to a calculation based on integers
that is no less readable.

Signed-off-by: Arnd Bergmann <arnd@arndb.de>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: ale: add cpsw_ale_get_num_entries api

Add cpsw_ale_get_num_entries() API to return number of ALE table entries
and update existing drivers to use it.

Signed-off-by: Grygorii Stra

net: ethernet: ti: ale: add cpsw_ale_get_num_entries api

Add cpsw_ale_get_num_entries() API to return number of ALE table entries
and update existing drivers to use it.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw-ethtool: configured critical setting only when no running netdevs

Ensure that critical setting can only be configured when there are no
running netdevs - all ports are d

net: ethernet: ti: am65-cpsw-ethtool: configured critical setting only when no running netdevs

Ensure that critical setting can only be configured when there are no
running netdevs - all ports are down.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw-ethtool: skip hw cfg when change p0-rx-ptype-rrobin

Skip HW configuration when p0-rx-ptype-rrobin is changed as it will be done
by .ndev_open(),

Signed-off-by: Grygorii

net: ethernet: ti: am65-cpsw-ethtool: skip hw cfg when change p0-rx-ptype-rrobin

Skip HW configuration when p0-rx-ptype-rrobin is changed as it will be done
by .ndev_open(),

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ethernet: ti: am65-cpsw-qos: add TAPRIO offload support

AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration.

ethernet: ti: am65-cpsw-qos: add TAPRIO offload support

AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() to offload EST configuration to CPSW h/w.

Currently driver supports only SetGateStates operation. EST
operates on a repeating time interval generated by the CPTS EST
function generator. Each Ethernet port has a global EST fetch
RAM that can be configured as 2 buffers, each of 64 locations
or one large buffer of 128 locations. In 2 buffer configuration,
a ping pong mechanism is used to hold the active schedule (oper)
in one buffer and new (admin) command in the other. Each 22-bit
fetch command consists of a 14-bit fetch count (14 MSB’s) and an
8-bit priority fetch allow (8 LSB’s) that will be applied for the
fetch count time in wireside clocks. Driver process each of the
sched-entry in the offload command and update the fetch RAM.
Driver configures duration in sched-entry into the fetch count
and Gate mask into the priority fetch bits of the RAM. Then
configures the CPTS EST function generator to activate the
schedule. Currently driver supports only 2 buffer configuration
which means driver supports a max cycle time of ~8 msec.

CPSW supports a configurable number of priority queues (up to 8)
and needs to be switched to this mode from the default round
robin mode before EST can be offloaded. User configures
these through ethtool commands (-L for changing number of
queues and --set-priv-flags to disable round robin mode).
Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag
is set. The flag is common for all ports, and so can't be just
overridden by taprio configuration w/o user involvement.
Command fails if pf_p0_rx_ptype_rrobin is already set in the
driver.

Scheds (commands) configuration depends on interface speed so
driver translates the duration to the fetch count based on
link speed. Each schedule can be constructed with several
command entries in fetch RAM depending on interval. For example
if each sched has timer interval < ~130us on 1000 Mb link then
each sched consumes one command and have 1:1 mapping. When
Ethernet link goes down, driver purge the configuration if link
is down for more than 1 second.

The patch allows to update the timer and scheds memory only if it's
really needed, and skip cases required the user to stop timer by
configuring only shceds memory.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support

The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.

This enables

net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support

The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.

This enables corresponding support in TI AM65x/J721E MCU CPSW driver.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectab

net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectable RGMII and RMII
interfaces and an internal Communications Port Programming Interface (CPPI)
port (Host port 0) and with ALE in between. It also contains
- Management Data Input/Output (MDIO) interface for physical layer device
(PHY) management;
- Updated Address Lookup Engine (ALE) module;
- (TBD) New version of Common platform time sync (CPTS) module.

On the TI am65x/J721E SoCs CPSW NUSS Ethernet subsystem into device MCU
domain named MCU_CPSW0.

Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and one RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.

Introduced driver provides standard Linux net_device to user space and supports:
- ifconfig up/down
- MAC address configuration
- ethtool operation:
--driver
--change
--register-dump
--negotiate phy
--statistics
--set-eee phy
--show-ring
--show-channels
--set-channels
- net_device ioctl mii-control
- promisc mode

- rx checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets.
The CPSW NUSS can verify IPv4/IPv6 TCP/UDP packets checksum and fills
csum information for each packet in psdata[2] word:
- BIT(16) CHECKSUM_ERROR - indicates csum error
- BIT(17) FRAGMENT - indicates fragmented packet
- BIT(18) TCP_UDP_N - Indicates TCP packet was detected
- BIT(19) IPV6_VALID, BIT(20) IPV4_VALID - indicates IPv6/IPv4 packet
- BIT(15, 0) CHECKSUM_ADD - This is the value that was summed
during the checksum computation. This value is FFFFh for non fragmented
IPV4/6 UDP/TCP packets with no checksum error.

RX csum offload can be disabled:
ethtool -K <dev> rx-checksum on|off

- tx checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).
TX csum HW offload can be enabled/disabled:
ethtool -K <dev> tx-checksum-ip-generic on|off

- multiq and switch between round robin/prio modes for cppi tx queues by
using Netdev private flag "p0-rx-ptype-rrobin" to switch between
Round Robin and Fixed priority modes:
# ethtool --show-priv-flags eth0
Private flags for eth0:
p0-rx-ptype-rrobin: on
# ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off

Number of TX DMA channels can be changed using "ethtool -L eth0 tx <N>".

- GRO support: the napi_gro_receive() and napi_complete_done() are used.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: ale: add cpsw_ale_get_num_entries api

Add cpsw_ale_get_num_entries() API to return number of ALE table entries
and update existing drivers to use it.

Signed-o

net: ethernet: ti: ale: add cpsw_ale_get_num_entries api

Add cpsw_ale_get_num_entries() API to return number of ALE table entries
and update existing drivers to use it.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw-ethtool: configured critical setting only when no running netdevs

Ensure that critical setting can only be configured when there are no
running netdevs - all

net: ethernet: ti: am65-cpsw-ethtool: configured critical setting only when no running netdevs

Ensure that critical setting can only be configured when there are no
running netdevs - all ports are down.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw-ethtool: skip hw cfg when change p0-rx-ptype-rrobin

Skip HW configuration when p0-rx-ptype-rrobin is changed as it will be done
by .ndev_open(),

Sig

net: ethernet: ti: am65-cpsw-ethtool: skip hw cfg when change p0-rx-ptype-rrobin

Skip HW configuration when p0-rx-ptype-rrobin is changed as it will be done
by .ndev_open(),

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

ethernet: ti: am65-cpsw-qos: add TAPRIO offload support

AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)

ethernet: ti: am65-cpsw-qos: add TAPRIO offload support

AM65 CPSW h/w supports Enhanced Scheduled Traffic (EST – defined
in P802.1Qbv/D2.2 that later got included in IEEE 802.1Q-2018)
configuration. EST allows express queue traffic to be scheduled
(placed) on the wire at specific repeatable time intervals. In
Linux kernel, EST configuration is done through tc command and
the taprio scheduler in the net core implements a software only
scheduler (SCH_TAPRIO). If the NIC is capable of EST configuration,
user indicate "flag 2" in the command which is then parsed by
taprio scheduler in net core and indicate that the command is to
be offloaded to h/w. taprio then offloads the command to the
driver by calling ndo_setup_tc() ndo ops. This patch implements
ndo_setup_tc() to offload EST configuration to CPSW h/w.

Currently driver supports only SetGateStates operation. EST
operates on a repeating time interval generated by the CPTS EST
function generator. Each Ethernet port has a global EST fetch
RAM that can be configured as 2 buffers, each of 64 locations
or one large buffer of 128 locations. In 2 buffer configuration,
a ping pong mechanism is used to hold the active schedule (oper)
in one buffer and new (admin) command in the other. Each 22-bit
fetch command consists of a 14-bit fetch count (14 MSB’s) and an
8-bit priority fetch allow (8 LSB’s) that will be applied for the
fetch count time in wireside clocks. Driver process each of the
sched-entry in the offload command and update the fetch RAM.
Driver configures duration in sched-entry into the fetch count
and Gate mask into the priority fetch bits of the RAM. Then
configures the CPTS EST function generator to activate the
schedule. Currently driver supports only 2 buffer configuration
which means driver supports a max cycle time of ~8 msec.

CPSW supports a configurable number of priority queues (up to 8)
and needs to be switched to this mode from the default round
robin mode before EST can be offloaded. User configures
these through ethtool commands (-L for changing number of
queues and --set-priv-flags to disable round robin mode).
Driver doesn't enable EST if pf_p0_rx_ptype_rrobin privat flag
is set. The flag is common for all ports, and so can't be just
overridden by taprio configuration w/o user involvement.
Command fails if pf_p0_rx_ptype_rrobin is already set in the
driver.

Scheds (commands) configuration depends on interface speed so
driver translates the duration to the fetch count based on
link speed. Each schedule can be constructed with several
command entries in fetch RAM depending on interval. For example
if each sched has timer interval < ~130us on 1000 Mb link then
each sched consumes one command and have 1:1 mapping. When
Ethernet link goes down, driver purge the configuration if link
is down for more than 1 second.

The patch allows to update the timer and scheds memory only if it's
really needed, and skip cases required the user to stop timer by
configuring only shceds memory.

Signed-off-by: Ivan Khoronzhuk <ivan.khoronzhuk@linaro.org>
Signed-off-by: Murali Karicheri <m-karicheri2@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support

The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.

net: ethernet: ti: am65-cpsw-nuss: enable packet timestamping support

The MCU CPSW Common Platform Time Sync (CPTS) provides possibility to
timestamp TX PTP packets and all RX packets.

This enables corresponding support in TI AM65x/J721E MCU CPSW driver.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) w

net: ethernet: ti: introduce am65x/j721e gigabit eth subsystem driver

The TI AM65x/J721E SoCs Gigabit Ethernet Switch subsystem (CPSW2G NUSS) has
two ports - One Ethernet port (port 1) with selectable RGMII and RMII
interfaces and an internal Communications Port Programming Interface (CPPI)
port (Host port 0) and with ALE in between. It also contains
- Management Data Input/Output (MDIO) interface for physical layer device
(PHY) management;
- Updated Address Lookup Engine (ALE) module;
- (TBD) New version of Common platform time sync (CPTS) module.

On the TI am65x/J721E SoCs CPSW NUSS Ethernet subsystem into device MCU
domain named MCU_CPSW0.

Host Port 0 CPPI Packet Streaming Interface interface supports 8 TX
channels and one RX channels operating by TI am654 NAVSS Unified DMA
Peripheral Root Complex (UDMA-P) controller.

Introduced driver provides standard Linux net_device to user space and supports:
- ifconfig up/down
- MAC address configuration
- ethtool operation:
--driver
--change
--register-dump
--negotiate phy
--statistics
--set-eee phy
--show-ring
--show-channels
--set-channels
- net_device ioctl mii-control
- promisc mode

- rx checksum offload for non-fragmented IPv4/IPv6 TCP/UDP packets.
The CPSW NUSS can verify IPv4/IPv6 TCP/UDP packets checksum and fills
csum information for each packet in psdata[2] word:
- BIT(16) CHECKSUM_ERROR - indicates csum error
- BIT(17) FRAGMENT - indicates fragmented packet
- BIT(18) TCP_UDP_N - Indicates TCP packet was detected
- BIT(19) IPV6_VALID, BIT(20) IPV4_VALID - indicates IPv6/IPv4 packet
- BIT(15, 0) CHECKSUM_ADD - This is the value that was summed
during the checksum computation. This value is FFFFh for non fragmented
IPV4/6 UDP/TCP packets with no checksum error.

RX csum offload can be disabled:
ethtool -K <dev> rx-checksum on|off

- tx checksum offload support for IPv4/IPv6 TCP/UDP packets (J721E only).
TX csum HW offload can be enabled/disabled:
ethtool -K <dev> tx-checksum-ip-generic on|off

- multiq and switch between round robin/prio modes for cppi tx queues by
using Netdev private flag "p0-rx-ptype-rrobin" to switch between
Round Robin and Fixed priority modes:
# ethtool --show-priv-flags eth0
Private flags for eth0:
p0-rx-ptype-rrobin: on
# ethtool --set-priv-flags eth0 p0-rx-ptype-rrobin off

Number of TX DMA channels can be changed using "ethtool -L eth0 tx <N>".

- GRO support: the napi_gro_receive() and napi_complete_done() are used.

Signed-off-by: Grygorii Strashko <grygorii.strashko@ti.com>
Tested-by: Murali Karicheri <m-karicheri2@ti.com>
Tested-by: Peter Ujfalusi <peter.ujfalusi@ti.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...