|
Revision tags: v6.6.25, v6.6.24, v6.6.23, v6.6.16, v6.6.15, v6.6.14 |
|
| #
f0025c92 |
| 24-Jan-2024 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Fix port configuration when using SGMII interface
[ Upstream commit 62b4248105353e7d1debd30ca5c57ec5e5f28e35 ]
In case the interface between the MAC and the PHY is SGMII, then the bit
net: lan966x: Fix port configuration when using SGMII interface
[ Upstream commit 62b4248105353e7d1debd30ca5c57ec5e5f28e35 ]
In case the interface between the MAC and the PHY is SGMII, then the bit
GIGA_MODE on the MAC side needs to be set regardless of the speed at
which it is running.
Fixes: d28d6d2e37d1 ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
|
Revision tags: v6.6.13, v6.6.12, v6.6.11, v6.6.10, v6.6.9, v6.6.8, v6.6.7, v6.6.6, v6.6.5, v6.6.4, v6.6.3, v6.6.2, v6.5.11, v6.6.1, v6.5.10, v6.6, v6.5.9, v6.5.8, v6.5.7, v6.5.6, v6.5.5, v6.5.4, v6.5.3, v6.5.2, v6.1.51, v6.5.1, v6.1.50, v6.5, v6.1.49, v6.1.48, v6.1.46, v6.1.45, v6.1.44, v6.1.43, v6.1.42, v6.1.41, v6.1.40, v6.1.39, v6.1.38, v6.1.37, v6.1.36, v6.4, v6.1.35, v6.1.34, v6.1.33, v6.1.32, v6.1.31, v6.1.30, v6.1.29 |
|
| #
d38ddd56 |
| 16-May-2023 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Add support for DSCP rewrite
Add support for DSCP rewrite in lan966x driver. On egress DSCP is
rewritten from either classified DSCP, or frame DSCP. Classified DSCP is
determined by th
net: lan966x: Add support for DSCP rewrite
Add support for DSCP rewrite in lan966x driver. On egress DSCP is
rewritten from either classified DSCP, or frame DSCP. Classified DSCP is
determined by the Analyzer Classifier on ingress, and is mapped from
classified QoS class and DP level. Classification of DSCP is by default
enabled for all ports.
It is required that DSCP is trusted for the egress port *and* rewrite
table is not empty, in order to rewrite DSCP based on classified DSCP,
otherwise DSCP is always rewritten from frame DSCP.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
show more ...
|
| #
363f98b9 |
| 16-May-2023 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Add support for PCP rewrite
Add support for rewrite of PCP and DEI value, based on QoS and DP level.
The DCB rewrite table is queried for mappings between priority and
PCP/DEI. The cl
net: lan966x: Add support for PCP rewrite
Add support for rewrite of PCP and DEI value, based on QoS and DP level.
The DCB rewrite table is queried for mappings between priority and
PCP/DEI. The classified DP level is then encoded in the DEI bit, if a
mapping for DEI exists.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
show more ...
|
| #
f8ba50ea |
| 16-May-2023 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Add support for offloading default prio
Add support for offloading default prio.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski
net: lan966x: Add support for offloading default prio
Add support for offloading default prio.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
show more ...
|
| #
0c88d981 |
| 16-May-2023 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Add support for offloading dscp table
Add support for offloading dscp app entries. The dscp values are global
for all lan966x ports.
Reviewed-by: Daniel Machon <daniel.machon@microchi
net: lan966x: Add support for offloading dscp table
Add support for offloading dscp app entries. The dscp values are global
for all lan966x ports.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
show more ...
|
| #
a83e4630 |
| 16-May-2023 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Add support for offloading pcp table
Add support for offloading pcp app entries. Lan966x has 8 priority
queues per port and for each priority it also has a drop precedence.
Reviewed-b
net: lan966x: Add support for offloading pcp table
Add support for offloading pcp app entries. Lan966x has 8 priority
queues per port and for each priority it also has a drop precedence.
Reviewed-by: Daniel Machon <daniel.machon@microchip.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
show more ...
|
|
Revision tags: v6.1.28, v6.1.27, v6.1.26, v6.3, v6.1.25, v6.1.24, v6.1.23, v6.1.22, v6.1.21, v6.1.20, v6.1.19, v6.1.18, v6.1.17, v6.1.16, v6.1.15, v6.1.14, v6.1.13, v6.2, v6.1.12, v6.1.11, v6.1.10, v6.1.9, v6.1.8, v6.1.7, v6.1.6, v6.1.5, v6.0.19, v6.0.18, v6.1.4, v6.1.3, v6.0.17, v6.1.2, v6.0.16, v6.1.1, v6.0.15 |
|
| #
d717f947 |
| 21-Dec-2022 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Fix configuration of the PCS
When the PCS was taken out of reset, we were changing by mistake also
the speed to 100 Mbit. But in case the link was going down, the link
up routine was s
net: lan966x: Fix configuration of the PCS
When the PCS was taken out of reset, we were changing by mistake also
the speed to 100 Mbit. But in case the link was going down, the link
up routine was setting correctly the link speed. If the link was not
getting down then the speed was forced to run at 100 even if the
speed was something else.
On lan966x, to set the speed link to 1G or 2.5G a value of 1 needs to be
written in DEV_CLOCK_CFG_LINK_SPEED. This is similar to the procedure in
lan966x_port_init.
The issue was reproduced using 1000base-x sfp module using the commands:
ip link set dev eth2 up
ip link addr add 10.97.10.2/24 dev eth2
ethtool -s eth2 speed 1000 autoneg off
Fixes: d28d6d2e37d1 ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Reviewed-by: Piotr Raczynski <piotr.raczynski@intel.com>
Link: https://lore.kernel.org/r/20221221093315.939133-1-horatiu.vultur@microchip.com
Signed-off-by: Paolo Abeni <pabeni@redhat.com>
show more ...
|
|
Revision tags: v6.0.14, v6.0.13, v6.1, v6.0.12, v6.0.11, v6.0.10, v5.15.80, v6.0.9, v5.15.79, v6.0.8, v5.15.78, v6.0.7, v5.15.77, v5.15.76, v6.0.6, v6.0.5, v5.15.75, v6.0.4, v6.0.3, v6.0.2, v5.15.74, v5.15.73, v6.0.1, v5.15.72, v6.0, v5.15.71, v5.15.70 |
|
| #
e462b271 |
| 21-Sep-2022 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Add offload support for taprio
Lan966x switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. Add support for TAS configuration on
egress port of lan966x swi
net: lan966x: Add offload support for taprio
Lan966x switch supports time-based egress shaping in hardware
according to IEEE 802.1Qbv. Add support for TAS configuration on
egress port of lan966x switch.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
show more ...
|
|
Revision tags: v5.15.69, v5.15.68, v5.15.67, v5.15.66, v5.15.65, v5.15.64, v5.15.63, v5.15.62 |
|
| #
ac0167fb |
| 17-Aug-2022 |
Maxime Chevallier <maxime.chevallier@bootlin.com> |
net: lan966x: Add QUSGMII support for lan966x
The Lan996x controller supports the QUSGMII mode, which is very similar
to QSGMII in the way it's configured and the autonegociation
capababilities it p
net: lan966x: Add QUSGMII support for lan966x
The Lan996x controller supports the QUSGMII mode, which is very similar
to QSGMII in the way it's configured and the autonegociation
capababilities it provides.
This commit adds support for that mode, treating it most of the time
like QSGMII, making sure that we do configure the PCS how we should.
Signed-off-by: Maxime Chevallier <maxime.chevallier@bootlin.com>
Reviewed-by: Andrew Lunn <andrew@lunn.ch>
Signed-off-by: David S. Miller <davem@davemloft.net>
show more ...
|
|
Revision tags: v5.15.61, v5.15.60, v5.15.59, v5.19, v5.15.58, v5.15.57, v5.15.56, v5.15.55, v5.15.54, v5.15.53, v5.15.52, v5.15.51, v5.15.50, v5.15.49, v5.15.48, v5.15.47, v5.15.46, v5.15.45, v5.15.44, v5.15.43, v5.15.42, v5.18, v5.15.41, v5.15.40, v5.15.39, v5.15.38, v5.15.37, v5.15.36, v5.15.35, v5.15.34, v5.15.33 |
|
| #
c8349639 |
| 08-Apr-2022 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Add FDMA functionality
Ethernet frames can be extracted or injected to or from the device's
DDR memory. There is one channel for injection and one channel for
extraction. Each of these
net: lan966x: Add FDMA functionality
Ethernet frames can be extracted or injected to or from the device's
DDR memory. There is one channel for injection and one channel for
extraction. Each of these channels contain a linked list of DCBs which
contains DB. The DCB contains only 1 DB for both the injection and
extraction. Each DB contains a frame. Every time when a frame is received
or transmitted an interrupt is generated.
It is not possible to use both the FDMA and the manual
injection/extraction of the frames. Therefore the FDMA has priority over
the manual because of better performance values.
FDMA:
iperf -c 192.168.1.1
[ 5] 0.00-10.02 sec 420 MBytes 352 Mbits/sec 0 sender
[ 5] 0.00-10.03 sec 420 MBytes 351 Mbits/sec receiver
iperf -c 192.168.1.1 -R
[ 5] 0.00-10.01 sec 528 MBytes 442 Mbits/sec 0 sender
[ 5] 0.00-10.00 sec 524 MBytes 440 Mbits/sec receiver
Manual:
iperf -c 192.168.1.1
[ 5] 0.00-10.02 sec 93.8 MBytes 78.5 Mbits/sec 0 sender
[ 5] 0.00-10.03 sec 93.8 MBytes 78.4 Mbits/sec receiver
ipers -c 192.168.1.1 -R
[ 5] 0.00-10.03 sec 121 MBytes 101 Mbits/sec 0 sender
[ 5] 0.00-10.01 sec 118 MBytes 99.0 Mbits/sec receiver
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: Jakub Kicinski <kuba@kernel.org>
show more ...
|
|
Revision tags: v5.15.32, v5.15.31, v5.17, v5.15.30, v5.15.29, v5.15.28, v5.15.27, v5.15.26, v5.15.25, v5.15.24, v5.15.23, v5.15.22, v5.15.21, v5.15.20, v5.15.19, v5.15.18, v5.15.17, v5.4.173, v5.15.16, v5.15.15, v5.16, v5.15.10, v5.15.9, v5.15.8 |
|
| #
b26980ab |
| 11-Dec-2021 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: Fix the configuration of the pcs
When inserting a SFP that runs at 2.5G, then the Serdes was still
configured to run at 1G. Because the config->speed was 0, and then the
speed of the s
net: lan966x: Fix the configuration of the pcs
When inserting a SFP that runs at 2.5G, then the Serdes was still
configured to run at 1G. Because the config->speed was 0, and then the
speed of the serdes was not configured at all, it was using the default
value which is 1G. This patch stop calling the serdes function set_speed
and allow the serdes to figure out the speed based on the interface
type.
Fixes: d28d6d2e37d10d ("net: lan966x: add port module support")
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
show more ...
|
|
Revision tags: v5.15.7, v5.15.6 |
|
| #
d28d6d2e |
| 29-Nov-2021 |
Horatiu Vultur <horatiu.vultur@microchip.com> |
net: lan966x: add port module support
This patch adds support for netdev and phylink in the switch. The
injection + extraction is register based. This will be replaced with DMA
accees.
Signed-off-b
net: lan966x: add port module support
This patch adds support for netdev and phylink in the switch. The
injection + extraction is register based. This will be replaced with DMA
accees.
Signed-off-by: Horatiu Vultur <horatiu.vultur@microchip.com>
Signed-off-by: David S. Miller <davem@davemloft.net>
show more ...
|