e1000e: correct maximum frequency adjustment values

[ Upstream commit f1f6a6b1830a8f1dc92ee26fae76333f446b0663 ]

The e1000e driver supports hardware with a variety of different clock
speeds, and th

e1000e: correct maximum frequency adjustment values

[ Upstream commit f1f6a6b1830a8f1dc92ee26fae76333f446b0663 ]

The e1000e driver supports hardware with a variety of different clock
speeds, and thus a variety of different increment values used for
programming its PTP hardware clock.

The values currently programmed in e1000e_ptp_init are incorrect. In
particular, only two maximum adjustments are used: 24000000 - 1, and
600000000 - 1. These were originally intended to be used with the 96 MHz
clock and the 25 MHz clock.

Both of these values are actually slightly too high. For the 96 MHz clock,
the actual maximum value that can safely be programmed is 23,999,938. For
the 25 MHz clock, the maximum value is 599,999,904.

Worse, several devices use a 24 MHz clock or a 38.4 MHz clock. These parts
are incorrectly assigned one of either the 24million or 600million values.
For the 24 MHz clock, this is not a significant issue: its current
increment value can support an adjustment up to 7billion in the positive
direction. However, the 38.4 KHz clock uses an increment value which can
only support up to 230,769,157 before it starts overflowing.

To understand where these values come from, consider that frequency
adjustments have the form of:

new_incval = base_incval + (base_incval * adjustment) / (unit of adjustment)

The maximum adjustment is reported in terms of parts per billion:
new_incval = base_incval + (base_incval * adjustment) / 1 billion

The largest possible adjustment is thus given by the following:
max_incval = base_incval + (base_incval * max_adj) / 1 billion

Re-arranging to solve for max_adj:
max_adj = (max_incval - base_incval) * 1 billion / base_incval

We also need to ensure that negative adjustments cannot underflow. This can
be achieved simply by ensuring max_adj is always less than 1 billion.

Introduce new macros in e1000.h codifying the maximum adjustment in PPB for
each frequency given its associated increment values. Also clarify where
these values come from by commenting about the above equations.

Replace the switch statement in e1000e_ptp_init with one which mirrors the
increment value switch statement from e1000e_get_base_timinica. For each
device, assign the appropriate maximum adjustment based on its frequency.
Some parts can have one of two frequency modes as determined by
E1000_TSYNCRXCTL_SYSCFI.

Since the new flow directly matches the assignments in
e1000e_get_base_timinca, and uses well defined macro names, it is much
easier to verify that the resulting maximum adjustments are correct. It
also avoids difficult to parse construction such as the "hw->mac.type <
e1000_phc_lpt", and the use of fallthrough which was especially confusing
when combined with a conditional block.

Note that I believe the current increment value configuration used for
24MHz clocks is sub-par, as it leaves at least 3 extra bits available in
the INCVALUE register. However, fixing that requires more careful review of
the clock rate and associated values.

Reported-by: Trey Harrison <harrisondigitalmedia@gmail.com>
Fixes: 68fe1d5da548 ("e1000e: Add Support for 38.4MHZ frequency")
Fixes: d89777bf0e42 ("e1000e: add support for IEEE-1588 PTP")
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

e1000e: Separate MTP board type from ADP

We have the same LAN controller on different PCH's. Separate MTP board
type from an ADP which will allow for specific fixes to be applied for MTP
platforms.

e1000e: Separate MTP board type from ADP

We have the same LAN controller on different PCH's. Separate MTP board
type from an ADP which will allow for specific fixes to be applied for MTP
platforms.

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

e1000e: convert .adjfreq to .adjfine

The PTP implementation for the e1000e driver uses the older .adjfreq
method. This method takes an adjustment in parts per billion. The newer
.adjfine implementat

e1000e: convert .adjfreq to .adjfine

The PTP implementation for the e1000e driver uses the older .adjfreq
method. This method takes an adjustment in parts per billion. The newer
.adjfine implementation uses scaled_ppm. The use of scaled_ppm allows for
finer grained adjustments and is preferred over using the older
implementation.

Make use of mul_u64_u64_div_u64 in order to handle possible overflow of the
multiplication used to calculate the desired adjustment to the hardware
increment value.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Naama Meir <naamax.meir@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

e1000e: Separate ADP board type from TGP

We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will allow for specific fixes to be applied for
ADP platforms.

e1000e: Separate ADP board type from TGP

We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will allow for specific fixes to be applied for
ADP platforms.

Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

net: e1000e: solve insmod 'Unknown symbol mutex_lock' error

After I turn on the CONFIG_LOCK_STAT=y, insmod e1000e.ko will report:
[ 5.641579] e1000e: Unknown symbol mutex_lock (err -2)
[ 90.775

net: e1000e: solve insmod 'Unknown symbol mutex_lock' error

After I turn on the CONFIG_LOCK_STAT=y, insmod e1000e.ko will report:
[ 5.641579] e1000e: Unknown symbol mutex_lock (err -2)
[ 90.775705] e1000e: Unknown symbol mutex_lock (err -2)
[ 132.252339] e1000e: Unknown symbol mutex_lock (err -2)

This problem fixed after include <linux/mutex.h>.

Signed-off-by: Hao Chen <chenhaoa@uniontech.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

e1000e: Separate ADP board type from TGP

commit 68defd528f94ed1cf11f49a75cc1875dccd781fa upstream.

We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will

e1000e: Separate ADP board type from TGP

commit 68defd528f94ed1cf11f49a75cc1875dccd781fa upstream.

We have the same LAN controller on different PCH's. Separate ADP board
type from a TGP which will allow for specific fixes to be applied for
ADP platforms.

Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Suggested-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

e1000e: Separate TGP board type from SPT

We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.

Sug

e1000e: Separate TGP board type from SPT

We have the same LAN controller on different PCHs. Separate TGP board
type from SPT which will allow for specific fixes to be applied for
TGP platforms.

Suggested-by: Kai-Heng Feng <kai.heng.feng@canonical.com>
Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Paul Menzel <pmenzel@molgen.mpg.de>
Tested-by: Mark Pearson <markpearson@lenovo.com>
Tested-by: Nechama Kraus <nechamax.kraus@linux.intel.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

e1000e: Export S0ix flags to ethtool

This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.

If you need this flag to be persisted across

e1000e: Export S0ix flags to ethtool

This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.

If you need this flag to be persisted across reboots, it's suggested
to use a udev rule to call adjust it until the kernel could have your
configuration in a disallow list.

Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>

show more ...

e1000e: Export S0ix flags to ethtool

[ Upstream commit 3c98cbf22a96c1b12f48c1b2a4680dfe5cb280f9 ]

This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for devel

e1000e: Export S0ix flags to ethtool

[ Upstream commit 3c98cbf22a96c1b12f48c1b2a4680dfe5cb280f9 ]

This flag can be used by an end user to disable S0ix flows on a
buggy system or by an OEM for development purposes.

If you need this flag to be persisted across reboots, it's suggested
to use a udev rule to call adjust it until the kernel could have your
configuration in a disallow list.

Signed-off-by: Mario Limonciello <mario.limonciello@dell.com>
Reviewed-by: Hans de Goede <hdegoede@redhat.com>
Tested-by: Yijun Shen <Yijun.shen@dell.com>
Signed-off-by: Tony Nguyen <anthony.l.nguyen@intel.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

net/intel: remove driver versions from Intel drivers

As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version

net/intel: remove driver versions from Intel drivers

As with other networking drivers, remove the unnecessary driver version
from the Intel drivers. The ethtool driver information and module version
will then report the kernel version instead.

For ixgbe, i40e and ice drivers, the driver passes the driver version to
the firmware to confirm that we are up and running. So we now pass the
value of UTS_RELEASE to the firmware. This adminq call is required per
the HAS document. The Device then sends an indication to the BMC that the
PF driver is present. This is done using Host NC Driver Status Indication
in NC-SI Get Link command or via the Host Network Controller Driver Status
Change AEN.

What the BMC may do with this information is implementation-dependent, but
this is a standard NC-SI 1.1 command we honor per the HAS.

CC: Bruce Allan <bruce.w.allan@intel.com>
CC: Jesse Brandeburg <jesse.brandeburg@intel.com>
CC: Alek Loktionov <aleksandr.loktionov@intel.com>
CC: Kevin Liedtke <kevin.d.liedtke@intel.com>
CC: Aaron Rowden <aaron.f.rowden@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Co-developed-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>

show more ...

e1000e: Relax condition to trigger reset for ME workaround

It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duratio

e1000e: Relax condition to trigger reset for ME workaround

It's an error if the value of the RX/TX tail descriptor does not match
what was written. The error condition is true regardless the duration
of the interference from ME. But the driver only performs the reset if
E1000_ICH_FWSM_PCIM2PCI_COUNT (2000) iterations of 50us delay have
transpired. The extra condition can lead to inconsistency between the
state of hardware as expected by the driver.

Fix this by dropping the check for number of delay iterations.

While at it, also make __ew32_prepare() static as it's not used
anywhere else.

CC: stable <stable@vger.kernel.org>
Signed-off-by: Punit Agrawal <punit1.agrawal@toshiba.co.jp>
Reviewed-by: Alexander Duyck <alexander.h.duyck@linux.intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

e1000e: Revert "e1000e: Make watchdog use delayed work"

This reverts commit 59653e6497d16f7ac1d9db088f3959f57ee8c3db.

This is due to this commit causing driver crashes and connections to
reset unex

e1000e: Revert "e1000e: Make watchdog use delayed work"

This reverts commit 59653e6497d16f7ac1d9db088f3959f57ee8c3db.

This is due to this commit causing driver crashes and connections to
reset unexpectedly.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>

show more ...

PCI: Move ASPM declarations to linux/pci.h

Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:

PCIE_LIN

PCI: Move ASPM declarations to linux/pci.h

Move ASPM definitions and function prototypes from include/linux/pci-aspm.h
to include/linux/pci.h so users only need to include <linux/pci.h>:

PCIE_LINK_STATE_L0S
PCIE_LINK_STATE_L1
PCIE_LINK_STATE_CLKPM
pci_disable_link_state()
pci_disable_link_state_locked()
pcie_no_aspm()

No functional changes intended.

Link: https://lore.kernel.org/r/20190827095620.11213-1-kw@linux.com
Signed-off-by: Krzysztof Wilczynski <kw@linux.com>
Signed-off-by: Bjorn Helgaas <bhelgaas@google.com>

show more ...

e1000e: Make watchdog use delayed work

Use delayed work instead of timers to run the watchdog of the e1000e
driver.

Simplify the code with one less middle function.

Signed-off-by: Detlev Casanova

e1000e: Make watchdog use delayed work

Use delayed work instead of timers to run the watchdog of the e1000e
driver.

Simplify the code with one less middle function.

Signed-off-by: Detlev Casanova <detlev.casanova@gmail.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

e1000e: extend PTP gettime function to read system clock

This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@int

e1000e: extend PTP gettime function to read system clock

This adds support for the PTP_SYS_OFFSET_EXTENDED ioctl.

Cc: Richard Cochran <richardcochran@gmail.com>
Cc: Jacob Keller <jacob.e.keller@intel.com>
Cc: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: Miroslav Lichvar <mlichvar@redhat.com>
Acked-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

net: intel: Cleanup the copyright/license headers

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
adve

net: intel: Cleanup the copyright/license headers

After many years of having a ~30 line copyright and license header to our
source files, we are finally able to reduce that to one line with the
advent of the SPDX identifier.

Also caught a few files missing the SPDX license identifier, so fixed
them up.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Acked-by: Shannon Nelson <shannon.nelson@oracle.com>
Acked-by: Richard Cochran <richardcochran@gmail.com>
Tested-by: Andrew Bowers <andrewx.bowers@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

intel: add SPDX identifiers to all the Intel drivers

Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.

Signed-off-by: Jeff Ki

intel: add SPDX identifiers to all the Intel drivers

Add the SPDX identifiers to all the Intel wired LAN driver files, as
outlined in Documentation/process/license-rules.rst.

Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

e1000e: apply burst mode settings only on default

Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value

e1000e: apply burst mode settings only on default

Devices that support FLAG2_DMA_BURST have different default values
for RDTR and RADV. Apply burst mode default settings only when no
explicit value was passed at module load.

The RDTR default is zero. If the module is loaded for low latency
operation with RxIntDelay=0, do not override this value with a burst
default of 32.

Move the decision to apply burst values earlier, where explicitly
initialized module variables can be distinguished from defaults.

Signed-off-by: Willem de Bruijn <willemb@google.com>
Acked-by: Alexander Duyck <alexander.h.duyck@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

e1000e: add statistic indicating number of skipped Tx timestamps

The e1000e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request

e1000e: add statistic indicating number of skipped Tx timestamps

The e1000e driver can only handle one Tx timestamp request at a time.
This means it is possible for an application timestamp request to be
ignored.

There is no easy way for an administrator to determine if this occurred.
Add a new statistic which tracks this, tx_hwtstamp_skipped.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

e1000e: Add Support for 38.4MHZ frequency

Add support for 38.4MHz frequency is required for PTP
on CannonLake. SYSTIM frequency adjustment attributes for TIMINCA are
get/set dependent on the hardwar

e1000e: Add Support for 38.4MHZ frequency

Add support for 38.4MHz frequency is required for PTP
on CannonLake. SYSTIM frequency adjustment attributes for TIMINCA are
get/set dependent on the hardware clock frequency for a different
types of adapters. 38.4MHz frequency supported by CannonLake
and active once time synchronisation mechanism was enabled
Changed abbreviation from Hz to HZ to be compliant checkpatch code style

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

e1000e: Initial Support for CannonLake

i219 (6) and i219 (7) are the next LOM generations that will be
available on the nextIntel Client platform (CannonLake)
This patch provides the initial support

e1000e: Initial Support for CannonLake

i219 (6) and i219 (7) are the next LOM generations that will be
available on the nextIntel Client platform (CannonLake)
This patch provides the initial support for these devices

Signed-off-by: Sasha Neftin <sasha.neftin@intel.com>
Reviewed-by: Raanan Avargil <raanan.avargil@intel.com>
Reviewed-by: Dima Ruinskiy <dima.ruinskiy@intel.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

net: make ndo_get_stats64 a void function

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potenti

net: make ndo_get_stats64 a void function

The network device operation for reading statistics is only called
in one place, and it ignores the return value. Having a structure
return value is potentially confusing because some future driver could
incorrectly assume that the return value was used.

Fix all drivers with ndo_get_stats64 to have a void function.

Signed-off-by: Stephen Hemminger <sthemmin@microsoft.com>
Signed-off-by: David S. Miller <davem@davemloft.net>

show more ...

e1000e: factor out systim sanitization

This is prepatory work for an expanding list of adapter families that have
occasional ~10 hour clock jumps when being used for PTP. Factor out the
sanitization

e1000e: factor out systim sanitization

This is prepatory work for an expanding list of adapter families that have
occasional ~10 hour clock jumps when being used for PTP. Factor out the
sanitization function and convert to using a feature (bug) flag, per
suggestion from Jesse Brandeburg.

Littering functional code with device-specific checks is much messier than
simply checking a flag, and having device-specific init set flags as needed.
There are probably a number of other cases in the e1000e code that
could/should be converted similarly.

Suggested-by: Jesse Brandeburg <jesse.brandeburg@intel.com>
Signed-off-by: Jarod Wilson <jarod@redhat.com>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

e1000e: don't modify SYSTIM registers during SIOCSHWTSTAMP ioctl

The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happene

e1000e: don't modify SYSTIM registers during SIOCSHWTSTAMP ioctl

The e1000e_config_hwtstamp function was incorrectly resetting the SYSTIM
registers every time the ioctl was being run. If you happened to be
running ptp4l and lost the PTP connect (removing cable, or blocking the
UDP traffic for example), then ptp4l will eventually perform a restart
which involves re-requesting timestamp settings. In e1000e this has the
unfortunate and incorrect result of resetting SYSTIME to the kernel
time. Since kernel time is usually in UTC, and PTP time is in TAI, this
results in the leap second being re-applied.

Fix this by extracting the SYSTIME reset out into its own function,
e1000e_ptp_reset, which we call during reset to restore the hardware
registers. This function will (a) restart the timecounter based on the
new system time, (b) restore the previous PPB setting, and (c) restore
the previous hwtstamp settings.

In order to perform (b), I had to modify the adjfreq ptp function
pointer to store the old delta each time it is called. This also has the
side effect of restoring the correct base timinca register correctly.
The driver does not need to explicitly zero the ptp_delta variable since
the entire adapter structure comes zero-initialized.

Reported-by: Brian Walsh <brian@walsh.ws>
Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Tested-by: Brian Walsh <brian@walsh.ws>
Tested-by: Aaron Brown <aaron.f.brown@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...

e1000e: use BIT() macro for bit defines

This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying

e1000e: use BIT() macro for bit defines

This prevents signed bitshift issues when the shift would overwrite the
signed bit, and prevents making this mistake in the future when copying
and modifying code.

Use GENMASK or the unsigned postfix for cases which aren't suitable for
BIT() macro.

Signed-off-by: Jacob Keller <jacob.e.keller@intel.com>
Signed-off-by: Jeff Kirsher <jeffrey.t.kirsher@intel.com>

show more ...