can: mcba_usb: Fix termination command argument

Microchip USB Analyzer can activate the internal termination resistors
by setting the "termination" option ON, or OFF to to deactivate them.
As I've o

can: mcba_usb: Fix termination command argument

Microchip USB Analyzer can activate the internal termination resistors
by setting the "termination" option ON, or OFF to to deactivate them.
As I've observed, both with my oscilloscope and captured USB packets
below, you must send "0" to turn it ON, and "1" to turn it OFF.

From the schematics in the user's guide, I can confirm that you must
drive the CAN_RES signal LOW "0" to activate the resistors.

Reverse the argument value of usb_msg.termination to fix this.

These are the two commands sequence, ON then OFF.

> No. Time Source Destination Protocol Length Info
> 1 0.000000 host 1.3.1 USB 46 URB_BULK out
>
> Frame 1: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80000000000000000000000000000000000a8
>
> No. Time Source Destination Protocol Length Info
> 2 4.372547 host 1.3.1 USB 46 URB_BULK out
>
> Frame 2: 46 bytes on wire (368 bits), 46 bytes captured (368 bits)
> USB URB
> Leftover Capture Data: a80100000000000000000000000000000000a9

Signed-off-by: Yasushi SHOJI <yashi@spacecubics.com>
Link: https://lore.kernel.org/all/20221124152504.125994-1-yashi@spacecubics.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: dev: fix skb drop check

In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only
mode") the priv->ctrlmode element is read even on virtual CAN
interfaces that do not create the struct c

can: dev: fix skb drop check

In commit a6d190f8c767 ("can: skb: drop tx skb if in listen only
mode") the priv->ctrlmode element is read even on virtual CAN
interfaces that do not create the struct can_priv at startup. This
out-of-bounds read may lead to CAN frame drops for virtual CAN
interfaces like vcan and vxcan.

This patch mainly reverts the original commit and adds a new helper
for CAN interface drivers that provide the required information in
struct can_priv.

Fixes: a6d190f8c767 ("can: skb: drop tx skb if in listen only mode")
Reported-by: Dariusz Stojaczyk <Dariusz.Stojaczyk@opensynergy.com>
Cc: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Cc: Max Staudt <max@enpas.org>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Acked-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20221102095431.36831-1-socketcan@hartkopp.net
Cc: stable@vger.kernel.org # 6.0.x
[mkl: patch pch_can, too]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: tree-wide: advertise software timestamping capabilities

Currently, some CAN drivers support hardware timestamping, some do
not. But userland has no method to query which features are supported

can: tree-wide: advertise software timestamping capabilities

Currently, some CAN drivers support hardware timestamping, some do
not. But userland has no method to query which features are supported
(aside maybe of getting RX messages and observe whether or not
hardware timestamps stay at zero).

The canonical way for a network driver to advertised what kind of
timestamping it supports is to implement ethtool_ops::get_ts_info().

This patch only targets the CAN drivers which *do not* support
hardware timestamping. For each of those CAN drivers, implement the
get_ts_info() using the generic ethtool_op_get_ts_info().

This way, userland can do:

| $ ethtool --show-time-stamping canX

to confirm the device timestamping capacities.

N.B. the drivers which support hardware timestamping will be migrated
in separate patches.

Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/all/20220727101641.198847-6-mailhol.vincent@wanadoo.fr
[mkl: mscan: add missing mscan_ethtool_ops]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: can-dev: remove obsolete CAN LED support

Since commit 30f3b42147ba6f ("can: mark led trigger as broken") the
CAN specific LED support was disabled and marked as BROKEN. As the
common LED suppor

can: can-dev: remove obsolete CAN LED support

Since commit 30f3b42147ba6f ("can: mark led trigger as broken") the
CAN specific LED support was disabled and marked as BROKEN. As the
common LED support with CONFIG_LEDS_TRIGGER_NETDEV should do this work
now the code can be removed as preparation for a CAN netdevice Kconfig
rework.

Link: https://lore.kernel.org/all/20220518154527.29046-1-socketcan@hartkopp.net
Suggested-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
[mkl: remove led.h from MAINTAINERS]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb: properly check endpoint type

Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. We should check that in endpoint is actually present to
prevent this w

can: mcba_usb: properly check endpoint type

Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. We should check that in endpoint is actually present to
prevent this warning.

Found pipes are now saved to struct mcba_priv and code uses them
directly instead of making pipes in place.

Fail log:

| usb 5-1: BOGUS urb xfer, pipe 3 != type 1
| WARNING: CPU: 1 PID: 49 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| Modules linked in:
| CPU: 1 PID: 49 Comm: kworker/1:2 Not tainted 5.17.0-rc6-syzkaller-00184-g38f80f42147f #0
| Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
| Workqueue: usb_hub_wq hub_event
| RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| ...
| Call Trace:
| <TASK>
| mcba_usb_start drivers/net/can/usb/mcba_usb.c:662 [inline]
| mcba_usb_probe+0x8a3/0xc50 drivers/net/can/usb/mcba_usb.c:858
| usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
| call_driver_probe drivers/base/dd.c:517 [inline]

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/all/20220313100903.10868-1-paskripkin@gmail.com
Reported-and-tested-by: syzbot+3bc1dce0cc0052d60fde@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path

There is no need to call dev_kfree_skb() when usb_submit_urb() fails
because can_put_echo_skb() deletes original skb and

can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path

There is no need to call dev_kfree_skb() when usb_submit_urb() fails
because can_put_echo_skb() deletes original skb and
can_free_echo_skb() deletes the cloned skb.

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/all/20220311080208.45047-1-hbh25y@gmail.com
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: do not increase tx_bytes statistics for RTR frames

The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However

can: do not increase tx_bytes statistics for RTR frames

The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.

As such, net_device_stats::tx_bytes should not be increased when
sending RTR frames.

The function can_get_echo_skb() already returns the correct length,
even for RTR frames (c.f. [1]). However, for historical reasons, the
drivers do not use can_get_echo_skb()'s return value and instead, most
of them store a temporary length (or dlc) in some local structure or
array. Using the return value of can_get_echo_skb() solves the
issue. After doing this, such length/dlc fields become unused and so
this patch does the adequate cleaning when needed.

This patch fixes all the CAN drivers.

Finally, can_get_echo_skb() is decorated with the __must_check
attribute in order to force future drivers to correctly use its return
value (else the compiler would emit a warning).

[1] commit ed3320cec279 ("can: dev: __can_get_echo_skb():
fix real payload length return value for RTR frames")

Link: https://lore.kernel.org/all/20211207121531.42941-6-mailhol.vincent@wanadoo.fr
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Oliver Hartkopp <socketcan@hartkopp.net>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Cc: Andreas Larsson <andreas@gaisler.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
[mkl: add conversion for grcan]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: do not increase rx_bytes statistics for RTR frames

The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However

can: do not increase rx_bytes statistics for RTR frames

The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.

As such, net_device_stats::rx_bytes should not be increased for the
RTR frames.

This patch fixes all the CAN drivers.

Link: https://lore.kernel.org/all/20211207121531.42941-5-mailhol.vincent@wanadoo.fr
Cc: Marc Kleine-Budde <mkl@pengutronix.de>
Cc: Nicolas Ferre <nicolas.ferre@microchip.com>
Cc: Alexandre Belloni <alexandre.belloni@bootlin.com>
Cc: Ludovic Desroches <ludovic.desroches@microchip.com>
Cc: Chandrasekar Ramakrishnan <rcsekar@samsung.com>
Cc: Maxime Ripard <mripard@kernel.org>
Cc: Chen-Yu Tsai <wens@csie.org>
Cc: Jernej Skrabec <jernej.skrabec@gmail.com>
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Cc: Appana Durga Kedareswara rao <appana.durga.rao@xilinx.com>
Cc: Naga Sureshkumar Relli <naga.sureshkumar.relli@xilinx.com>
Cc: Michal Simek <michal.simek@xilinx.com>
Cc: Stephane Grosjean <s.grosjean@peak-system.com>
Tested-by: Jimmy Assarsson <extja@kvaser.com> # kvaser
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Acked-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Tested-by: Stefan Mätje <stefan.maetje@esd.eu> # esd_usb2
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: do not copy the payload of RTR frames

The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR f

can: do not copy the payload of RTR frames

The actual payload length of the CAN Remote Transmission Request (RTR)
frames is always 0, i.e. no payload is transmitted on the wire.
However, those RTR frames still use the DLC to indicate the length of
the requested frame.

For this reason, it is incorrect to copy the payload of RTR frames
(the payload buffer would only contain garbage data). This patch
encapsulates the payload copy in a check toward the RTR flag.

Link: https://lore.kernel.org/all/20211207121531.42941-4-mailhol.vincent@wanadoo.fr
Cc: Yasushi SHOJI <yashi@spacecubics.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb: properly check endpoint type

commit 136bed0bfd3bc9c95c88aafff2d22ecb3a919f23 upstream.

Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. We should c

can: mcba_usb: properly check endpoint type

commit 136bed0bfd3bc9c95c88aafff2d22ecb3a919f23 upstream.

Syzbot reported warning in usb_submit_urb() which is caused by wrong
endpoint type. We should check that in endpoint is actually present to
prevent this warning.

Found pipes are now saved to struct mcba_priv and code uses them
directly instead of making pipes in place.

Fail log:

| usb 5-1: BOGUS urb xfer, pipe 3 != type 1
| WARNING: CPU: 1 PID: 49 at drivers/usb/core/urb.c:502 usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| Modules linked in:
| CPU: 1 PID: 49 Comm: kworker/1:2 Not tainted 5.17.0-rc6-syzkaller-00184-g38f80f42147f #0
| Hardware name: QEMU Standard PC (Q35 + ICH9, 2009), BIOS 1.14.0-2 04/01/2014
| Workqueue: usb_hub_wq hub_event
| RIP: 0010:usb_submit_urb+0xed2/0x18a0 drivers/usb/core/urb.c:502
| ...
| Call Trace:
| <TASK>
| mcba_usb_start drivers/net/can/usb/mcba_usb.c:662 [inline]
| mcba_usb_probe+0x8a3/0xc50 drivers/net/can/usb/mcba_usb.c:858
| usb_probe_interface+0x315/0x7f0 drivers/usb/core/driver.c:396
| call_driver_probe drivers/base/dd.c:517 [inline]

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/all/20220313100903.10868-1-paskripkin@gmail.com
Reported-and-tested-by: syzbot+3bc1dce0cc0052d60fde@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path

commit 04c9b00ba83594a29813d6b1fb8fdc93a3915174 upstream.

There is no need to call dev_kfree_skb() when usb_submit_urb()

can: mcba_usb: mcba_usb_start_xmit(): fix double dev_kfree_skb in error path

commit 04c9b00ba83594a29813d6b1fb8fdc93a3915174 upstream.

There is no need to call dev_kfree_skb() when usb_submit_urb() fails
because can_put_echo_skb() deletes original skb and
can_free_echo_skb() deletes the cloned skb.

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/all/20220311080208.45047-1-hbh25y@gmail.com
Signed-off-by: Hangyu Hua <hbh25y@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

can: mcba_usb_start(): add missing urb->transfer_dma initialization

Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c02557174b ("can: mcba_usb: fix memory leak in
mc

can: mcba_usb_start(): add missing urb->transfer_dma initialization

Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c02557174b ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.

In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().

All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.

| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set

Fixes: 91c02557174b ("can: mcba_usb: fix memory leak in mcba_usb")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=990850
Link: https://lore.kernel.org/r/20210725103630.23864-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
[mkl: fixed typos in commit message - thanks Yasushi SHOJI]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb: fix memory leak in mcba_usb

Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.

In mcba_usb_start() 20 coher

can: mcba_usb: fix memory leak in mcba_usb

Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.

In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:

1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.

Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)

So, all allocated buffers should be freed with usb_free_coherent()
explicitly

NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: dev: can_free_echo_skb(): extend to return can frame length

In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stac

can: dev: can_free_echo_skb(): extend to return can frame length

In order to implement byte queue limits (bql) in CAN drivers, the
length of the CAN frame needs to be passed into the networking stack
even if the transmission failed for some reason.

To avoid to calculate this length twice, extend can_free_echo_skb() to
return that value. Convert all users of this function, too.

This patch is the natural extension of commit:

| 9420e1d495e2 ("can: dev: can_get_echo_skb(): extend to return can
| frame length")

Link: https://lore.kernel.org/r/20210319142700.305648-3-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb: remove h from printk format specifier

This change fixes the checkpatch warning described in this commit commit
cbacb5ab0aa0 ("docs: printk-formats: Stop encouraging use of unnecessary

can: mcba_usb: remove h from printk format specifier

This change fixes the checkpatch warning described in this commit commit
cbacb5ab0aa0 ("docs: printk-formats: Stop encouraging use of unnecessary
%h[xudi] and %hh[xudi]")

Standard integer promotion is already done and %hx and %hhx is useless so do
not encourage the use of %hh[xudi] or %h[xudi].

Link: https://lore.kernel.org/r/20210124150916.1920434-1-trix@redhat.com
Signed-off-by: Tom Rix <trix@redhat.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: dev: can_get_echo_skb(): extend to return can frame length

In order to implement byte queue limits (bql) in CAN drivers, the length of the
CAN frame needs to be passed into the networking stack

can: dev: can_get_echo_skb(): extend to return can frame length

In order to implement byte queue limits (bql) in CAN drivers, the length of the
CAN frame needs to be passed into the networking stack after queueing and after
transmission completion.

To avoid to calculate this length twice, extend can_get_echo_skb() to return
that value. Convert all users of this function, too.

Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-14-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: dev: can_put_echo_skb(): extend to handle frame_len

Add a frame_len argument to can_put_echo_skb() which is used to save length of
the CAN frame into field frame_len of struct can_skb_priv so t

can: dev: can_put_echo_skb(): extend to handle frame_len

Add a frame_len argument to can_put_echo_skb() which is used to save length of
the CAN frame into field frame_len of struct can_skb_priv so that it can be
later used after transmission completion. Convert all users of this function,
too.

Drivers which implement BQL call can_put_echo_skb() with the output of
can_skb_get_frame_len(skb) and drivers which do not simply pass zero as an
input (in the same way that NULL would be given to can_get_echo_skb()). This
way, we have a nice symmetry between the two echo functions.

Link: https://lore.kernel.org/r/20210111061335.39983-1-mailhol.vincent@wanadoo.fr
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Reviewed-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>
Link: https://lore.kernel.org/r/20210111141930.693847-13-mkl@pengutronix.de
Signed-off-by: Vincent Mailhol <mailhol.vincent@wanadoo.fr>

show more ...

can: replace can_dlc as variable/element for payload length

The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but i

can: replace can_dlc as variable/element for payload length

The naming of can_dlc as element of struct can_frame and also as variable
name is misleading as it claims to be a 'data length CODE' but in reality
it always was a plain data length.

With the indroduction of a new 'len' element in struct can_frame we can now
remove can_dlc as name and make clear which of the former uses was a plain
length (-> 'len') or a data length code (-> 'dlc') value.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201120100444.3199-1-socketcan@hartkopp.net
[mkl: gs_usb: keep struct gs_host_frame::can_dlc as is]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: rename get_can_dlc() macro with can_cc_dlc2len()

The get_can_dlc() macro is used to ensure the payload length information of
the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN).

Renam

can: rename get_can_dlc() macro with can_cc_dlc2len()

The get_can_dlc() macro is used to ensure the payload length information of
the Classical CAN frame to be max 8 bytes (the CAN_MAX_DLEN).

Rename the macro and use the correct constant in preparation of the len/dlc
cleanup for Classical CAN frames.

Signed-off-by: Oliver Hartkopp <socketcan@hartkopp.net>
Link: https://lore.kernel.org/r/20201110101852.1973-3-socketcan@hartkopp.net
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb_start(): add missing urb->transfer_dma initialization

commit fc43fb69a7af92839551f99c1a96a37b77b3ae7a upstream.

Yasushi reported, that his Microchip CAN Analyzer stopped working
since

can: mcba_usb_start(): add missing urb->transfer_dma initialization

commit fc43fb69a7af92839551f99c1a96a37b77b3ae7a upstream.

Yasushi reported, that his Microchip CAN Analyzer stopped working
since commit 91c02557174b ("can: mcba_usb: fix memory leak in
mcba_usb"). The problem was in missing urb->transfer_dma
initialization.

In my previous patch to this driver I refactored mcba_usb_start() code
to avoid leaking usb coherent buffers. To archive it, I passed local
stack variable to usb_alloc_coherent() and then saved it to private
array to correctly free all coherent buffers on ->close() call. But I
forgot to initialize urb->transfer_dma with variable passed to
usb_alloc_coherent().

All of this was causing device to not work, since dma addr 0 is not
valid and following log can be found on bug report page, which points
exactly to problem described above.

| DMAR: [DMA Write] Request device [00:14.0] PASID ffffffff fault addr 0 [fault reason 05] PTE Write access is not set

Fixes: 91c02557174b ("can: mcba_usb: fix memory leak in mcba_usb")
Link: https://bugs.debian.org/cgi-bin/bugreport.cgi?bug=990850
Link: https://lore.kernel.org/r/20210725103630.23864-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-by: Yasushi SHOJI <yasushi.shoji@gmail.com>
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Tested-by: Yasushi SHOJI <yashi@spacecubics.com>
[mkl: fixed typos in commit message - thanks Yasushi SHOJI]
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

can: mcba_usb: fix memory leak in mcba_usb

commit 91c02557174be7f72e46ed7311e3bea1939840b0 upstream.

Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem

can: mcba_usb: fix memory leak in mcba_usb

commit 91c02557174be7f72e46ed7311e3bea1939840b0 upstream.

Syzbot reported memory leak in SocketCAN driver for Microchip CAN BUS
Analyzer Tool. The problem was in unfreed usb_coherent.

In mcba_usb_start() 20 coherent buffers are allocated and there is
nothing, that frees them:

1) In callback function the urb is resubmitted and that's all
2) In disconnect function urbs are simply killed, but URB_FREE_BUFFER
is not set (see mcba_usb_start) and this flag cannot be used with
coherent buffers.

Fail log:
| [ 1354.053291][ T8413] mcba_usb 1-1:0.0 can0: device disconnected
| [ 1367.059384][ T8420] kmemleak: 20 new suspected memory leaks (see /sys/kernel/debug/kmem)

So, all allocated buffers should be freed with usb_free_coherent()
explicitly

NOTE:
The same pattern for allocating and freeing coherent buffers
is used in drivers/net/can/usb/kvaser_usb/kvaser_usb_core.c

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Link: https://lore.kernel.org/r/20210609215833.30393-1-paskripkin@gmail.com
Cc: linux-stable <stable@vger.kernel.org>
Reported-and-tested-by: syzbot+57281c762a3922e14dfe@syzkaller.appspotmail.com
Signed-off-by: Pavel Skripkin <paskripkin@gmail.com>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb()

The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the ca

can: mcba_usb: mcba_usb_start_xmit(): first fill skb, then pass to can_put_echo_skb()

The driver has to first fill the skb with data and then handle it to
can_put_echo_skb(). This patch moves the can_put_echo_skb() down, right before
sending the skb out via USB.

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Link: https://lore.kernel.org/r/20201111221204.1639007-1-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb: remove redundant initialization of variable err

The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initializati

can: mcba_usb: remove redundant initialization of variable err

The variable err is being initialized with a value that is never read
and it is being updated later with a new value. The initialization is
redundant and can be removed.

Addresses-Coverity: ("Unused value")
Signed-off-by: Colin Ian King <colin.king@canonical.com>
Link: https://lore.kernel.org/r/20200706164240.518623-1-colin.king@canonical.com
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: drivers: fix spelling mistakes

This patch fixes spelling erros found by "codespell" in the
drivers/net/can subtree.

Link: https://lore.kernel.org/r/20200915223527.1417033-6-mkl@pengutronix.de

can: drivers: fix spelling mistakes

This patch fixes spelling erros found by "codespell" in the
drivers/net/can subtree.

Link: https://lore.kernel.org/r/20200915223527.1417033-6-mkl@pengutronix.de
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...

can: mcba_usb: fix use-after-free on disconnect

The driver was accessing its driver data after having freed it.

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc:

can: mcba_usb: fix use-after-free on disconnect

The driver was accessing its driver data after having freed it.

Fixes: 51f3baad7de9 ("can: mcba_usb: Add support for Microchip CAN BUS Analyzer")
Cc: stable <stable@vger.kernel.org> # 4.12
Cc: Remigiusz Kołłątaj <remigiusz.kollataj@mobica.com>
Reported-by: syzbot+e29b17e5042bbc56fae9@syzkaller.appspotmail.com
Signed-off-by: Johan Hovold <johan@kernel.org>
Signed-off-by: Marc Kleine-Budde <mkl@pengutronix.de>

show more ...