media: qcom: camss: Comment CSID dt_id field

commit f910d3ba78a2677c23508f225eb047d89eb4b2b6 upstream.

Digging into the documentation we find that the DT_ID bitfield is used to
map the six bit DT t

media: qcom: camss: Comment CSID dt_id field

commit f910d3ba78a2677c23508f225eb047d89eb4b2b6 upstream.

Digging into the documentation we find that the DT_ID bitfield is used to
map the six bit DT to a two bit ID code. This value is concatenated to the
VC bitfield to create a CID value. DT_ID is the two least significant bits
of CID and VC the most significant bits.

Originally we set dt_id = vc * 4 in and then subsequently set dt_id = vc.

commit 3c4ed72a16bc ("media: camss: sm8250: Virtual channels for CSID")
silently fixed the multiplication by four which would give a better
value for the generated CID without mentioning what was being done or why.

Next up I haplessly changed the value back to "dt_id = vc * 4" since there
didn't appear to be any logic behind it.

Hans asked what the change was for and I honestly couldn't remember the
provenance of it, so I dug in.

Link: https://lore.kernel.org/linux-arm-msm/edd4bf9b-0e1b-883c-1a4d-50f4102c3924@xs4all.nl/

Add a comment so the next hapless programmer doesn't make this same
mistake.

Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

media: qcom: camss: Fix csid-gen2 for test pattern generator

commit 87889f1b7ea40d2544b49c62092e6ef2792dced7 upstream.

In the current driver csid Test Pattern Generator (TPG) doesn't work.
This cha

media: qcom: camss: Fix csid-gen2 for test pattern generator

commit 87889f1b7ea40d2544b49c62092e6ef2792dced7 upstream.

In the current driver csid Test Pattern Generator (TPG) doesn't work.
This change:
- fixes writing frame width and height values into CSID_TPG_DT_n_CFG_0
- fixes the shift by one between test_pattern control value and the
actual pattern.
- drops fixed VC of 0x0a which testing showed prohibited some test
patterns in the CSID to produce output.
So that TPG starts working, but with the below limitations:
- only test_pattern=9 works as it should
- test_pattern=8 and test_pattern=7 produce black frame (all zeroes)
- the rest of test_pattern's don't work (yavta doesn't get the data)
- regardless of the CFA pattern set by 'media-ctl -V' the actual pixel
order is always the same (RGGB for any RAW8 or RAW10P format in
4608x2592 resolution).

Tested with:

RAW10P format, VC0:
media-ctl -V '"msm_csid0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video0

RAW10P format, VC1:
media-ctl -V '"msm_csid0":2[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi1":0[fmt:SRGGB10/4608x2592 field:none]'
media-ctl -l '"msm_csid0":2->"msm_vfe0_rdi1":0[1]'
v4l2-ctl -d /dev/v4l-subdev6 -c test_pattern=9
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB10P -s 4608x2592 /dev/video1

RAW8 format, VC0:
media-ctl --reset
media-ctl -V '"msm_csid0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -V '"msm_vfe0_rdi0":0[fmt:SRGGB8/4608x2592 field:none]'
media-ctl -l '"msm_csid0":1->"msm_vfe0_rdi0":0[1]'
yavta -B capture-mplane --capture=3 -n 3 -f SRGGB8 -s 4608x2592 /dev/video0

Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Andrey Konovalov <andrey.konovalov@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3

commit e655d1ae9703286cef7fda8675cad62f649dc183 upstream.

VC_MODE = 0 implies a two bit VC address.
VC_MODE = 1 is require

media: qcom: camss: Fix set CSI2_RX_CFG1_VC_MODE when VC is greater than 3

commit e655d1ae9703286cef7fda8675cad62f649dc183 upstream.

VC_MODE = 0 implies a two bit VC address.
VC_MODE = 1 is required for VCs with a larger address than two bits.

Fixes: eebe6d00e9bf ("media: camss: Add support for CSID hardware version Titan 170")
Cc: stable@vger.kernel.org
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

media: camss: sm8250: Virtual channels for CSID

CSID hardware on SM8250 can demux up to 4 simultaneous streams
based on virtual channel (vc) or datatype (dt).
The CSID subdevice entity now has 4 sou

media: camss: sm8250: Virtual channels for CSID

CSID hardware on SM8250 can demux up to 4 simultaneous streams
based on virtual channel (vc) or datatype (dt).
The CSID subdevice entity now has 4 source ports that can be
enabled/disabled and thus can control which virtual channels
are enabled. Datatype demuxing not tested.

In order to keep a valid internal state of the subdevice,
implicit format propagation from the sink to the source pads
has been preserved. However, the format on each source pad
can be different and in that case it must be configured explicitly.

CSID's s_stream is called when any stream is started or stopped.
It will call configure_streams() that will rewrite IRQ settings to HW.
When multiple streams are running simultaneously there is an issue
when writing IRQ settings for one stream while another is still
running, thus avoid re-writing settings if they were not changed
in link setup, or by fully powering off the CSID hardware.

Signed-off-by: Milen Mitkov <quic_mmitkov@quicinc.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Acked-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: camss: Replace hard coded value with parameter

Kernel test robot reported below warning ->
drivers/media/platform/qcom/camss/camss-csid-gen2.c:407:3:
warning: Value stored to 'val' is never r

media: camss: Replace hard coded value with parameter

Kernel test robot reported below warning ->
drivers/media/platform/qcom/camss/camss-csid-gen2.c:407:3:
warning: Value stored to 'val' is never read
[clang-analyzer-deadcode.DeadStores]

Replace hard coded value with val.

Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Souptick Joarder (HPE) <jrdr.linux@gmail.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: camss: add support for SM8250 camss

The Titan 480 camss found on SM8250 has 6 CSIPHY and 4 VFE/CSID.

CSID is compatible with the Titan 170 CSID, but the Titan 480 CSID are
inside the VFE reg

media: camss: add support for SM8250 camss

The Titan 480 camss found on SM8250 has 6 CSIPHY and 4 VFE/CSID.

CSID is compatible with the Titan 170 CSID, but the Titan 480 CSID are
inside the VFE region (between the "top" and "bus" registers), so a
workaround is added to avoid ioremap failure.

[bod] Fixed setting camnoc_axi_clk_src instead of camcc_camnoc_axi_clk
[jgrahsl, bod] Add slow_ahb_src clock values
[jgrahsl, bod] Add cpa_ahb clock values

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Julian Grahsl <jgrahsl@snap.com>
Co-developed-by: Julian Grahsl <jgrahsl@snap.com>
Signed-off-by: Julian Grahsl <jgrahsl@snap.com>
Reviewed-by: Robert Foss <robert.foss@linaro.org>
Co-developed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...