media: i2c: imx334: update pixel, hblank and link frequency

Update pixel_rate and link frequency for 1920x1080@30
while changing mode.

Update vblank value while changing mode

Add support to handle

media: i2c: imx334: update pixel, hblank and link frequency

Update pixel_rate and link frequency for 1920x1080@30
while changing mode.

Update vblank value while changing mode

Add support to handle multiple link frequencies.

Add dummy ctrl cases for pixel_rate and link frequency
to avoid error while changing the modes dynamically.

Update default link frequency from device tree max link
frequency value.

Update init_cfg() function to update the link frequency
menu_skip_mask value.

Suggested-by: Sakari Ailus <sakari.ailus@iki.fi>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
[Sakari Ailus: Document menu_skip_mask, remove extra blank line.]
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f

media: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
commit 03c835f498b5 ("i2c: Switch .probe() to not take an id parameter")
convert back to (the new) .probe() to be able to eventually drop
.probe_new() from struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>

show more ...

media: i2c: imx334: support lower bandwidth mode

Some platforms may not be capable of supporting the bandwidth
required for 12 bit or 3840x2160@60 resolutions.

Add support for dynamically selecting

media: i2c: imx334: support lower bandwidth mode

Some platforms may not be capable of supporting the bandwidth
required for 12 bit or 3840x2160@60 resolutions.

Add support for dynamically selecting 10 bit and 1920x1080@30
resolutions while leaving the existing configuration as default.

Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
CC: Conor Dooley <conor.dooley@microchip.com>
Signed-off-by: Prakash Battu <Prakash.Battu@microchip.com>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

media: i2c: imx334: add missing reset values for mode 3840x2160_regs[]

There are some missing reset reg_mode values for the 3840x2160@60
resolution. The camera sensor still works in 3840x2160@60 res

media: i2c: imx334: add missing reset values for mode 3840x2160_regs[]

There are some missing reset reg_mode values for the 3840x2160@60
resolution. The camera sensor still works in 3840x2160@60 resolution mode
because of the register reset values. This is an issue when we change the
modes dynamically. As an example, when we change the mode from 1920x1080@30
resolution to 3840x2160@60 resoultion then the mode values will be written
to the registers from the array mode_3840x2160_regs[] which gives the wrong
output which is incorrect resolution.

So add the missing reset values to the mode_3840x2160_regs[].

Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

media: i2c: imx334: replace __v4l2_ctrl_s_ctrl to __v4l2_ctrl_modify_range

For every mode we will get new set of values for hbalnk so use
__v4l2_ctrl_modify_range() to support multi modes for hblank

media: i2c: imx334: replace __v4l2_ctrl_s_ctrl to __v4l2_ctrl_modify_range

For every mode we will get new set of values for hbalnk so use
__v4l2_ctrl_modify_range() to support multi modes for hblank.

The hblank value is readonly in the driver. because of this the function
returns error if we try to change. so added dumy return case in
imx334_set_ctrl function.

Reviewed-by: Jacopo Mondi <jacopo.mondi@ideasonboard.com>
Suggested-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Shravan Chippa <shravan.chippa@microchip.com>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab@kernel.org>

show more ...

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

i2c: Make remove callback return void

The value returned by an i2c driver's remove function is mostly ignored.
(Only an error message is printed if the value is non-zero that the
error is ignored.)

So change the prototype of the remove function to return no value. This
way driver authors are not tempted to assume that passing an error to
the upper layer is a good idea. All drivers are adapted accordingly.
There is no intended change of behaviour, all callbacks were prepared to
return 0 before.

Reviewed-by: Peter Senna Tschudin <peter.senna@gmail.com>
Reviewed-by: Jeremy Kerr <jk@codeconstruct.com.au>
Reviewed-by: Benjamin Mugnier <benjamin.mugnier@foss.st.com>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Reviewed-by: Crt Mori <cmo@melexis.com>
Reviewed-by: Heikki Krogerus <heikki.krogerus@linux.intel.com>
Acked-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
Acked-by: Marek Behún <kabel@kernel.org> # for leds-turris-omnia
Acked-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Reviewed-by: Petr Machata <petrm@nvidia.com> # for mlxsw
Reviewed-by: Maximilian Luz <luzmaximilian@gmail.com> # for surface3_power
Acked-by: Srinivas Pandruvada <srinivas.pandruvada@linux.intel.com> # for bmc150-accel-i2c + kxcjk-1013
Reviewed-by: Hans Verkuil <hverkuil-cisco@xs4all.nl> # for media/* + staging/media/*
Acked-by: Miguel Ojeda <ojeda@kernel.org> # for auxdisplay/ht16k33 + auxdisplay/lcd2s
Reviewed-by: Luca Ceresoli <luca.ceresoli@bootlin.com> # for versaclock5
Reviewed-by: Ajay Gupta <ajayg@nvidia.com> # for ucsi_ccg
Acked-by: Jonathan Cameron <Jonathan.Cameron@huawei.com> # for iio
Acked-by: Peter Rosin <peda@axentia.se> # for i2c-mux-*, max9860
Acked-by: Adrien Grassein <adrien.grassein@gmail.com> # for lontium-lt8912b
Reviewed-by: Jean Delvare <jdelvare@suse.de> # for hwmon, i2c-core and i2c/muxes
Acked-by: Corey Minyard <cminyard@mvista.com> # for IPMI
Reviewed-by: Vladimir Oltean <olteanv@gmail.com>
Acked-by: Dmitry Torokhov <dmitry.torokhov@gmail.com>
Acked-by: Sebastian Reichel <sebastian.reichel@collabora.com> # for drivers/power
Acked-by: Krzysztof Hałasa <khalasa@piap.pl>
Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

show more ...

media: v4l2-subdev: add subdev-wide state struct

We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs i

media: v4l2-subdev: add subdev-wide state struct

We have 'struct v4l2_subdev_pad_config' which contains configuration for
a single pad used for the TRY functionality, and an array of those
structs is passed to various v4l2_subdev_pad_ops.

I was working on subdev internal routing between pads, and realized that
there's no way to add TRY functionality for routes, which is not pad
specific configuration. Adding a separate struct for try-route config
wouldn't work either, as e.g. set-fmt needs to know the try-route
configuration to propagate the settings.

This patch adds a new struct, 'struct v4l2_subdev_state' (which at the
moment only contains the v4l2_subdev_pad_config array) and the new
struct is used in most of the places where v4l2_subdev_pad_config was
used. All v4l2_subdev_pad_ops functions taking v4l2_subdev_pad_config
are changed to instead take v4l2_subdev_state.

The changes to drivers/media/v4l2-core/v4l2-subdev.c and
include/media/v4l2-subdev.h were written by hand, and all the driver
changes were done with the semantic patch below. The spatch needs to be
applied to a select list of directories. I used the following shell
commands to apply the spatch:

dirs="drivers/media/i2c drivers/media/platform drivers/media/usb drivers/media/test-drivers/vimc drivers/media/pci drivers/staging/media"
for dir in $dirs; do spatch -j8 --dir --include-headers --no-show-diff --in-place --sp-file v4l2-subdev-state.cocci $dir; done

Note that Coccinelle chokes on a few drivers (gcc extensions?). With
minor changes we can make Coccinelle run fine, and these changes can be
reverted after spatch. The diff for these changes is:

For drivers/media/i2c/s5k5baf.c:

@@ -1481,7 +1481,7 @@ static int s5k5baf_set_selection(struct v4l2_subdev *sd,
&s5k5baf_cis_rect,
v4l2_subdev_get_try_crop(sd, cfg, PAD_CIS),
v4l2_subdev_get_try_compose(sd, cfg, PAD_CIS),
- v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT)
+ v4l2_subdev_get_try_crop(sd, cfg, PAD_OUT),
};
s5k5baf_set_rect_and_adjust(rects, rtype, &sel->r);
return 0;

For drivers/media/platform/s3c-camif/camif-capture.c:

@@ -1230,7 +1230,7 @@ static int s3c_camif_subdev_get_fmt(struct v4l2_subdev *sd,
*mf = camif->mbus_fmt;
break;

- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* crop rectangle at camera interface input */
mf->width = camif->camif_crop.width;
mf->height = camif->camif_crop.height;
@@ -1332,7 +1332,7 @@ static int s3c_camif_subdev_set_fmt(struct v4l2_subdev *sd,
}
break;

- case CAMIF_SD_PAD_SOURCE_C...CAMIF_SD_PAD_SOURCE_P:
+ case CAMIF_SD_PAD_SOURCE_C:
/* Pixel format can be only changed on the sink pad. */
mf->code = camif->mbus_fmt.code;
mf->width = crop->width;

The semantic patch is:

// <smpl>

// Change function parameter

@@
identifier func;
identifier cfg;
@@

func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...)
{
<...
- cfg
+ sd_state
...>
}

// Change function declaration parameter

@@
identifier func;
identifier cfg;
type T;
@@
T func(...,
- struct v4l2_subdev_pad_config *cfg
+ struct v4l2_subdev_state *sd_state
, ...);

// Change function return value

@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...)
{
...
}

// Change function declaration return value

@@
identifier func;
@@
- struct v4l2_subdev_pad_config
+ struct v4l2_subdev_state
*func(...);

// Some drivers pass a local pad_cfg for a single pad to a called function. Wrap it
// inside a pad_state.

@@
identifier func;
identifier pad_cfg;
@@
func(...)
{
...
struct v4l2_subdev_pad_config pad_cfg;
+ struct v4l2_subdev_state pad_state = { .pads = &pad_cfg };

<+...

(
v4l2_subdev_call
|
sensor_call
|
isi_try_fse
|
isc_try_fse
|
saa_call_all
)
(...,
- &pad_cfg
+ &pad_state
,...)

...+>
}

// If the function uses fields from pad_config, access via state->pads

@@
identifier func;
identifier state;
@@
func(...,
struct v4l2_subdev_state *state
, ...)
{
<...
(
- state->try_fmt
+ state->pads->try_fmt
|
- state->try_crop
+ state->pads->try_crop
|
- state->try_compose
+ state->pads->try_compose
)
...>
}

// If the function accesses the filehandle, use fh->state instead

@@
struct v4l2_subdev_fh *fh;
@@
- fh->pad
+ fh->state

@@
struct v4l2_subdev_fh fh;
@@
- fh.pad
+ fh.state

// Start of vsp1 specific

@@
@@
struct vsp1_entity {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
};

@@
symbol entity;
@@
vsp1_entity_init(...)
{
...
entity->config =
- v4l2_subdev_alloc_pad_config
+ v4l2_subdev_alloc_state
(&entity->subdev);
...
}

@@
symbol entity;
@@
vsp1_entity_destroy(...)
{
...
- v4l2_subdev_free_pad_config
+ v4l2_subdev_free_state
(entity->config);
...
}

@exists@
identifier func =~ "(^vsp1.*)|(hsit_set_format)|(sru_enum_frame_size)|(sru_set_format)|(uif_get_selection)|(uif_set_selection)|(uds_enum_frame_size)|(uds_set_format)|(brx_set_format)|(brx_get_selection)|(histo_get_selection)|(histo_set_selection)|(brx_set_selection)";
symbol config;
@@
func(...) {
...
- struct v4l2_subdev_pad_config *config;
+ struct v4l2_subdev_state *config;
...
}

// End of vsp1 specific

// Start of rcar specific

@@
identifier sd;
identifier pad_cfg;
@@
rvin_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}

// End of rcar specific

// Start of rockchip specific

@@
identifier func =~ "(rkisp1_rsz_get_pad_fmt)|(rkisp1_rsz_get_pad_crop)|(rkisp1_rsz_register)";
symbol rsz;
symbol pad_cfg;
@@

func(...)
{
+ struct v4l2_subdev_state state = { .pads = rsz->pad_cfg };
...
- rsz->pad_cfg
+ &state
...
}

@@
identifier func =~ "(rkisp1_isp_get_pad_fmt)|(rkisp1_isp_get_pad_crop)";
symbol isp;
symbol pad_cfg;
@@

func(...)
{
+ struct v4l2_subdev_state state = { .pads = isp->pad_cfg };
...
- isp->pad_cfg
+ &state
...
}

@@
symbol rkisp1;
symbol isp;
symbol pad_cfg;
@@

rkisp1_isp_register(...)
{
+ struct v4l2_subdev_state state = { .pads = rkisp1->isp.pad_cfg };
...
- rkisp1->isp.pad_cfg
+ &state
...
}

// End of rockchip specific

// Start of tegra-video specific

@@
identifier sd;
identifier pad_cfg;
@@
__tegra_channel_try_format(...)
{
...
- struct v4l2_subdev_pad_config *pad_cfg;
+ struct v4l2_subdev_state *sd_state;
...
- pad_cfg = v4l2_subdev_alloc_pad_config(sd);
+ sd_state = v4l2_subdev_alloc_state(sd);
<...
- pad_cfg
+ sd_state
...>
- v4l2_subdev_free_pad_config(pad_cfg);
+ v4l2_subdev_free_state(sd_state);
...
}

@@
identifier sd_state;
@@
__tegra_channel_try_format(...)
{
...
struct v4l2_subdev_state *sd_state;
<...
- sd_state->try_crop
+ sd_state->pads->try_crop
...>
}

// End of tegra-video specific

// </smpl>

Signed-off-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Acked-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Acked-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

show more ...

media: i2c: imx334: fix the pm runtime get logic

The PM runtime get logic is currently broken, as it checks if
ret is zero instead of checking if it is an error code,
as reported by Dan Carpenter.

media: i2c: imx334: fix the pm runtime get logic

The PM runtime get logic is currently broken, as it checks if
ret is zero instead of checking if it is an error code,
as reported by Dan Carpenter.

While here, use the pm_runtime_resume_and_get() as added by:
commit dd8088d5a896 ("PM: runtime: Add pm_runtime_resume_and_get to deal with usage counter")
added pm_runtime_resume_and_get() in order to automatically handle
dev->power.usage_count decrement on errors. As a bonus, such function
always return zero on success.

It should also be noticed that a fail of pm_runtime_get_sync() would
potentially result in a spurious runtime_suspend(), instead of
using pm_runtime_put_noidle().

Reported-by: Dan Carpenter <dan.carpenter@oracle.com>
Reviewed-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Reviewed-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

show more ...

media: v4l: fwnode: Rename v4l2_async_register_subdev_sensor_common

Rename v4l2_async_register_subdev_sensor_common as
v4l2_async_register_subdev_sensor. This is a part of the effort to make
the lon

media: v4l: fwnode: Rename v4l2_async_register_subdev_sensor_common

Rename v4l2_async_register_subdev_sensor_common as
v4l2_async_register_subdev_sensor. This is a part of the effort to make
the long names present in V4L2 fwnode and async frameworks shorter.

Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Reviewed-by: Ezequiel Garcia <ezequiel@collabora.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

show more ...

media: imx334: 'ret' is uninitialized, should have been PTR_ERR()

Fix this compiler warning:

drivers/media/i2c/imx334.c: In function 'imx334_parse_hw_config':
include/linux/dev_printk.h:112:2: warn

media: imx334: 'ret' is uninitialized, should have been PTR_ERR()

Fix this compiler warning:

drivers/media/i2c/imx334.c: In function 'imx334_parse_hw_config':
include/linux/dev_printk.h:112:2: warning: 'ret' may be used uninitialized in this function [-Wmaybe-uninitialized]
112 | _dev_err(dev, dev_fmt(fmt), ##__VA_ARGS__)
| ^~~~~~~~
drivers/media/i2c/imx334.c:783:6: note: 'ret' was declared here
783 | int ret;
| ^~~

Signed-off-by: Hans Verkuil <hverkuil-cisco@xs4all.nl>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

show more ...

media: i2c: Add imx334 camera sensor driver

Add a v4l2 sub-device driver for the Sony imx334 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.

The foll

media: i2c: Add imx334 camera sensor driver

Add a v4l2 sub-device driver for the Sony imx334 image sensor.
This is a camera sensor using the i2c bus for control and the
csi-2 bus for data.

The following features are supported:
- manual exposure and analog gain control support
- vblank/hblank/pixel rate/link freq control support
- supported resolution:
- 3840x2160 @ 60fps
- supported bayer order output:
- SRGGB12

Signed-off-by: Martina Krasteva <martinax.krasteva@intel.com>
Reviewed-by: Gjorgji Rosikopulos <gjorgjix.rosikopulos@intel.com>
Acked-by: Daniele Alessandrelli <daniele.alessandrelli@intel.com>
Acked-by: Paul J. Murphy <paul.j.murphy@intel.com>
Reviewed-by: Jacopo Mondi <jacopo@jmondi.org>
Signed-off-by: Sakari Ailus <sakari.ailus@linux.intel.com>
Signed-off-by: Mauro Carvalho Chehab <mchehab+huawei@kernel.org>

show more ...