iio: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i

iio: Switch i2c drivers back to use .probe()

After commit b8a1a4cd5a98 ("i2c: Provide a temporary .probe_new()
call-back type"), all drivers being converted to .probe_new() and then
03c835f498b5 ("i2c: Switch .probe() to not take an id parameter") convert
back to (the new) .probe() to be able to eventually drop .probe_new() from
struct i2c_driver.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Link: https://lore.kernel.org/r/20230515205048.19561-1-u.kleine-koenig@pengutronix.de
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: pressure: dlhl60d: Convert to i2c's .probe_new()

.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.

Signed-off-by: Uwe Kleine-König <u.

iio: pressure: dlhl60d: Convert to i2c's .probe_new()

.probe_new() doesn't get the i2c_device_id * parameter, so determine
that explicitly in the probe function.

Signed-off-by: Uwe Kleine-König <u.kleine-koenig@pengutronix.de>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20221118224540.619276-168-uwe@kleine-koenig.org
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: pressure: dlhl60d: Don't take garbage into consideration when reading data

Both pressure and temperature are 24-bit long. Use proper accessors
instead of overlapping readings.

Signed-off-by: A

iio: pressure: dlhl60d: Don't take garbage into consideration when reading data

Both pressure and temperature are 24-bit long. Use proper accessors
instead of overlapping readings.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Link: https://lore.kernel.org/r/20220726142048.4494-1-andriy.shevchenko@linux.intel.com
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: pressure: dlhl60d: Drop unnecessary alignment forcing.

I2C doesn't use the buffers directly for DMA so there is no need
to enforce alignment.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@

iio: pressure: dlhl60d: Drop unnecessary alignment forcing.

I2C doesn't use the buffers directly for DMA so there is no need
to enforce alignment.

Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>
Cc: Tomislav Denis <tomislav.denis@avl.com>
Acked-by: Nuno Sá <nuno.sa@analog.com>
Link: https://lore.kernel.org/r/20220508175712.647246-86-jic23@kernel.org

show more ...

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
F

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: Remove superfluous of_node assignments

If a driver does not assign an of_node to a IIO device to IIO core will
automatically assign the of_node of the parent device. This automatic
assignment i

iio: Remove superfluous of_node assignments

If a driver does not assign an of_node to a IIO device to IIO core will
automatically assign the of_node of the parent device. This automatic
assignment is done in the iio_device_register() function.

There is a fair amount of drivers that currently manually assign the
of_node of the IIO device. All but 4 of them can make use of the automatic
assignment though.

The exceptions are:
* mxs-lradc-adc: Which uses the of_node of the parent of the parent.
* stm32-dfsdm-adc, stm32-adc and stm32-dac: Which reference the of_node
assigned to the IIO device before iio_device_register() is called.

All other drivers are updated to use automatic assignment. This reduces
the amount of boilerplate code involved in setting up the IIO device.

The patch has mostly been auto-generated with the following semantic patch

// <smpl>
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(&parent, ...)
...
-indio_dev->dev.of_node = parent.of_node;

@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(parent, ...)
...
-indio_dev->dev.of_node = parent->of_node;
// </smpl>

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;

It updates 302

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;

It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'

But this is is only done in case where the block is left empty.

The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.

However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: pressure: Add driver for DLH pressure sensors

All Sensors DLH is series of low voltage digital pressure sensors.
Additionally to pressure value sensors deliver a temperature value.
Sensors can

iio: pressure: Add driver for DLH pressure sensors

All Sensors DLH is series of low voltage digital pressure sensors.
Additionally to pressure value sensors deliver a temperature value.
Sensors can be accessed over I2C and SPI, this driver supports
only I2C access.

Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

De

Replace HTTP links with HTTPS ones: drivers/iio

Rationale:
Reduces attack surface on kernel devs opening the links for MITM
as HTTPS traffic is much harder to manipulate.

Deterministic algorithm:
For each file:
If not .svg:
For each line:
If doesn't contain `\bxmlns\b`:
For each link, `\bhttp://[^# \t\r\n]*(?:\w|/)`:
If both the HTTP and HTTPS versions
return 200 OK and serve the same content:
Replace HTTP with HTTPS.

Signed-off-by: Alexander A. Klimov <grandmaster@al2klimov.de>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: Remove superfluous of_node assignments

If a driver does not assign an of_node to a IIO device to IIO core will
automatically assign the of_node of the parent device. This automatic

iio: Remove superfluous of_node assignments

If a driver does not assign an of_node to a IIO device to IIO core will
automatically assign the of_node of the parent device. This automatic
assignment is done in the iio_device_register() function.

There is a fair amount of drivers that currently manually assign the
of_node of the IIO device. All but 4 of them can make use of the automatic
assignment though.

The exceptions are:
* mxs-lradc-adc: Which uses the of_node of the parent of the parent.
* stm32-dfsdm-adc, stm32-adc and stm32-dac: Which reference the of_node
assigned to the IIO device before iio_device_register() is called.

All other drivers are updated to use automatic assignment. This reduces
the amount of boilerplate code involved in setting up the IIO device.

The patch has mostly been auto-generated with the following semantic patch

// <smpl>
@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(&parent, ...)
...
-indio_dev->dev.of_node = parent.of_node;

@exists@
expression indio_dev;
expression parent;
@@
indio_dev = \(devm_iio_device_alloc\|iio_device_alloc\)(parent, ...)
...
-indio_dev->dev.of_node = parent->of_node;
// </smpl>

Signed-off-by: Lars-Peter Clausen <lars@metafoo.de>
Reviewed-by: Andy Shevchenko <andy.shevchenko@gmail.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->

iio: remove explicit IIO device parent assignment

This patch applies the semantic patch:
@@
expression I, P, SP;
@@
I = devm_iio_device_alloc(P, SP);
...
- I->dev.parent = P;

It updates 302 files and does 307 deletions.
This semantic patch also removes some comments like
'/* Establish that the iio_dev is a child of the i2c device */'

But this is is only done in case where the block is left empty.

The patch does not seem to cover all cases. It looks like in some cases a
different variable is used in some cases to assign the parent, but it
points to the same reference.
In other cases, the block covered by ... may be just too big to be covered
by the semantic patch.

However, this looks pretty good as well, as it does cover a big bulk of the
drivers that should remove the parent assignment.

Signed-off-by: Alexandru Ardelean <alexandru.ardelean@analog.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...

iio: pressure: Add driver for DLH pressure sensors

All Sensors DLH is series of low voltage digital pressure sensors.
Additionally to pressure value sensors deliver a temperature value.

iio: pressure: Add driver for DLH pressure sensors

All Sensors DLH is series of low voltage digital pressure sensors.
Additionally to pressure value sensors deliver a temperature value.
Sensors can be accessed over I2C and SPI, this driver supports
only I2C access.

Signed-off-by: Tomislav Denis <tomislav.denis@avl.com>
Signed-off-by: Jonathan Cameron <Jonathan.Cameron@huawei.com>

show more ...