i2c: algo: pca: Reapply i2c bus settings after reset

If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
co

i2c: algo: pca: Reapply i2c bus settings after reset

If something goes wrong (such as the SCL being stuck low) then we need
to reset the PCA chip. The issue with this is that on reset we lose all
config settings and the chip ends up in a disabled state which results
in a lock up/high CPU usage. We need to re-apply any configuration that
had previously been set and re-enable the chip.

Signed-off-by: Evan Nimmo <evan.nimmo@alliedtelesis.co.nz>
Reviewed-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

show more ...

i2c: Use separate MODULE_AUTHOR() statements for multiple authors

Modules with multiple authors should use multiple MODULE_AUTHOR()
statements according to comment in include/linux/module.h.

Split

i2c: Use separate MODULE_AUTHOR() statements for multiple authors

Modules with multiple authors should use multiple MODULE_AUTHOR()
statements according to comment in include/linux/module.h.

Split the i2c modules with multiple authors to use multiple
MODULE_AUTHOR() statements.

Signed-off-by: Jarkko Nikula <jarkko.nikula@linux.intel.com>
Reviewed-by: Jean Delvare <jdelvare@suse.de>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

show more ...

i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665

The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indicati

i2c: algo-pca: Add 0x78 as SCL stuck low status for PCA9665

The PCA9665 datasheet says that I2CSTA = 78h indicates that SCL is stuck
low, this differs to the PCA9564 which uses 90h for this indication.
Treat either 0x78 or 0x90 as an indication that the SCL line is stuck.

Based on looking through the PCA9564 and PCA9665 datasheets this should
be safe for both chips. The PCA9564 should not return 0x78 for any valid
state and the PCA9665 should not return 0x90.

Fixes: eff9ec95efaa ("i2c-algo-pca: Add PCA9665 support")
Signed-off-by: Chris Packham <chris.packham@alliedtelesis.co.nz>
Reviewed-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@kernel.org>

show more ...

i2c: algo-pca: update contact email

The 'pengutronix' address is defunct for years. Use the proper contact
address.

Signed-off-by: Wolfram Sang <wsa@kernel.org>

i2c: algo: Use generic definitions for bus frequencies

Since we have generic definitions for bus frequencies, let's use them.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Sign

i2c: algo: Use generic definitions for bus frequencies

Since we have generic definitions for bus frequencies, let's use them.

Signed-off-by: Andy Shevchenko <andriy.shevchenko@linux.intel.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

show more ...

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157

Based on 3 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of th

treewide: Replace GPLv2 boilerplate/reference with SPDX - rule 157

Based on 3 normalized pattern(s):

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version this program is distributed in the
hope that it will be useful but without any warranty without even
the implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [kishon] [vijay] [abraham]
[i] [kishon]@[ti] [com] this program is distributed in the hope that
it will be useful but without any warranty without even the implied
warranty of merchantability or fitness for a particular purpose see
the gnu general public license for more details

this program is free software you can redistribute it and or modify
it under the terms of the gnu general public license as published by
the free software foundation either version 2 of the license or at
your option any later version [author] [graeme] [gregory]
[gg]@[slimlogic] [co] [uk] [author] [kishon] [vijay] [abraham] [i]
[kishon]@[ti] [com] [based] [on] [twl6030]_[usb] [c] [author] [hema]
[hk] [hemahk]@[ti] [com] this program is distributed in the hope
that it will be useful but without any warranty without even the
implied warranty of merchantability or fitness for a particular
purpose see the gnu general public license for more details

extracted by the scancode license scanner the SPDX license identifier

GPL-2.0-or-later

has been chosen to replace the boilerplate/reference in 1105 file(s).

Signed-off-by: Thomas Gleixner <tglx@linutronix.de>
Reviewed-by: Allison Randal <allison@lohutok.net>
Reviewed-by: Richard Fontana <rfontana@redhat.com>
Reviewed-by: Kate Stewart <kstewart@linuxfoundation.org>
Cc: linux-spdx@vger.kernel.org
Link: https://lkml.kernel.org/r/20190527070033.202006027@linutronix.de
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>

show more ...

i2c: algos: make use of i2c_8bit_addr_from_msg

Because it looks neater.

Signed-off-by: Peter Rosin <peda@axentia.se>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c: algo-pca: fix typo in comment

Signed-off-by: Shailendra Verma <shailendra.capricorn@gmail.com>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

i2c: remove FSF address

We have a central copy of the GPL for that. Some addresses were already
outdated.

Signed-off-by: Wolfram Sang <wsa+renesas@sang-engineering.com>

i2c: delete non-required instances of include <linux/init.h>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left o

i2c: delete non-required instances of include <linux/init.h>

None of these files are actually using any __init type directives
and hence don't need to include <linux/init.h>. Most are just a
left over from __devinit and __cpuinit removal, or simply due to
code getting copied from one driver to the next.

Signed-off-by: Paul Gortmaker <paul.gortmaker@windriver.com>
Acked-by: Jean Delvare <khali@linux-fr.org>
Signed-off-by: Wolfram Sang <wsa@the-dreams.de>

show more ...

i2c: algo: pca: Fix chip reset function for PCA9665

The parameter passed to pca9665_reset is adap->data (which is bus driver
specific), not i2c_algp_pca_data *adap. pca9665_reset expects it to be
i2

i2c: algo: pca: Fix chip reset function for PCA9665

The parameter passed to pca9665_reset is adap->data (which is bus driver
specific), not i2c_algp_pca_data *adap. pca9665_reset expects it to be
i2c_algp_pca_data *adap. All other wrappers from the algo call back to
the bus driver, which knows to handle its custom data. Only pca9665_reset
resides inside the algorithm code and does not know how to handle a custom
data structure. This can result in a kernel crash.

Fix by re-factoring pca_reset() from a macro to a function handling chip
specific code, and only call adap->reset_chip() if the chip is not PCA9665.

Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

show more ...

i2c: algo: pca: Fix mode selection for PCA9665

The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequenc

i2c: algo: pca: Fix mode selection for PCA9665

The code currently always selects turbo mode for PCA9665, no matter which
clock frequency is configured. This is because it compares the clock frequency
against constants reflecting (boundary / 100). Compare against real boundary
frequencies to fix the problem.

Signed-off-by: Thomas Kavanagh <tkavanagh@juniper.net>
Signed-off-by: Guenter Roeck <groeck@juniper.net>
Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>

show more ...

i2c: Update the FSF address

Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-algo-pca: Return standard fault codes

Adjust i2c-algo-pca to return fault codes compliant with
Documentation/i2c/fault-codes, rather than the undocumented and
vague -EREMOTEIO.

Signed-off-by: J

i2c-algo-pca: Return standard fault codes

Adjust i2c-algo-pca to return fault codes compliant with
Documentation/i2c/fault-codes, rather than the undocumented and
vague -EREMOTEIO.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Cc: Wolfram Sang <w.sang@pengutronix.de>

show more ...

Fix common misspellings

Fixes generated by 'codespell' and manually reviewed.

Signed-off-by: Lucas De Marchi <lucas.demarchi@profusion.mobi>

i2c-algo-pca: Fix coding style issues

Fix up some coding style issues. i2c-algo-pca.c has been built
successfully after applying this patch and the binary object is
still exactly the same. Other iss

i2c-algo-pca: Fix coding style issues

Fix up some coding style issues. i2c-algo-pca.c has been built
successfully after applying this patch and the binary object is
still exactly the same. Other issues found by checkpatch.pl were
voluntarily not fixed, either to keep readability, or because of
false positive errors.

Signed-off-by: Farid Hammane <farid.hammane@gmail.com>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

show more ...

i2c-algo-pca: Drop duplicate variable

Thanks to -Wshadow.

Signed-off-by: Jean Delvare <khali@linux-fr.org>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>

i2c-algo-pca: Let PCA9564 recover from unacked data byte (state 0x30)

Currently, the i2c-algo-pca driver does nothing if the chip enters state
0x30 (Data byte in I2CDAT has been transmitted; NOT ACK

i2c-algo-pca: Let PCA9564 recover from unacked data byte (state 0x30)

Currently, the i2c-algo-pca driver does nothing if the chip enters state
0x30 (Data byte in I2CDAT has been transmitted; NOT ACK has been
received). Thus, the i2c bus connected to the controller gets stuck
afterwards.

I have seen this kind of error on a custom board in certain load
situations most probably caused by interference or noise.

A possible reaction is to let the controller generate a STOP condition.
This is documented in the PCA9564 data sheet (2006-09-01) and the same
is done for other NACK states as well.

Further, state 0x38 isn't handled completely, either. Try to do another
START in this case like the data sheet says. As this couldn't be tested,
I've added a comment to try to reset the chip if the START doesn't help
as suggested by Wolfram Sang.

Signed-off-by: Enrik Berkhan <Enrik.Berkhan@ge.com>
Reviewed-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

show more ...

i2c-algo-pca: Fix use of uninitialized variable in debug message

A recent change broke debugging of pca_xfer(), fix it.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean De

i2c-algo-pca: Fix use of uninitialized variable in debug message

A recent change broke debugging of pca_xfer(), fix it.

Reported-by: Geert Uytterhoeven <geert@linux-m68k.org>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Acked-by: Wolfram Sang <w.sang@pengutronix.de>

show more ...

i2c-algo-pca: Use timeout for checking the state machine

We now timeout also if the state machine does not change within the
given time. For that, the driver-specific completion-functions are
extend

i2c-algo-pca: Use timeout for checking the state machine

We now timeout also if the state machine does not change within the
given time. For that, the driver-specific completion-functions are
extended to return true or false depending on the timeout. This then
gets checked in the algorithm.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

show more ...

i2c-algo-pca: Rework waiting for a free bus

Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.

Signed-off-by: Wolfram Sang <w.sang@pengutron

i2c-algo-pca: Rework waiting for a free bus

Waiting for a free bus now accepts the timeout value in jiffies and does
proper checking using time_before.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

show more ...

i2c-algo-pca: Add PCA9665 support

Add support for the PCA9665 I2C controller.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c: Adapt debug macros for KERN_* constants

According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the changes to the debu

i2c: Adapt debug macros for KERN_* constants

According to kerneljanitors todo list all printk calls (beginning
a new line) should have an according KERN_* constant.
Those are the changes to the debug macros in the i2c subsystem
to meet this requirement. Also changing no-debug statements
to raw printks again.

Signed-off-by: Frank Seidel <frank@f-seidel.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>
Tested-by: Wolfram Sang <w.sang@pengutronix.de>

show more ...

i2c-pca-algo: Fix error code

Give a more concrete error code, when the bus is not idle.

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

i2c-algo-pca: Extend for future drivers

The separation between algorithm and adapter was unsharp at places. This was
partly hidden by the fact, that the ISA-driver allowed just one instance and
had

i2c-algo-pca: Extend for future drivers

The separation between algorithm and adapter was unsharp at places. This was
partly hidden by the fact, that the ISA-driver allowed just one instance and
had all private data in static variables. This patch makes neccessary
preparations to add a platform driver on top of the algorithm, while still
supporting ISA. Note: Due to lack of hardware, the ISA-driver could not be
tested except that it builds.

Concerning the core struct i2c_algo_pca_data:

- A private data field was added, all hardware dependant data may go here.
Similar to other algorithms, now a pointer to this data is passed to the
adapter's functions. In order to make as less changes as possible to the
ISA-driver, it leaves the private data empty and still only uses its static
variables.

- A "reset_chip" function pointer was added; such a functionality must come
from the adapter, not the algorithm.

- use a variable "i2c_clock" instead of a function pointer "get_clock",
allowing for write access to a default in case a wrong value was supplied.

In the algorithm-file:

- move "i2c-pca-algo.h" into "linux/i2c-algo-pca.h"
- now using per_instance timeout values (i2c_adap->timeout)
- error messages specify the device, not only the driver name
- restructure initialization to easily support "i2c_add_numbered_adapter"
- drop "retries" and "own" (i2c address) as they were unused

(The state-machine for I2C-communication was not touched.)

In the ISA-driver:

- adapt to new algorithm

Signed-off-by: Wolfram Sang <w.sang@pengutronix.de>
Signed-off-by: Jean Delvare <khali@linux-fr.org>

show more ...