drm/msm/dsi: More properly handle errors in regards to dsi_mgr_bridge_power_on()

In commit 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to modeset
time") the error handling with regards to dsi_

drm/msm/dsi: More properly handle errors in regards to dsi_mgr_bridge_power_on()

In commit 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to modeset
time") the error handling with regards to dsi_mgr_bridge_power_on()
got a bit worse. Specifically if we failed to power the bridge on then
nothing would really notice. The modeset function couldn't return an
error and thus we'd blindly go forward and try to do the pre-enable.

In commit ec7981e6c614 ("drm/msm/dsi: don't powerup at modeset time
for parade-ps8640") we added a special case to move the powerup back
to pre-enable time for ps8640. When we did that, we didn't try to
recover the old/better error handling just for ps8640.

In the patch ("drm/msm/dsi: Stop unconditionally powering up DSI hosts
at modeset") we've now moved the powering up back to exclusively being
during pre-enable. That means we can add the better error handling
back in, so let's do it. To do so we'll add a new function
dsi_mgr_bridge_power_off() that's matches how errors were handled
prior to commit 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to
modeset time").

NOTE: Now that we have dsi_mgr_bridge_power_off(), it feels as if we
should be calling it in dsi_mgr_bridge_post_disable(). That would make
some sense, but doing so would change the current behavior and thus
should be a separate patch. Specifically:
* dsi_mgr_bridge_post_disable() always calls dsi_mgr_phy_disable()
even in the slave-DSI case of bonded DSI. We'd need to add special
handling for this if it's truly needed.
* dsi_mgr_bridge_post_disable() calls msm_dsi_phy_pll_save_state()
midway through the poweroff.
* dsi_mgr_bridge_post_disable() has a different order of some of the
poweroffs / IRQ disables.
For now we'll leave dsi_mgr_bridge_post_disable() alone.

Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/521059/
Link: https://lore.kernel.org/r/20230131141756.RFT.v2.3.I3c87b53c4ab61a7d5e05f601a4eb44c7e3809a01@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm/dsi: Stop unconditionally powering up DSI hosts at modeset

In commit 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to modeset
time"), we moved powering up DSI hosts to modeset time. This

drm/msm/dsi: Stop unconditionally powering up DSI hosts at modeset

In commit 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to modeset
time"), we moved powering up DSI hosts to modeset time. This wasn't
because it was an elegant design, but there were no better options.

That commit actually ended up breaking ps8640, and thus was born
commit ec7981e6c614 ("drm/msm/dsi: don't powerup at modeset time for
parade-ps8640") as a temporary hack to un-break ps8640 by moving it to
the old way of doing things. It turns out that ps8640 _really_ doesn't
like its pre_enable() function to be called after
dsi_mgr_bridge_power_on(). Specifically (from experimentation, not
because I have any inside knowledge), it looks like the assertion of
"RST#" in the ps8640 runtime resume handler seems like it's not
allowed to happen after dsi_mgr_bridge_power_on()

Recently, Dave Stevenson's series landed allowing bridges some control
over pre_enable ordering. The meaty commit for our purposes is
commit 4fb912e5e190 ("drm/bridge: Introduce pre_enable_prev_first to
alter bridge init order"). As documented by that series, if a bridge
doesn't set "pre_enable_prev_first" then we should use the old ordering.

Now that we have the commit ("drm/bridge: tc358762: Set
pre_enable_prev_first") we can go back to the old ordering, which also
allows us to remove the ps8640 special case.

One last note is that even without reverting commit 7d8e9a90509f
("drm/msm/dsi: move DSI host powerup to modeset time"), if you _just_
revert the ps8640 special case and try it out then it doesn't seem to
fail anymore. I spent time bisecting / debugging this and it turns out
to be mostly luck, so we still want this patch to make sure it's
solid. Specifically the reason it sorta works these days is because
we implemented wait_hpd_asserted() in ps8640 now, plus the magic of
"pm_runtime" autosuspend. The fact that we have wait_hpd_asserted()
implemented means that we actually power the bridge chip up just a wee
bit earlier and then the bridge happens to stay on because of
autosuspend and thus ends up powered before dsi_mgr_bridge_power_on().

Cc: Dave Stevenson <dave.stevenson@raspberrypi.com>
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/521058/
Link: https://lore.kernel.org/r/20230131141756.RFT.v2.2.I4cfeab9d0e07e98ead23dd0736ab4461e6c69002@changeid
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm/dsi: properly handle the case of empty OPP table in dsi_mgr_bridge_mode_valid

It was left unnoticed during the review that even if there is no OPP
table in device tree, one will be created b

drm/msm/dsi: properly handle the case of empty OPP table in dsi_mgr_bridge_mode_valid

It was left unnoticed during the review that even if there is no OPP
table in device tree, one will be created by a call to the function
devm_pm_opp_set_clkname(). This leads to dsi_mgr_bridge_mode_valid()
rejecting all modes if DT contains no OPP table for the DSI host.

Rework dsi_mgr_bridge_mode_valid() to handle this case by actually
checking that the table is populated with frequency entries before
returning an error.

Fixes: 8328041b8c82 ("drm/msm/dsi: implement opp table based check for dsi_mgr_bridge_mode_valid()")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/520076/
Link: https://lore.kernel.org/r/20230124203600.3488766-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm/dsi: implement opp table based check for dsi_mgr_bridge_mode_valid()

Currently there is no protection against a user trying to set
an unsupported mode on DSI. Implement a check based on the

drm/msm/dsi: implement opp table based check for dsi_mgr_bridge_mode_valid()

Currently there is no protection against a user trying to set
an unsupported mode on DSI. Implement a check based on the opp
table whether the byte clock for the mode can be supported by
validating whether an opp table entry exists.

For devices which have not added opp table support yet, skip
this check otherwise it will break bootup on those devices.

changes in v3:
- make the comment shorter
- handle all errors except ENODEV

Closes: https://gitlab.freedesktop.org/drm/msm/-/issues/15
Reported-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/518008/
Link: https://lore.kernel.org/r/20230112001600.12791-2-quic_abhinavk@quicinc.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm/dsi: switch to DRM_PANEL_BRIDGE

Currently the DSI driver has two separate paths: one if the next device
in a chain is a bridge and another one if the panel is connected
directly to the DSI h

drm/msm/dsi: switch to DRM_PANEL_BRIDGE

Currently the DSI driver has two separate paths: one if the next device
in a chain is a bridge and another one if the panel is connected
directly to the DSI host. Simplify the code path by using panel-bridge
driver (already selected in Kconfig) and dropping support for
handling the panel directly.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/493608/
Link: https://lore.kernel.org/r/20220712132258.671263-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: Remove the unneeded result variable

Return the value msm_dsi_phy_enable() directly instead of storing it in
another redundant variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Sign

drm/msm/dsi: Remove the unneeded result variable

Return the value msm_dsi_phy_enable() directly instead of storing it in
another redundant variable.

Reported-by: Zeal Robot <zealci@zte.com.cn>
Signed-off-by: ye xingchen <ye.xingchen@zte.com.cn>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/499621/
Link: https://lore.kernel.org/r/20220826072821.253150-1-ye.xingchen@zte.com.cn
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: don't powerup at modeset time for parade-ps8640

Commit 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to modeset
time") caused sc7180 Chromebooks that use the parade-ps8640 bridge
ch

drm/msm/dsi: don't powerup at modeset time for parade-ps8640

Commit 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to modeset
time") caused sc7180 Chromebooks that use the parade-ps8640 bridge
chip to fail to turn the display back on after it turns off.

Unfortunately, it doesn't look easy to fix the parade-ps8640 driver to
handle the new power sequence. The Linux driver has almost nothing in
it and most of the logic for this bridge chip is in black-box firmware
that the bridge chip uses.

Also unfortunately, reverting the patch will break "tc358762".

The long term solution here is probably Dave Stevenson's series [1]
that would give more flexibility. However, that is likely not a quick
fix.

For the short term, we'll look at the compatible of the next bridge in
the chain and go back to the old way for the Parade PS8640 bridge
chip. If it's found that other bridge chips also need this workaround
then we can add them to the list or consider inverting the
condition. However, the hope is that the framework will not take too
much longer to land and we won't have to add anything other than
ps8640 here.

[1] https://lore.kernel.org/r/cover.1646406653.git.dave.stevenson@raspberrypi.com

Fixes: 7d8e9a90509f ("drm/msm/dsi: move DSI host powerup to modeset time")
Suggested-by: Rob Clark <robdclark@gmail.com>
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20220513131504.v5.1.Ia196e35ad985059e77b038a41662faae9e26f411@changeid
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: add mode valid callback for dsi_mgr

Add a mode valid callback for dsi_mgr for checking mode being valid in
case of DSC. For DSC the height and width needs to be multiple of slice,
so we

drm/msm/dsi: add mode valid callback for dsi_mgr

Add a mode valid callback for dsi_mgr for checking mode being valid in
case of DSC. For DSC the height and width needs to be multiple of slice,
so we check that here

Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Patchwork: https://patchwork.freedesktop.org/patch/480930/
Link: https://lore.kernel.org/r/20220406094031.1027376-13-vkoul@kernel.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm: properly add and remove internal bridges

Add calls to drm_bridge_add()/drm_bridge_remove() DRM bridges created by
the driver. This fixes the following warning.

WARNING: CPU: 0 PID: 1 at ke

drm/msm: properly add and remove internal bridges

Add calls to drm_bridge_add()/drm_bridge_remove() DRM bridges created by
the driver. This fixes the following warning.

WARNING: CPU: 0 PID: 1 at kernel/locking/mutex.c:579 __mutex_lock+0x840/0x9f4
DEBUG_LOCKS_WARN_ON(lock->magic != lock)
Modules linked in:
CPU: 0 PID: 1 Comm: swapper/0 Not tainted 5.18.0-rc1-00002-g3054695a0d27-dirty #55
Hardware name: Generic DT based system
unwind_backtrace from show_stack+0x10/0x14
show_stack from dump_stack_lvl+0x58/0x70
dump_stack_lvl from __warn+0xc8/0x1e8
__warn from warn_slowpath_fmt+0x78/0xa8
warn_slowpath_fmt from __mutex_lock+0x840/0x9f4
__mutex_lock from mutex_lock_nested+0x1c/0x24
mutex_lock_nested from drm_bridge_hpd_enable+0x2c/0x84
drm_bridge_hpd_enable from msm_hdmi_modeset_init+0xc0/0x21c
msm_hdmi_modeset_init from mdp4_kms_init+0x53c/0x90c
mdp4_kms_init from msm_drm_bind+0x514/0x698
msm_drm_bind from try_to_bring_up_aggregate_device+0x160/0x1bc
try_to_bring_up_aggregate_device from component_master_add_with_match+0xc4/0xf8
component_master_add_with_match from msm_pdev_probe+0x274/0x350
msm_pdev_probe from platform_probe+0x5c/0xbc
platform_probe from really_probe.part.0+0x9c/0x290
really_probe.part.0 from __driver_probe_device+0xa8/0x13c
__driver_probe_device from driver_probe_device+0x34/0x10c
driver_probe_device from __driver_attach+0xbc/0x178
__driver_attach from bus_for_each_dev+0x74/0xc0
bus_for_each_dev from bus_add_driver+0x160/0x1e4
bus_add_driver from driver_register+0x88/0x118
driver_register from do_one_initcall+0x6c/0x334
do_one_initcall from kernel_init_freeable+0x1bc/0x220
kernel_init_freeable from kernel_init+0x18/0x12c
kernel_init from ret_from_fork+0x14/0x2c

Fixes: 3d3f8b1f8b62 ("drm/bridge: make bridge registration independent of drm flow")
Reported-by: kernel test robot <lkp@intel.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Patchwork: https://patchwork.freedesktop.org/patch/481778/
Link: https://lore.kernel.org/r/20220411234953.2425280-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()

The member 'msm_dsi->connector' isn't assigned until
msm_dsi_manager_connector_init() returns (see msm_dsi_modeset_init() and

drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()

The member 'msm_dsi->connector' isn't assigned until
msm_dsi_manager_connector_init() returns (see msm_dsi_modeset_init() and
how it assigns the return value). Therefore this pointer is going to be
NULL here. Let's use 'connector' which is what was intended.

Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 6d5e78406991 ("drm/msm/dsi: Move dsi panel init into modeset init path")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/478693/
Link: https://lore.kernel.org/r/20220318000731.2823718-1-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: move DSI host powerup to modeset time

The DSI subsystem does not fully fall into the pre-enable/enable system
of callbacks, since typically DSI device bridge drivers expect to be
able t

drm/msm/dsi: move DSI host powerup to modeset time

The DSI subsystem does not fully fall into the pre-enable/enable system
of callbacks, since typically DSI device bridge drivers expect to be
able to communicate with DSI devices at the pre-enable() callback. The
reason is that for some DSI hosts enabling the video stream would
prevent other drivers from sending DSI commands. For example see the
panel-bridge driver, which does drm_panel_prepare() from the
pre_enable() callback (which would be called before our pre_enable()
callback, resulting in panel preparation failures as the link is not yet
ready).

Therewere several attempts to solve this issue, but currently the best
approach is to power up the DSI link from the mode_set() callback,
allowing next bridge/panel to use DSI transfers in the pre_enable()
time. Follow this approach.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211207222901.988484-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm: reduce usage of round_pixclk callback

The round_pixclk() callback returns different rate only on MDP4 in HDMI
(DTV) case. Stop using this callback in other cases to simplify
mode_valid call

drm/msm: reduce usage of round_pixclk callback

The round_pixclk() callback returns different rate only on MDP4 in HDMI
(DTV) case. Stop using this callback in other cases to simplify
mode_valid callbacks.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20220106070656.482882-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>

show more ...

drm/msm/dsi: fix initialization in the bonded DSI case

Commit 739b4e7756d3 ("drm/msm/dsi: Fix an error code in
msm_dsi_modeset_init()") changed msm_dsi_modeset_init() to return an
error code in case

drm/msm/dsi: fix initialization in the bonded DSI case

Commit 739b4e7756d3 ("drm/msm/dsi: Fix an error code in
msm_dsi_modeset_init()") changed msm_dsi_modeset_init() to return an
error code in case msm_dsi_manager_validate_current_config() returns
false. However this is not an error case, but a slave DSI of the bonded
DSI link. In this case msm_dsi_modeset_init() should return 0, but just
skip connector and bridge initialization.

To reduce possible confusion, drop the
msm_dsi_manager_validate_current_config() function, and specif 'bonded
&& !master' condition directly in the msm_dsi_modeset_init().

Fixes: 739b4e7756d3 ("drm/msm/dsi: Fix an error code in msm_dsi_modeset_init()")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211125180114.561278-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: stop setting clock parents manually

There is no reason to set clock parents manually, use device tree to
assign DSI/display clock parents to DSI PHY clocks. Dropping this manual
setup a

drm/msm/dsi: stop setting clock parents manually

There is no reason to set clock parents manually, use device tree to
assign DSI/display clock parents to DSI PHY clocks. Dropping this manual
setup allows us to drop repeating code and to move registration of hw
clock providers to generic place.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211006204828.1218225-2-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: untangle cphy setting from the src pll setting

Move DPHY/CPHY setting from msm_dsi_host_set_src_pll() to new function
msm_dsi_host_set_phy_mode().

Signed-off-by: Dmitry Baryshkov <dmit

drm/msm/dsi: untangle cphy setting from the src pll setting

Move DPHY/CPHY setting from msm_dsi_host_set_src_pll() to new function
msm_dsi_host_set_phy_mode().

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211006204828.1218225-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: Adjust probe order

Switch to the documented order dsi-host vs bridge probe.

Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested

drm/msm/dsi: Adjust probe order

Switch to the documented order dsi-host vs bridge probe.

Tested-by: Amit Pundir <amit.pundir@linaro.org>
Tested-by: Caleb Connolly <caleb.connolly@linaro.org>
Tested-by: John Stultz <john.stultz@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20211025151536.1048186-22-maxime@cerno.tech

show more ...

drm/msm/dsi: do not enable irq handler before powering up the host

The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the

drm/msm/dsi: do not enable irq handler before powering up the host

The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the
interrupt line before the driver sets up the DSI host to the known
state.

Move the request_irq into msm_dsi_host_init and pass IRQF_NO_AUTOEN to
it. Call enable/disable_irq after msm_dsi_host_power_on/_off()
functions, so that we can be sure that the interrupt is delivered when
the host is in the known state.

It is not possible to defer the interrupt enablement to a later point,
because drm_panel_prepare might need to communicate with the panel over
the DSI link and that requires working interrupt.

Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211002010830.647416-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: Support NO_CONNECTOR bridges

For now, since we have a mix of bridges which support this flag, which
which do *not* support this flag, or work both ways, try it once with
NO_CONNECTOR an

drm/msm/dsi: Support NO_CONNECTOR bridges

For now, since we have a mix of bridges which support this flag, which
which do *not* support this flag, or work both ways, try it once with
NO_CONNECTOR and then fall back to the old way if that doesn't work.
Eventually we can drop the fallback path.

v2: Add missing drm_connector_attach_encoder() so display actually comes
up when the bridge properly handles the NO_CONNECTOR flag

Signed-off-by: Rob Clark <robdclark@chromium.org>
Reviewed-by: Laurent Pinchart <laurent.pinchart@ideasonboard.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210920225801.227211-2-robdclark@gmail.com
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()

[ Upstream commit 47b7de6b88b962ef339a2427a023d2a23d161654 ]

The member 'msm_dsi->connector' isn't assigned until
msm_dsi_man

drm/msm/dsi: Use connector directly in msm_dsi_manager_connector_init()

[ Upstream commit 47b7de6b88b962ef339a2427a023d2a23d161654 ]

The member 'msm_dsi->connector' isn't assigned until
msm_dsi_manager_connector_init() returns (see msm_dsi_modeset_init() and
how it assigns the return value). Therefore this pointer is going to be
NULL here. Let's use 'connector' which is what was intended.

Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: Sean Paul <seanpaul@chromium.org>
Fixes: 6d5e78406991 ("drm/msm/dsi: Move dsi panel init into modeset init path")
Signed-off-by: Stephen Boyd <swboyd@chromium.org>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Patchwork: https://patchwork.freedesktop.org/patch/478693/
Link: https://lore.kernel.org/r/20220318000731.2823718-1-swboyd@chromium.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

drm/msm/dsi: fix initialization in the bonded DSI case

[ Upstream commit 92cb1bedde9dba78d802fe2510949743a2581aed ]

Commit 739b4e7756d3 ("drm/msm/dsi: Fix an error code in
msm_dsi_modeset_init()")

drm/msm/dsi: fix initialization in the bonded DSI case

[ Upstream commit 92cb1bedde9dba78d802fe2510949743a2581aed ]

Commit 739b4e7756d3 ("drm/msm/dsi: Fix an error code in
msm_dsi_modeset_init()") changed msm_dsi_modeset_init() to return an
error code in case msm_dsi_manager_validate_current_config() returns
false. However this is not an error case, but a slave DSI of the bonded
DSI link. In this case msm_dsi_modeset_init() should return 0, but just
skip connector and bridge initialization.

To reduce possible confusion, drop the
msm_dsi_manager_validate_current_config() function, and specif 'bonded
&& !master' condition directly in the msm_dsi_modeset_init().

Fixes: 739b4e7756d3 ("drm/msm/dsi: Fix an error code in msm_dsi_modeset_init()")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Link: https://lore.kernel.org/r/20211125180114.561278-1-dmitry.baryshkov@linaro.org
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

drm/msm/dsi: do not enable irq handler before powering up the host

[ Upstream commit bf94ec093d05e3ed3142d9291b876eeb9997ba5c ]

The DSI host might be left in some state by the bootloader. If this
s

drm/msm/dsi: do not enable irq handler before powering up the host

[ Upstream commit bf94ec093d05e3ed3142d9291b876eeb9997ba5c ]

The DSI host might be left in some state by the bootloader. If this
state generates an IRQ, it might hang the system by holding the
interrupt line before the driver sets up the DSI host to the known
state.

Move the request_irq into msm_dsi_host_init and pass IRQF_NO_AUTOEN to
it. Call enable/disable_irq after msm_dsi_host_power_on/_off()
functions, so that we can be sure that the interrupt is delivered when
the host is in the known state.

It is not possible to defer the interrupt enablement to a later point,
because drm_panel_prepare might need to communicate with the panel over
the DSI link and that requires working interrupt.

Fixes: a689554ba6ed ("drm/msm: Initial add DSI connector support")
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20211002010830.647416-1-dmitry.baryshkov@linaro.org
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>
Signed-off-by: Sasha Levin <sashal@kernel.org>

show more ...

drm/msm/dsi: add continuous clock support for 7nm PHY

Unlike previous generations, 7nm PHYs are required to collaborate with
the host for continuos clock mode. Add changes neccessary to enable
conti

drm/msm/dsi: add continuous clock support for 7nm PHY

Unlike previous generations, 7nm PHYs are required to collaborate with
the host for continuos clock mode. Add changes neccessary to enable
continuous clock mode in the 7nm DSI PHYs.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20210805170817.3337665-1-dmitry.baryshkov@linaro.org
[Fix merge conflict, and $description typo]
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: stop calling set_encoder_mode callback

None of the display drivers now implement set_encoder_mode callback.
Stop calling it from the modeset init code.

Signed-off-by: Dmitry Baryshkov

drm/msm/dsi: stop calling set_encoder_mode callback

None of the display drivers now implement set_encoder_mode callback.
Stop calling it from the modeset init code.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210717124016.316020-7-dmitry.baryshkov@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: add three helper functions

Add three helper functions to be used by display drivers for setting up
encoders.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by:

drm/msm/dsi: add three helper functions

Add three helper functions to be used by display drivers for setting up
encoders.

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210717124016.316020-3-dmitry.baryshkov@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...

drm/msm/dsi: rename dual DSI to bonded DSI

We are preparing to support two independent DSI hosts in the DSI/DPU
code. To remove possible confusion (as both configurations can be
referenced as dual D

drm/msm/dsi: rename dual DSI to bonded DSI

We are preparing to support two independent DSI hosts in the DSI/DPU
code. To remove possible confusion (as both configurations can be
referenced as dual DSI) let's rename old "dual DSI" (two DSI hosts
driving single device, with clocks being locked) to "bonded DSI".

Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Abhinav Kumar <abhinavk@codeaurora.org>
Link: https://lore.kernel.org/r/20210717124016.316020-2-dmitry.baryshkov@linaro.org
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
[DB: add one extra hunk added by one previous patches]
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Rob Clark <robdclark@chromium.org>

show more ...