|
Revision tags: v6.6.27, v6.6.26, v6.6.25, v6.6.24, v6.6.23, v6.6.16 |
|
| #
5c1dc516 |
| 02-Feb-2024 |
Shradha Gupta <shradhagupta@linux.microsoft.com> |
drm: Check polling initialized before enabling in drm_helper_probe_single_connector_modes
commit 048a36d8a6085bbd8ab9e5794b713b92ac986450 upstream.
In function drm_helper_probe_single_connector_mod
drm: Check polling initialized before enabling in drm_helper_probe_single_connector_modes
commit 048a36d8a6085bbd8ab9e5794b713b92ac986450 upstream.
In function drm_helper_probe_single_connector_modes() when we enable
polling again, if it is already uninitialized, a warning is reported.
This patch fixes the warning message by checking if poll is initialized
before enabling it.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401191128.db8423f1-oliver.sang@intel.com
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1706856224-9725-1-git-send-email-shradhagupta@linux.microsoft.com
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| #
3d1b47e3 |
| 02-Feb-2024 |
Shradha Gupta <shradhagupta@linux.microsoft.com> |
drm: Check output polling initialized before disabling
[ Upstream commit 5abffb66d12bcac84bf7b66389c571b8bb6e82bd ]
In drm_kms_helper_poll_disable() check if output polling
support is initialized b
drm: Check output polling initialized before disabling
[ Upstream commit 5abffb66d12bcac84bf7b66389c571b8bb6e82bd ]
In drm_kms_helper_poll_disable() check if output polling
support is initialized before disabling polling. If not flag
this as a warning.
Additionally in drm_mode_config_helper_suspend() and
drm_mode_config_helper_resume() calls, that re the callers of these
functions, avoid invoking them if polling is not initialized.
For drivers like hyperv-drm, that do not initialize connector
polling, if suspend is called without this check, it leads to
suspend failure with following stack
[ 770.719392] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 770.720592] printk: Suspending console(s) (use no_console_suspend to debug)
[ 770.948823] ------------[ cut here ]------------
[ 770.948824] WARNING: CPU: 1 PID: 17197 at kernel/workqueue.c:3162 __flush_work.isra.0+0x212/0x230
[ 770.948831] Modules linked in: rfkill nft_counter xt_conntrack xt_owner udf nft_compat crc_itu_t nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables nfnetlink vfat fat mlx5_ib ib_uverbs ib_core mlx5_core intel_rapl_msr intel_rapl_common kvm_amd ccp mlxfw kvm psample hyperv_drm tls drm_shmem_helper drm_kms_helper irqbypass pcspkr syscopyarea sysfillrect sysimgblt hv_balloon hv_utils joydev drm fuse xfs libcrc32c pci_hyperv pci_hyperv_intf sr_mod sd_mod cdrom t10_pi sg hv_storvsc scsi_transport_fc hv_netvsc serio_raw hyperv_keyboard hid_hyperv crct10dif_pclmul crc32_pclmul crc32c_intel hv_vmbus ghash_clmulni_intel dm_mirror dm_region_hash dm_log dm_mod
[ 770.948863] CPU: 1 PID: 17197 Comm: systemd-sleep Not tainted 5.14.0-362.2.1.el9_3.x86_64 #1
[ 770.948865] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 05/09/2022
[ 770.948866] RIP: 0010:__flush_work.isra.0+0x212/0x230
[ 770.948869] Code: 8b 4d 00 4c 8b 45 08 89 ca 48 c1 e9 04 83 e2 08 83 e1 0f 83 ca 02 89 c8 48 0f ba 6d 00 03 e9 25 ff ff ff 0f 0b e9 4e ff ff ff <0f> 0b 45 31 ed e9 44 ff ff ff e8 8f 89 b2 00 66 66 2e 0f 1f 84 00
[ 770.948870] RSP: 0018:ffffaf4ac213fb10 EFLAGS: 00010246
[ 770.948871] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff8c992857
[ 770.948872] RDX: 0000000000000001 RSI: 0000000000000001 RDI: ffff9aad82b00330
[ 770.948873] RBP: ffff9aad82b00330 R08: 0000000000000000 R09: ffff9aad87ee3d10
[ 770.948874] R10: 0000000000000200 R11: 0000000000000000 R12: ffff9aad82b00330
[ 770.948874] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
[ 770.948875] FS: 00007ff1b2f6bb40(0000) GS:ffff9aaf37d00000(0000) knlGS:0000000000000000
[ 770.948878] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 770.948878] CR2: 0000555f345cb666 CR3: 00000001462dc005 CR4: 0000000000370ee0
[ 770.948879] Call Trace:
[ 770.948880] <TASK>
[ 770.948881] ? show_trace_log_lvl+0x1c4/0x2df
[ 770.948884] ? show_trace_log_lvl+0x1c4/0x2df
[ 770.948886] ? __cancel_work_timer+0x103/0x190
[ 770.948887] ? __flush_work.isra.0+0x212/0x230
[ 770.948889] ? __warn+0x81/0x110
[ 770.948891] ? __flush_work.isra.0+0x212/0x230
[ 770.948892] ? report_bug+0x10a/0x140
[ 770.948895] ? handle_bug+0x3c/0x70
[ 770.948898] ? exc_invalid_op+0x14/0x70
[ 770.948899] ? asm_exc_invalid_op+0x16/0x20
[ 770.948903] ? __flush_work.isra.0+0x212/0x230
[ 770.948905] __cancel_work_timer+0x103/0x190
[ 770.948907] ? _raw_spin_unlock_irqrestore+0xa/0x30
[ 770.948910] drm_kms_helper_poll_disable+0x1e/0x40 [drm_kms_helper]
[ 770.948923] drm_mode_config_helper_suspend+0x1c/0x80 [drm_kms_helper]
[ 770.948933] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus]
[ 770.948942] hyperv_vmbus_suspend+0x17/0x40 [hyperv_drm]
[ 770.948944] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus]
[ 770.948951] dpm_run_callback+0x4c/0x140
[ 770.948954] __device_suspend_noirq+0x74/0x220
[ 770.948956] dpm_noirq_suspend_devices+0x148/0x2a0
[ 770.948958] dpm_suspend_end+0x54/0xe0
[ 770.948960] create_image+0x14/0x290
[ 770.948963] hibernation_snapshot+0xd6/0x200
[ 770.948964] hibernate.cold+0x8b/0x1fb
[ 770.948967] state_store+0xcd/0xd0
[ 770.948969] kernfs_fop_write_iter+0x124/0x1b0
[ 770.948973] new_sync_write+0xff/0x190
[ 770.948976] vfs_write+0x1ef/0x280
[ 770.948978] ksys_write+0x5f/0xe0
[ 770.948979] do_syscall_64+0x5c/0x90
[ 770.948981] ? syscall_exit_work+0x103/0x130
[ 770.948983] ? syscall_exit_to_user_mode+0x12/0x30
[ 770.948985] ? do_syscall_64+0x69/0x90
[ 770.948986] ? do_syscall_64+0x69/0x90
[ 770.948987] ? do_user_addr_fault+0x1d6/0x6a0
[ 770.948989] ? do_syscall_64+0x69/0x90
[ 770.948990] ? exc_page_fault+0x62/0x150
[ 770.948992] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 770.948995] RIP: 0033:0x7ff1b293eba7
[ 770.949010] Code: 0b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
[ 770.949011] RSP: 002b:00007ffde3912128 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 770.949012] RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007ff1b293eba7
[ 770.949013] RDX: 0000000000000005 RSI: 00007ffde3912210 RDI: 0000000000000004
[ 770.949014] RBP: 00007ffde3912210 R08: 000055d7dd4c9510 R09: 00007ff1b29b14e0
[ 770.949014] R10: 00007ff1b29b13e0 R11: 0000000000000246 R12: 0000000000000005
[ 770.949015] R13: 000055d7dd4c53e0 R14: 0000000000000005 R15: 00007ff1b29f69e0
[ 770.949016] </TASK>
[ 770.949017] ---[ end trace e6fa0618bfa2f31d ]---
Built-on: Rhel9, Ubuntu22
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1706856208-9617-1-git-send-email-shradhagupta@linux.microsoft.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
|
Revision tags: v6.6.27, v6.6.26, v6.6.25, v6.6.24, v6.6.23, v6.6.16 |
|
| #
5c1dc516 |
| 02-Feb-2024 |
Shradha Gupta <shradhagupta@linux.microsoft.com> |
drm: Check polling initialized before enabling in drm_helper_probe_single_connector_modes
commit 048a36d8a6085bbd8ab9e5794b713b92ac986450 upstream.
In function drm_helper_probe_single_connector_mod
drm: Check polling initialized before enabling in drm_helper_probe_single_connector_modes
commit 048a36d8a6085bbd8ab9e5794b713b92ac986450 upstream.
In function drm_helper_probe_single_connector_modes() when we enable
polling again, if it is already uninitialized, a warning is reported.
This patch fixes the warning message by checking if poll is initialized
before enabling it.
Reported-by: kernel test robot <oliver.sang@intel.com>
Closes: https://lore.kernel.org/oe-lkp/202401191128.db8423f1-oliver.sang@intel.com
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1706856224-9725-1-git-send-email-shradhagupta@linux.microsoft.com
Cc: Holger Hoffstätte <holger@applied-asynchrony.com>
Signed-off-by: Greg Kroah-Hartman <gregkh@linuxfoundation.org>
show more ...
|
| #
3d1b47e3 |
| 02-Feb-2024 |
Shradha Gupta <shradhagupta@linux.microsoft.com> |
drm: Check output polling initialized before disabling
[ Upstream commit 5abffb66d12bcac84bf7b66389c571b8bb6e82bd ]
In drm_kms_helper_poll_disable() check if output polling
support is initialized b
drm: Check output polling initialized before disabling
[ Upstream commit 5abffb66d12bcac84bf7b66389c571b8bb6e82bd ]
In drm_kms_helper_poll_disable() check if output polling
support is initialized before disabling polling. If not flag
this as a warning.
Additionally in drm_mode_config_helper_suspend() and
drm_mode_config_helper_resume() calls, that re the callers of these
functions, avoid invoking them if polling is not initialized.
For drivers like hyperv-drm, that do not initialize connector
polling, if suspend is called without this check, it leads to
suspend failure with following stack
[ 770.719392] Freezing remaining freezable tasks ... (elapsed 0.001 seconds) done.
[ 770.720592] printk: Suspending console(s) (use no_console_suspend to debug)
[ 770.948823] ------------[ cut here ]------------
[ 770.948824] WARNING: CPU: 1 PID: 17197 at kernel/workqueue.c:3162 __flush_work.isra.0+0x212/0x230
[ 770.948831] Modules linked in: rfkill nft_counter xt_conntrack xt_owner udf nft_compat crc_itu_t nft_fib_inet nft_fib_ipv4 nft_fib_ipv6 nft_fib nft_reject_inet nf_reject_ipv4 nf_reject_ipv6 nft_reject nft_ct nft_chain_nat nf_nat nf_conntrack nf_defrag_ipv6 nf_defrag_ipv4 ip_set nf_tables nfnetlink vfat fat mlx5_ib ib_uverbs ib_core mlx5_core intel_rapl_msr intel_rapl_common kvm_amd ccp mlxfw kvm psample hyperv_drm tls drm_shmem_helper drm_kms_helper irqbypass pcspkr syscopyarea sysfillrect sysimgblt hv_balloon hv_utils joydev drm fuse xfs libcrc32c pci_hyperv pci_hyperv_intf sr_mod sd_mod cdrom t10_pi sg hv_storvsc scsi_transport_fc hv_netvsc serio_raw hyperv_keyboard hid_hyperv crct10dif_pclmul crc32_pclmul crc32c_intel hv_vmbus ghash_clmulni_intel dm_mirror dm_region_hash dm_log dm_mod
[ 770.948863] CPU: 1 PID: 17197 Comm: systemd-sleep Not tainted 5.14.0-362.2.1.el9_3.x86_64 #1
[ 770.948865] Hardware name: Microsoft Corporation Virtual Machine/Virtual Machine, BIOS Hyper-V UEFI Release v4.1 05/09/2022
[ 770.948866] RIP: 0010:__flush_work.isra.0+0x212/0x230
[ 770.948869] Code: 8b 4d 00 4c 8b 45 08 89 ca 48 c1 e9 04 83 e2 08 83 e1 0f 83 ca 02 89 c8 48 0f ba 6d 00 03 e9 25 ff ff ff 0f 0b e9 4e ff ff ff <0f> 0b 45 31 ed e9 44 ff ff ff e8 8f 89 b2 00 66 66 2e 0f 1f 84 00
[ 770.948870] RSP: 0018:ffffaf4ac213fb10 EFLAGS: 00010246
[ 770.948871] RAX: 0000000000000000 RBX: 0000000000000000 RCX: ffffffff8c992857
[ 770.948872] RDX: 0000000000000001 RSI: 0000000000000001 RDI: ffff9aad82b00330
[ 770.948873] RBP: ffff9aad82b00330 R08: 0000000000000000 R09: ffff9aad87ee3d10
[ 770.948874] R10: 0000000000000200 R11: 0000000000000000 R12: ffff9aad82b00330
[ 770.948874] R13: 0000000000000001 R14: 0000000000000000 R15: 0000000000000001
[ 770.948875] FS: 00007ff1b2f6bb40(0000) GS:ffff9aaf37d00000(0000) knlGS:0000000000000000
[ 770.948878] CS: 0010 DS: 0000 ES: 0000 CR0: 0000000080050033
[ 770.948878] CR2: 0000555f345cb666 CR3: 00000001462dc005 CR4: 0000000000370ee0
[ 770.948879] Call Trace:
[ 770.948880] <TASK>
[ 770.948881] ? show_trace_log_lvl+0x1c4/0x2df
[ 770.948884] ? show_trace_log_lvl+0x1c4/0x2df
[ 770.948886] ? __cancel_work_timer+0x103/0x190
[ 770.948887] ? __flush_work.isra.0+0x212/0x230
[ 770.948889] ? __warn+0x81/0x110
[ 770.948891] ? __flush_work.isra.0+0x212/0x230
[ 770.948892] ? report_bug+0x10a/0x140
[ 770.948895] ? handle_bug+0x3c/0x70
[ 770.948898] ? exc_invalid_op+0x14/0x70
[ 770.948899] ? asm_exc_invalid_op+0x16/0x20
[ 770.948903] ? __flush_work.isra.0+0x212/0x230
[ 770.948905] __cancel_work_timer+0x103/0x190
[ 770.948907] ? _raw_spin_unlock_irqrestore+0xa/0x30
[ 770.948910] drm_kms_helper_poll_disable+0x1e/0x40 [drm_kms_helper]
[ 770.948923] drm_mode_config_helper_suspend+0x1c/0x80 [drm_kms_helper]
[ 770.948933] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus]
[ 770.948942] hyperv_vmbus_suspend+0x17/0x40 [hyperv_drm]
[ 770.948944] ? __pfx_vmbus_suspend+0x10/0x10 [hv_vmbus]
[ 770.948951] dpm_run_callback+0x4c/0x140
[ 770.948954] __device_suspend_noirq+0x74/0x220
[ 770.948956] dpm_noirq_suspend_devices+0x148/0x2a0
[ 770.948958] dpm_suspend_end+0x54/0xe0
[ 770.948960] create_image+0x14/0x290
[ 770.948963] hibernation_snapshot+0xd6/0x200
[ 770.948964] hibernate.cold+0x8b/0x1fb
[ 770.948967] state_store+0xcd/0xd0
[ 770.948969] kernfs_fop_write_iter+0x124/0x1b0
[ 770.948973] new_sync_write+0xff/0x190
[ 770.948976] vfs_write+0x1ef/0x280
[ 770.948978] ksys_write+0x5f/0xe0
[ 770.948979] do_syscall_64+0x5c/0x90
[ 770.948981] ? syscall_exit_work+0x103/0x130
[ 770.948983] ? syscall_exit_to_user_mode+0x12/0x30
[ 770.948985] ? do_syscall_64+0x69/0x90
[ 770.948986] ? do_syscall_64+0x69/0x90
[ 770.948987] ? do_user_addr_fault+0x1d6/0x6a0
[ 770.948989] ? do_syscall_64+0x69/0x90
[ 770.948990] ? exc_page_fault+0x62/0x150
[ 770.948992] entry_SYSCALL_64_after_hwframe+0x72/0xdc
[ 770.948995] RIP: 0033:0x7ff1b293eba7
[ 770.949010] Code: 0b 00 f7 d8 64 89 02 48 c7 c0 ff ff ff ff eb b7 0f 1f 00 f3 0f 1e fa 64 8b 04 25 18 00 00 00 85 c0 75 10 b8 01 00 00 00 0f 05 <48> 3d 00 f0 ff ff 77 51 c3 48 83 ec 28 48 89 54 24 18 48 89 74 24
[ 770.949011] RSP: 002b:00007ffde3912128 EFLAGS: 00000246 ORIG_RAX: 0000000000000001
[ 770.949012] RAX: ffffffffffffffda RBX: 0000000000000005 RCX: 00007ff1b293eba7
[ 770.949013] RDX: 0000000000000005 RSI: 00007ffde3912210 RDI: 0000000000000004
[ 770.949014] RBP: 00007ffde3912210 R08: 000055d7dd4c9510 R09: 00007ff1b29b14e0
[ 770.949014] R10: 00007ff1b29b13e0 R11: 0000000000000246 R12: 0000000000000005
[ 770.949015] R13: 000055d7dd4c53e0 R14: 0000000000000005 R15: 00007ff1b29f69e0
[ 770.949016] </TASK>
[ 770.949017] ---[ end trace e6fa0618bfa2f31d ]---
Built-on: Rhel9, Ubuntu22
Signed-off-by: Shradha Gupta <shradhagupta@linux.microsoft.com>
Signed-off-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://patchwork.freedesktop.org/patch/msgid/1706856208-9617-1-git-send-email-shradhagupta@linux.microsoft.com
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| #
12bbe2c2 |
| 08-Mar-2024 |
Jani Nikula <jani.nikula@intel.com> |
drm/probe-helper: warn about negative .get_modes()
[ Upstream commit 7af03e688792293ba33149fb8df619a8dff90e80 ]
The .get_modes() callback is supposed to return the number of modes,
never a negative
drm/probe-helper: warn about negative .get_modes()
[ Upstream commit 7af03e688792293ba33149fb8df619a8dff90e80 ]
The .get_modes() callback is supposed to return the number of modes,
never a negative error code. If a negative value is returned, it'll just
be interpreted as a negative count, and added to previous calculations.
Document the rules, but handle the negative values gracefully with an
error message.
Cc: stable@vger.kernel.org
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/50208c866facc33226a3c77b82bb96aeef8ef310.1709913674.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
| #
12bbe2c2 |
| 08-Mar-2024 |
Jani Nikula <jani.nikula@intel.com> |
drm/probe-helper: warn about negative .get_modes()
[ Upstream commit 7af03e688792293ba33149fb8df619a8dff90e80 ]
The .get_modes() callback is supposed to return the number of modes,
never a negative
drm/probe-helper: warn about negative .get_modes()
[ Upstream commit 7af03e688792293ba33149fb8df619a8dff90e80 ]
The .get_modes() callback is supposed to return the number of modes,
never a negative error code. If a negative value is returned, it'll just
be interpreted as a negative count, and added to previous calculations.
Document the rules, but handle the negative values gracefully with an
error message.
Cc: stable@vger.kernel.org
Acked-by: Thomas Zimmermann <tzimmermann@suse.de>
Link: https://patchwork.freedesktop.org/patch/msgid/50208c866facc33226a3c77b82bb96aeef8ef310.1709913674.git.jani.nikula@intel.com
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Sasha Levin <sashal@kernel.org>
show more ...
|
|
Revision tags: v6.6.15, v6.6.14, v6.6.13, v6.6.12, v6.6.11, v6.6.10, v6.6.9, v6.6.8, v6.6.7, v6.6.6, v6.6.5, v6.6.4, v6.6.3, v6.6.2, v6.5.11, v6.6.1, v6.5.10, v6.6, v6.5.9, v6.5.8, v6.5.7, v6.5.6, v6.5.5, v6.5.4, v6.5.3, v6.5.2, v6.1.51, v6.5.1, v6.1.50, v6.5, v6.1.49, v6.1.48 |
|
| #
c67b06f1 |
| 22-Aug-2023 |
Imre Deak <imre.deak@intel.com> |
drm: Add an HPD poll helper to reschedule the poll work
Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since p
drm: Add an HPD poll helper to reschedule the poll work
Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since previously polling was disabled for all connectors and hence
output_poll_work was not running).
This is needed by the next patch fixing HPD polling on i915.
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-1-imre.deak@intel.com
(cherry picked from commit fe2352fd64029918174de4b460dfe6df0c6911cd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
show more ...
|
| #
a94e7ccf |
| 22-Aug-2023 |
Imre Deak <imre.deak@intel.com> |
drm: Add an HPD poll helper to reschedule the poll work
Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since p
drm: Add an HPD poll helper to reschedule the poll work
Add a helper to reschedule drm_mode_config::output_poll_work after
polling has been enabled for a connector (and needing a reschedule,
since previously polling was disabled for all connectors and hence
output_poll_work was not running).
This is needed by the next patch fixing HPD polling on i915.
CC: stable@vger.kernel.org # 6.4+
Cc: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Cc: dri-devel@lists.freedesktop.org
Reviewed-by: Jouni Högander <jouni.hogander@intel.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Imre Deak <imre.deak@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20230822113015.41224-1-imre.deak@intel.com
(cherry picked from commit fe2352fd64029918174de4b460dfe6df0c6911cd)
Signed-off-by: Rodrigo Vivi <rodrigo.vivi@intel.com>
show more ...
|
|
Revision tags: v6.1.46, v6.1.45, v6.1.44, v6.1.43, v6.1.42, v6.1.41, v6.1.40, v6.1.39, v6.1.38, v6.1.37, v6.1.36, v6.4, v6.1.35, v6.1.34, v6.1.33, v6.1.32, v6.1.31, v6.1.30, v6.1.29, v6.1.28, v6.1.27, v6.1.26, v6.3, v6.1.25, v6.1.24, v6.1.23, v6.1.22, v6.1.21, v6.1.20, v6.1.19, v6.1.18, v6.1.17, v6.1.16, v6.1.15, v6.1.14, v6.1.13, v6.2, v6.1.12, v6.1.11, v6.1.10, v6.1.9 |
|
| #
a8e47884 |
| 27-Jan-2023 |
Dom Cobley <popcornmix@gmail.com> |
drm/probe-helper: Cancel previous job before starting new one
Currently we schedule a call to output_poll_execute from
drm_kms_helper_poll_enable for 10s in future. Later we try to replace
that in d
drm/probe-helper: Cancel previous job before starting new one
Currently we schedule a call to output_poll_execute from
drm_kms_helper_poll_enable for 10s in future. Later we try to replace
that in drm_helper_probe_single_connector_modes with a 0s schedule with
delayed_event set.
But as there is already a job in the queue this fails, and the immediate
job we wanted with delayed_event set doesn't occur until 10s later.
And that call acts as if connector state has changed, reprobing modes.
This has a side effect of waking up a display that has been blanked.
Make sure we cancel the old job before submitting the immediate one.
Fixes: 162b6a57ac50 ("drm/probe-helper: don't lose hotplug event")
Acked-by: Daniel Vetter <daniel@ffwll.ch>
Signed-off-by: Dom Cobley <popcornmix@gmail.com>
[Maxime: Switched to mod_delayed_work]
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
Link: https://patchwork.freedesktop.org/patch/msgid/20230127154052.452524-1-maxime@cerno.tech
show more ...
|
| #
a4e77172 |
| 24-Jan-2023 |
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
drm/probe_helper: sort out poll_running vs poll_enabled
There are two flags attemting to guard connector polling:
poll_enabled and poll_running. While poll_enabled semantics is clearly
defined and f
drm/probe_helper: sort out poll_running vs poll_enabled
There are two flags attemting to guard connector polling:
poll_enabled and poll_running. While poll_enabled semantics is clearly
defined and fully adhered (mark that drm_kms_helper_poll_init() was
called and not finalized by the _fini() call), the poll_running flag
doesn't have such clearliness.
This flag is used only in drm_helper_probe_single_connector_modes() to
guard calling of drm_kms_helper_poll_enable, it doesn't guard the
drm_kms_helper_poll_fini(), etc. Change it to only be set if the polling
is actually running. Tie HPD enablement to this flag.
This fixes the following warning reported after merging the HPD series:
Hot plug detection already enabled
WARNING: CPU: 2 PID: 9 at drivers/gpu/drm/drm_bridge.c:1257 drm_bridge_hpd_enable+0x94/0x9c [drm]
Modules linked in: videobuf2_memops snd_soc_simple_card snd_soc_simple_card_utils fsl_imx8_ddr_perf videobuf2_common snd_soc_imx_spdif adv7511 etnaviv imx8m_ddrc imx_dcss mc cec nwl_dsi gov
CPU: 2 PID: 9 Comm: kworker/u8:0 Not tainted 6.2.0-rc2-15208-g25b283acd578 #6
Hardware name: NXP i.MX8MQ EVK (DT)
Workqueue: events_unbound deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : drm_bridge_hpd_enable+0x94/0x9c [drm]
lr : drm_bridge_hpd_enable+0x94/0x9c [drm]
sp : ffff800009ef3740
x29: ffff800009ef3740 x28: ffff000009331f00 x27: 0000000000001000
x26: 0000000000000020 x25: ffff800001148ed8 x24: ffff00000a8fe000
x23: 00000000fffffffd x22: ffff000005086348 x21: ffff800001133ee0
x20: ffff00000550d800 x19: ffff000005086288 x18: 0000000000000006
x17: 0000000000000000 x16: ffff8000096ef008 x15: 97ffff2891004260
x14: 2a1403e194000000 x13: 97ffff2891004260 x12: 2a1403e194000000
x11: 7100385f29400801 x10: 0000000000000aa0 x9 : ffff800008112744
x8 : ffff000000250b00 x7 : 0000000000000003 x6 : 0000000000000011
x5 : 0000000000000000 x4 : ffff0000bd986a48 x3 : 0000000000000001
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000000250000
Call trace:
drm_bridge_hpd_enable+0x94/0x9c [drm]
drm_bridge_connector_enable_hpd+0x2c/0x3c [drm_kms_helper]
drm_kms_helper_poll_enable+0x94/0x10c [drm_kms_helper]
drm_helper_probe_single_connector_modes+0x1a8/0x510 [drm_kms_helper]
drm_client_modeset_probe+0x204/0x1190 [drm]
__drm_fb_helper_initial_config_and_unlock+0x5c/0x4a4 [drm_kms_helper]
drm_fb_helper_initial_config+0x54/0x6c [drm_kms_helper]
drm_fbdev_client_hotplug+0xd0/0x140 [drm_kms_helper]
drm_fbdev_generic_setup+0x90/0x154 [drm_kms_helper]
dcss_kms_attach+0x1c8/0x254 [imx_dcss]
dcss_drv_platform_probe+0x90/0xfc [imx_dcss]
platform_probe+0x70/0xcc
really_probe+0xc4/0x2e0
__driver_probe_device+0x80/0xf0
driver_probe_device+0xe0/0x164
__device_attach_driver+0xc0/0x13c
bus_for_each_drv+0x84/0xe0
__device_attach+0xa4/0x1a0
device_initial_probe+0x1c/0x30
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xd0
process_one_work+0x200/0x474
worker_thread+0x74/0x43c
kthread+0xfc/0x110
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
Reported-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Fixes: c8268795c9a9 ("drm/probe-helper: enable and disable HPD on connectors")
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Tested-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124104548.3234554-2-dmitry.baryshkov@linaro.org
(cherry picked from commit d33a54e3991dfce88b4fc6d9c3360951c2c5660d)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
show more ...
|
| #
91f43949 |
| 24-Jan-2023 |
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
drm/probe_helper: extract two helper functions
Extract drm_kms_helper_enable_hpd() and drm_kms_helper_disable_hpd(),
two helpers that enable and disable HPD handling on all device's
connectors.
Sig
drm/probe_helper: extract two helper functions
Extract drm_kms_helper_enable_hpd() and drm_kms_helper_disable_hpd(),
two helpers that enable and disable HPD handling on all device's
connectors.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124104548.3234554-1-dmitry.baryshkov@linaro.org
(cherry picked from commit cbf143b282c64e59559cc8351c0b5b1ab4bbdcbe)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
show more ...
|
| #
d33a54e3 |
| 24-Jan-2023 |
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
drm/probe_helper: sort out poll_running vs poll_enabled
There are two flags attemting to guard connector polling:
poll_enabled and poll_running. While poll_enabled semantics is clearly
defined and f
drm/probe_helper: sort out poll_running vs poll_enabled
There are two flags attemting to guard connector polling:
poll_enabled and poll_running. While poll_enabled semantics is clearly
defined and fully adhered (mark that drm_kms_helper_poll_init() was
called and not finalized by the _fini() call), the poll_running flag
doesn't have such clearliness.
This flag is used only in drm_helper_probe_single_connector_modes() to
guard calling of drm_kms_helper_poll_enable, it doesn't guard the
drm_kms_helper_poll_fini(), etc. Change it to only be set if the polling
is actually running. Tie HPD enablement to this flag.
This fixes the following warning reported after merging the HPD series:
Hot plug detection already enabled
WARNING: CPU: 2 PID: 9 at drivers/gpu/drm/drm_bridge.c:1257 drm_bridge_hpd_enable+0x94/0x9c [drm]
Modules linked in: videobuf2_memops snd_soc_simple_card snd_soc_simple_card_utils fsl_imx8_ddr_perf videobuf2_common snd_soc_imx_spdif adv7511 etnaviv imx8m_ddrc imx_dcss mc cec nwl_dsi gov
CPU: 2 PID: 9 Comm: kworker/u8:0 Not tainted 6.2.0-rc2-15208-g25b283acd578 #6
Hardware name: NXP i.MX8MQ EVK (DT)
Workqueue: events_unbound deferred_probe_work_func
pstate: 60000005 (nZCv daif -PAN -UAO -TCO -DIT -SSBS BTYPE=--)
pc : drm_bridge_hpd_enable+0x94/0x9c [drm]
lr : drm_bridge_hpd_enable+0x94/0x9c [drm]
sp : ffff800009ef3740
x29: ffff800009ef3740 x28: ffff000009331f00 x27: 0000000000001000
x26: 0000000000000020 x25: ffff800001148ed8 x24: ffff00000a8fe000
x23: 00000000fffffffd x22: ffff000005086348 x21: ffff800001133ee0
x20: ffff00000550d800 x19: ffff000005086288 x18: 0000000000000006
x17: 0000000000000000 x16: ffff8000096ef008 x15: 97ffff2891004260
x14: 2a1403e194000000 x13: 97ffff2891004260 x12: 2a1403e194000000
x11: 7100385f29400801 x10: 0000000000000aa0 x9 : ffff800008112744
x8 : ffff000000250b00 x7 : 0000000000000003 x6 : 0000000000000011
x5 : 0000000000000000 x4 : ffff0000bd986a48 x3 : 0000000000000001
x2 : 0000000000000000 x1 : 0000000000000000 x0 : ffff000000250000
Call trace:
drm_bridge_hpd_enable+0x94/0x9c [drm]
drm_bridge_connector_enable_hpd+0x2c/0x3c [drm_kms_helper]
drm_kms_helper_poll_enable+0x94/0x10c [drm_kms_helper]
drm_helper_probe_single_connector_modes+0x1a8/0x510 [drm_kms_helper]
drm_client_modeset_probe+0x204/0x1190 [drm]
__drm_fb_helper_initial_config_and_unlock+0x5c/0x4a4 [drm_kms_helper]
drm_fb_helper_initial_config+0x54/0x6c [drm_kms_helper]
drm_fbdev_client_hotplug+0xd0/0x140 [drm_kms_helper]
drm_fbdev_generic_setup+0x90/0x154 [drm_kms_helper]
dcss_kms_attach+0x1c8/0x254 [imx_dcss]
dcss_drv_platform_probe+0x90/0xfc [imx_dcss]
platform_probe+0x70/0xcc
really_probe+0xc4/0x2e0
__driver_probe_device+0x80/0xf0
driver_probe_device+0xe0/0x164
__device_attach_driver+0xc0/0x13c
bus_for_each_drv+0x84/0xe0
__device_attach+0xa4/0x1a0
device_initial_probe+0x1c/0x30
bus_probe_device+0xa4/0xb0
deferred_probe_work_func+0x90/0xd0
process_one_work+0x200/0x474
worker_thread+0x74/0x43c
kthread+0xfc/0x110
ret_from_fork+0x10/0x20
---[ end trace 0000000000000000 ]---
Reported-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Fixes: c8268795c9a9 ("drm/probe-helper: enable and disable HPD on connectors")
Tested-by: Marek Szyprowski <m.szyprowski@samsung.com>
Tested-by: Chen-Yu Tsai <wenst@chromium.org>
Acked-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Tested-by: Laurentiu Palcu <laurentiu.palcu@oss.nxp.com>
Tested-by: Laurent Pinchart <laurent.pinchart+renesas@ideasonboard.com>
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124104548.3234554-2-dmitry.baryshkov@linaro.org
show more ...
|
| #
cbf143b2 |
| 24-Jan-2023 |
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
drm/probe_helper: extract two helper functions
Extract drm_kms_helper_enable_hpd() and drm_kms_helper_disable_hpd(),
two helpers that enable and disable HPD handling on all device's
connectors.
Sig
drm/probe_helper: extract two helper functions
Extract drm_kms_helper_enable_hpd() and drm_kms_helper_disable_hpd(),
two helpers that enable and disable HPD handling on all device's
connectors.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Neil Armstrong <neil.armstrong@linaro.org>
Reviewed-by: Jani Nikula <jani.nikula@intel.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20230124104548.3234554-1-dmitry.baryshkov@linaro.org
show more ...
|
|
Revision tags: v6.1.8 |
|
| #
c533b516 |
| 19-Jan-2023 |
Jani Nikula <jani.nikula@intel.com> |
drm/edid: add separate drm_edid_connector_add_modes()
The original goal with drm_edid_connector_update() was to have a single
call for updating the connector and adding probed modes, in this order,
drm/edid: add separate drm_edid_connector_add_modes()
The original goal with drm_edid_connector_update() was to have a single
call for updating the connector and adding probed modes, in this order,
but that turned out to be problematic. Drivers that need to update the
connector in the .detect() callback would end up updating the probed
modes as well. Turns out the callback may be called so many times that
the probed mode list fills up without bounds, and this is amplified by
add_alternate_cea_modes() duplicating the CEA modes on every call,
actually running out of memory on some machines.
Kudos to Imre Deak <imre.deak@intel.com> for explaining this to me.
Go back to having separate drm_edid_connector_update() and
drm_edid_connector_add_modes() calls. The former may be called from
.detect(), .force(), or .get_modes(), but the latter only from
.get_modes().
Unlike drm_add_edid_modes(), have drm_edid_connector_add_modes() update
the probed modes from the EDID property instead of the passed in
EDID. This is mainly to enforce two things:
1) drm_edid_connector_update() must be called before
drm_edid_connector_add_modes().
Display info and quirks are needed for parsing the modes, and we
don't want to call update_display_info() again to ensure the info is
available, like drm_add_edid_modes() does.
2) The same EDID is used for both updating the connector and adding the
probed modes.
Fortunately, the change is easy, because no driver has actually adopted
drm_edid_connector_update(). Not even i915, and that's mainly because of
the problem described above.
Cc: Imre Deak <imre.deak@intel.com>
Cc: Ville Syrjälä <ville.syrjala@linux.intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/e86fff1579f14ebf6334692526c8f6831cd02cac.1674144945.git.jani.nikula@intel.com
show more ...
|
|
Revision tags: v6.1.7, v6.1.6, v6.1.5, v6.0.19, v6.0.18, v6.1.4, v6.1.3, v6.0.17, v6.1.2, v6.0.16, v6.1.1, v6.0.15, v6.0.14, v6.0.13, v6.1, v6.0.12, v6.0.11, v6.0.10, v5.15.80, v6.0.9, v5.15.79, v6.0.8, v5.15.78, v6.0.7, v5.15.77 |
|
| #
c8268795 |
| 02-Nov-2022 |
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
drm/probe-helper: enable and disable HPD on connectors
Introduce two drm_connector_helper_funcs: enable_hpd() and disable_hpd().
They are called by drm_kms_helper_poll_enable() and
drm_kms_helper_po
drm/probe-helper: enable and disable HPD on connectors
Introduce two drm_connector_helper_funcs: enable_hpd() and disable_hpd().
They are called by drm_kms_helper_poll_enable() and
drm_kms_helper_poll_disable() (and thus drm_kms_helper_poll_init() and
drm_kms_helper_poll_fini()) respectively.
This allows DRM drivers to rely on drm_kms_helper_poll for enabling and
disabling HPD detection rather than doing that manually.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-3-dmitry.baryshkov@linaro.org
show more ...
|
| #
78b991cc |
| 02-Nov-2022 |
Dmitry Baryshkov <dmitry.baryshkov@linaro.org> |
drm/poll-helper: merge drm_kms_helper_poll_disable() and _fini()
Merge drm_kms_helper_poll_disable() and drm_kms_helper_poll_fini() code
into a common helper function.
Signed-off-by: Dmitry Baryshk
drm/poll-helper: merge drm_kms_helper_poll_disable() and _fini()
Merge drm_kms_helper_poll_disable() and drm_kms_helper_poll_fini() code
into a common helper function.
Signed-off-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Reviewed-by: Tomi Valkeinen <tomi.valkeinen@ideasonboard.com>
Signed-off-by: Neil Armstrong <neil.armstrong@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20221102180705.459294-2-dmitry.baryshkov@linaro.org
show more ...
|
| #
1e4a91db |
| 17-Nov-2022 |
Noralf Trønnes <noralf@tronnes.org> |
drm/probe-helper: Provide a TV get_modes helper
Most of the TV connectors will need a similar get_modes implementation
that will, depending on the drivers' capabilities, register the 480i and
576i m
drm/probe-helper: Provide a TV get_modes helper
Most of the TV connectors will need a similar get_modes implementation
that will, depending on the drivers' capabilities, register the 480i and
576i modes.
That implementation will also need to set the preferred flag and order
the modes based on the driver and users preferrence.
This is especially important to guarantee that a userspace stack such as
Xorg can start and pick up the preferred mode while maintaining a
working output.
Signed-off-by: Noralf Trønnes <noralf@tronnes.org>
Tested-by: Mateusz Kwiatkowski <kfyatek+publicgit@gmail.com>
Acked-in-principle-or-something-like-that-by: Daniel Vetter <daniel.vetter@ffwll.ch>
Link: https://lore.kernel.org/r/20220728-rpi-analog-tv-properties-v10-12-256dad125326@cerno.tech
Signed-off-by: Maxime Ripard <maxime@cerno.tech>
show more ...
|
| #
45b64fd9 |
| 03-Nov-2022 |
Thomas Zimmermann <tzimmermann@suse.de> |
drm/fb-helper: Remove unnecessary include statements
Remove include statements for <drm/drm_fb_helper.h> where it is not
required (i.e., most of them). In a few places include other header
files tha
drm/fb-helper: Remove unnecessary include statements
Remove include statements for <drm/drm_fb_helper.h> where it is not
required (i.e., most of them). In a few places include other header
files that are required by the source code.
v3:
* fix amdgpu include statements
* fix rockchip include statements
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Javier Martinez Canillas <javierm@redhat.com>
Link: https://patchwork.freedesktop.org/patch/msgid/20221103151446.2638-23-tzimmermann@suse.de
show more ...
|
|
Revision tags: v5.15.76, v6.0.6, v6.0.5, v5.15.75, v6.0.4 |
|
| #
019b9387 |
| 24-Oct-2022 |
Jani Nikula <jani.nikula@intel.com> |
drm/edid: rename drm_add_override_edid_modes() to drm_edid_override_connector_update()
Follow the naming of both EDID override functions as well as
drm_edid_connector_update(). This also matches bet
drm/edid: rename drm_add_override_edid_modes() to drm_edid_override_connector_update()
Follow the naming of both EDID override functions as well as
drm_edid_connector_update(). This also matches better what the function
does; a combination of EDID property update and add modes. Indeed it
should later be converted to call drm_edid_connector_update().
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/ba12957e0488654e8db010a3ff1534079caec972.1666614699.git.jani.nikula@intel.com
show more ...
|
|
Revision tags: v6.0.3, v6.0.2, v5.15.74, v5.15.73, v6.0.1, v5.15.72, v6.0, v5.15.71, v5.15.70, v5.15.69, v5.15.68, v5.15.67, v5.15.66 |
|
| #
216b9bba |
| 05-Sep-2022 |
Thomas Zimmermann <tzimmermann@suse.de> |
drm/probe-helper: Add drm_crtc_helper_mode_valid_fixed()
Add drm_crtc_helper_mode_valid_fixed(), which validates a given mode
against a display hardware's mode. Convert simpledrm and use it in a
few
drm/probe-helper: Add drm_crtc_helper_mode_valid_fixed()
Add drm_crtc_helper_mode_valid_fixed(), which validates a given mode
against a display hardware's mode. Convert simpledrm and use it in a
few other drivers with static modes.
v4:
* remove empty line after opening brace
v2:
* rename 'static' and 'hw' to 'fixed' everywhere
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905141648.22013-3-tzimmermann@suse.de
show more ...
|
| #
d25654b3 |
| 05-Sep-2022 |
Thomas Zimmermann <tzimmermann@suse.de> |
drm/probe-helper: Add drm_connector_helper_get_modes_fixed()
Add drm_connector_helper_get_modes_fixed(), which duplicates a single
display mode for a connector. Convert drivers.
v2:
* rename 'stat
drm/probe-helper: Add drm_connector_helper_get_modes_fixed()
Add drm_connector_helper_get_modes_fixed(), which duplicates a single
display mode for a connector. Convert drivers.
v2:
* rename 'static' and 'hw' to 'fixed' everywhere
* fix typo 'there' to 'their' (Sam)
Signed-off-by: Thomas Zimmermann <tzimmermann@suse.de>
Reviewed-by: Sam Ravnborg <sam@ravnborg.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220905141648.22013-2-tzimmermann@suse.de
show more ...
|
|
Revision tags: v5.15.65, v5.15.64, v5.15.63, v5.15.62, v5.15.61, v5.15.60, v5.15.59, v5.19, v5.15.58, v5.15.57, v5.15.56, v5.15.55, v5.15.54, v5.15.53, v5.15.52 |
|
| #
964893d3 |
| 29-Jun-2022 |
Jani Nikula <jani.nikula@intel.com> |
drm/probe-helper: add drm_connector_helper_get_modes()
Add a helper function to be used as the "default" .get_modes()
hook. This also works as an example of what the driver .get_modes()
hooks are su
drm/probe-helper: add drm_connector_helper_get_modes()
Add a helper function to be used as the "default" .get_modes()
hook. This also works as an example of what the driver .get_modes()
hooks are supposed to do regarding the new drm_edid_read*() and
drm_edid_connector_update() calls.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/d985449ed4b95971490ab7c09d2d59b58a892769.1656494768.git.jani.nikula@intel.com
show more ...
|
|
Revision tags: v5.15.51, v5.15.50, v5.15.49, v5.15.48, v5.15.47, v5.15.46 |
|
| #
019fd800 |
| 08-Jun-2022 |
Jani Nikula <jani.nikula@intel.com> |
drm/probe-helper: abstract .get_modes() connector helper call
Abstract the .get_modes() connector helper call, including the
override/firmware EDID fallback, for clarity.
Signed-off-by: Jani Nikula
drm/probe-helper: abstract .get_modes() connector helper call
Abstract the .get_modes() connector helper call, including the
override/firmware EDID fallback, for clarity.
Signed-off-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Ville Syrjälä <ville.syrjala@linux.intel.com>
Link: https://patchwork.freedesktop.org/patch/msgid/a4de51efc246e4f5bcbf7b84d66bb49aaf7fd974.1654674560.git.jani.nikula@intel.com
show more ...
|
|
Revision tags: v5.15.45 |
|
| #
fae7d186 |
| 01-Jun-2022 |
Douglas Anderson <dianders@chromium.org> |
drm/probe-helper: Default to 640x480 if no EDID on DP
If we're unable to read the EDID for a display because it's corrupt /
bogus / invalid then we'll add a set of standard modes for the
display. Si
drm/probe-helper: Default to 640x480 if no EDID on DP
If we're unable to read the EDID for a display because it's corrupt /
bogus / invalid then we'll add a set of standard modes for the
display. Since we have no true information about the connected
display, these modes are essentially guesses but better than nothing.
At the moment, none of the modes returned is marked as preferred, but
the modes are sorted such that the higher resolution modes are listed
first.
When userspace sees these modes presented by the kernel it needs to
figure out which one to pick. At least one userspace, ChromeOS [1]
seems to use the rules (which seem pretty reasonable):
1. Try to pick the first mode marked as preferred.
2. Try to pick the mode which matches the first detailed timing
descriptor in the EDID.
3. If no modes were marked as preferred then pick the first mode.
Unfortunately, userspace's rules combined with what the kernel is
doing causes us to fail section 4.2.2.6 (EDID Corruption Detection) of
the DP 1.4a Link CTS. That test case says that, while it's OK to allow
some implementation-specific fall-back modes if the EDID is bad that
userspace should _default_ to 640x480.
Let's fix this by marking 640x480 as default for DP in the no-EDID
case.
NOTES:
- In the discussion around v3 of this patch [2] there was talk about
solving this in userspace and I even implemented a patch that would
have solved this for ChromeOS, but then the discussion turned back
to solving this in the kernel.
- Also in the discussion of v3 [2] it was requested to limit this
change to just DP since folks were worried that it would break some
subtle corner case on VGA or HDMI.
[1] https://source.chromium.org/chromium/chromium/src/+/a051f741d0a15caff2251301efe081c30e0f4a96:ui/ozone/platform/drm/common/drm_util.cc;l=488
[2] https://lore.kernel.org/r/20220513130533.v3.1.I31ec454f8d4ffce51a7708a8092f8a6f9c929092@changeid
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Acked-by: Jani Nikula <jani.nikula@intel.com>
Reviewed-by: Sean Paul <seanpaul@chromium.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220601112302.v4.1.I31ec454f8d4ffce51a7708a8092f8a6f9c929092@changeid
show more ...
|
|
Revision tags: v5.15.44, v5.15.43, v5.15.42, v5.18, v5.15.41, v5.15.40, v5.15.39 |
|
| #
e7c254d7 |
| 11-May-2022 |
Douglas Anderson <dianders@chromium.org> |
drm/probe-helper: For DP, add 640x480 if all other modes are bad
As per Displayport spec section 5.2.1.2 ("Video Timing Format") says
that all detachable sinks shall support 640x480 @60Hz as a fail
drm/probe-helper: For DP, add 640x480 if all other modes are bad
As per Displayport spec section 5.2.1.2 ("Video Timing Format") says
that all detachable sinks shall support 640x480 @60Hz as a fail safe
mode.
A DP compliance test expected us to utilize the above fact when all
modes it presented to the DP source were not achievable. It presented
only modes that would be achievable with more lanes and/or higher
speeds than we had available and expected that when we couldn't do
that then we'd fall back to 640x480 even though it didn't advertise
this size.
In order to pass the compliance test (and also support any users who
might fall into a similar situation with their display), we need to
add 640x480 into the list of modes. However, we don't want to add
640x480 all the time. Despite the fact that the DP spec says all sinks
_shall support_ 640x480, they're not guaranteed to support it
_well_. Continuing to read the spec you can see that the display is
not required to really treat 640x480 equal to all the other modes. It
doesn't need to scale or anything--just display the pixels somehow for
failsafe purposes. It should also be noted that it's not hard to find
a display hooked up via DisplayPort that _doesn't_ support 640x480 at
all. The HP ZR30w screen I'm sitting in front of has a native DP port
and doesn't work at 640x480. I also plugged in a tiny 800x480 HDMI
display via a DP to HDMI adapter and that screen definitely doesn't
support 640x480.
As a compromise solution, let's only add the 640x480 mode if:
* We're on DP.
* All other modes have been pruned.
This acknowledges that 640x480 might not be the best mode to use but,
since sinks are _supposed_ to support it, we will at least fall back
to it if there's nothing else.
Note that we _don't_ add higher resolution modes like 1024x768 in this
case. We only add those modes for a failed EDID read where we have no
idea what's going on. In the case where we've pruned all modes then
instead we only want 640x480 which is the only defined "Fail Safe"
resolution.
This patch originated in response to Kuogee Hsieh's patch [1].
[1] https://lore.kernel.org/r/1650671124-14030-1-git-send-email-quic_khsieh@quicinc.com
Signed-off-by: Douglas Anderson <dianders@chromium.org>
Tested-by: Kuogee Hsieh <quic_khsieh@quicinc.com>
Reviewed-by: Abhinav Kumar <quic_abhinavk@quicinc.com>
Reviewed-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://patchwork.freedesktop.org/patch/msgid/20220511155749.v3.2.I4ac7f55aa446699f8c200a23c10463256f6f439f@changeid
show more ...
|