clk: qcom: add read-only alpha pll post divider operations

Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds th

clk: qcom: add read-only alpha pll post divider operations

Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM alpha pll
post divider which is equivalent to generic divider operations in
'commit 79c6ab509558 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support Brammo type Alpha PLL

The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed dynamically witho

clk: qcom: support Brammo type Alpha PLL

The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed dynamically without turning off the PLL.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support Huayra type Alpha PLL

The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two’s compliment nu

clk: qcom: support Huayra type Alpha PLL

The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two’s compliment number. This PLL supports
dynamic programming.

Since the decoding of alpha val and dynamic programming are
completely different from other Alpha PLLs we add separate
functions for Huayra PLLs.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support for dynamic updating the PLL

Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.

This dynamic update requ

clk: qcom: support for dynamic updating the PLL

Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.

This dynamic update requires the following sequence:

1. Write the desired values to L_VAL and ALPHA_VAL registers
2. Toggle pll_latch_input from low to high
3. Wait for pll_ack_latch to transition from low to high
The new L and alpha values have been latched. It may
take some time for the PLL to fully settle with these
new values.
4. Pull pll_latch_input low

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support for alpha mode configuration

The current configuration does not fully configure PLL alpha mode
and values so this patch

1. Configures PLL_ALPHA_VAL_U for PLL which supports 40 bi

clk: qcom: support for alpha mode configuration

The current configuration does not fully configure PLL alpha mode
and values so this patch

1. Configures PLL_ALPHA_VAL_U for PLL which supports 40 bit alpha.
2. Adds alpha enable and alpha mode configuration support.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: fix 16 bit alpha support calculation

The alpha value calculation has been written for 40-bit alpha
values which doesn't work work properly for 16-bit ones. The
alpha value is calculated o

clk: qcom: fix 16 bit alpha support calculation

The alpha value calculation has been written for 40-bit alpha
values which doesn't work work properly for 16-bit ones. The
alpha value is calculated on the basis of ALPHA_BITWIDTH to make
the computation easy for 40 bit alpha. After calculating the 32
bit alpha, it is converted to 40 bit alpha by making lower bits
zero. But if actual alpha register width is less than
ALPHA_BITWIDTH, then the actual width can be used for
calculation. This also means, during the 40 bit alpha pll set
rate path, the lower alpha register is not configured

Change the code to calculate the rate and register values from
'alpha_width' instead of hard-coding it so that it can work for
the different widths that are supported.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support for alpha pll properties

Alpha PLL is a generic name used for QCOM PLLs which uses L and
Alpha values for configuring the integer and fractional part.
QCOM SoCs use different type

clk: qcom: support for alpha pll properties

Alpha PLL is a generic name used for QCOM PLLs which uses L and
Alpha values for configuring the integer and fractional part.
QCOM SoCs use different types of Alpha PLLs for which basic
software configuration part is common with following differences.

1. All these PLLs have the same basic registers like
PLL_MODE, L_VAL, ALPHA_VAL but some of the register offsets are
different between PLLs types.

2. The dynamic programming sequence is different in some
of the Alpha PLLs

3. Some of the PLLs don’t have 64 bit config control, 64 bit
user control, VCO configuration, etc.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: Enable FSM mode for votable alpha PLLs

The votable alpha PLLs need to have the fsm mode enabled as part
of the initialization. The sequence seems to be the same as used
by clk-pll, so mov

clk: qcom: Enable FSM mode for votable alpha PLLs

The votable alpha PLLs need to have the fsm mode enabled as part
of the initialization. The sequence seems to be the same as used
by clk-pll, so move the function which does this into a common
place and reuse it for the clk-alpha-pll

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: handle alpha PLLs with 16bit alpha val registers

Some alpha PLLs have support for only a 16bit programable Alpha Value
(as against the default 40bits). Add a flag to handle the 16bit alph

clk: qcom: handle alpha PLLs with 16bit alpha val registers

Some alpha PLLs have support for only a 16bit programable Alpha Value
(as against the default 40bits). Add a flag to handle the 16bit alpha
registers

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: Add support to initialize alpha plls

Add a function to do initial configuration of the alpha plls

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd

clk: qcom: Add support to initialize alpha plls

Add a function to do initial configuration of the alpha plls

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: Add support for alpha pll hwfsm ops

Some PLLs can support an HW FSM mode (different from the Votable FSMs,
though its the same bit used to enable Votable FSMs as well as HW FSMs)
which en

clk: qcom: Add support for alpha pll hwfsm ops

Some PLLs can support an HW FSM mode (different from the Votable FSMs,
though its the same bit used to enable Votable FSMs as well as HW FSMs)
which enables the HW to do the bypass/reset/enable-output-ctrl sequence
on its own. So all thats needed from SW is to set the FSM_ENA bit.
PLL_ACTIVE_FLAG is whats used to check if the PLL is active/enabled.

Some of the PLLs which support HW FSM can also need an OFFLINE request
that needs to be toggled across the enable/disable. We use a flag to
identify such cases and handle them.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: Add Alpha PLL support

Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controlle

clk: qcom: Add Alpha PLL support

Add support for configuring rates of, enabling, and disabling
Alpha PLLs. This is sufficient for the types of PLLs found in
the global and multimedia clock controllers.

Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: clk-alpha-pll: use the right PCAL_DONE value for lucid pll

Lucid PCAL_DONE is different from trion.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitr

clk: qcom: clk-alpha-pll: use the right PCAL_DONE value for lucid pll

Lucid PCAL_DONE is different from trion.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-5-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid

Fixed ops were already identical, this adds support for non-fixed ops by
sharing between trion and lucid.

This al

clk: qcom: clk-alpha-pll: same regs and ops for trion and lucid

Fixed ops were already identical, this adds support for non-fixed ops by
sharing between trion and lucid.

This also changes the names for trion ops to be consistent with the rest.

Note LUCID_PCAL_DONE is renamed to TRION_PCAL_DONE because it is wrong for
lucid, LUCID_PCAL_DONE should be BIT(27). Next patch will address this.

Signed-off-by: Jonathan Marek <jonathan@marek.ca>
Tested-by: Dmitry Baryshkov <dmitry.baryshkov@linaro.org>
Link: https://lore.kernel.org/r/20200709135251.643-4-jonathan@marek.ca
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: Add CPU clock driver for msm8996

Each of the CPU clusters (Power and Perf) on msm8996 are
clocked via 2 PLLs, a primary and alternate. There are also
2 Mux'es, a primary a

clk: qcom: Add CPU clock driver for msm8996

Each of the CPU clusters (Power and Perf) on msm8996 are
clocked via 2 PLLs, a primary and alternate. There are also
2 Mux'es, a primary and secondary all connected together
as shown below

+-------+
XO | |
+------------------>0 |
| |
PLL/2 | SMUX +----+
+------->1 | |
| | | |
| +-------+ | +-------+
| +---->0 |
| | |
+---------------+ | +----------->1 | CPU clk
|Primary PLL +----+ PLL_EARLY | | +------>
| +------+-----------+ +------>2 PMUX |
+---------------+ | | | |
| +------+ | +-->3 |
+--^+ ACD +-----+ | +-------+
+---------------+ +------+ |
|Alt PLL | |
| +---------------------------+
+---------------+ PLL_EARLY

The primary PLL is what drives the CPU clk, except for times
when we are reprogramming the PLL itself (for rate changes) when
we temporarily switch to an alternate PLL. A subsequent patch adds
support to switch between primary and alternate PLL during rate
changes.

The primary PLL operates on a single VCO range, between 600MHz
and 3GHz. However the CPUs do support OPPs with frequencies
between 300MHz and 600MHz. In order to support running the CPUs
at those frequencies we end up having to lock the PLL at twice
the rate and drive the CPU clk via the PLL/2 output and SMUX.

So for frequencies above 600MHz we follow the following path
Primary PLL --> PLL_EARLY --> PMUX(1) --> CPU clk
and for frequencies between 300MHz and 600MHz we follow
Primary PLL --> PLL/2 --> SMUX(1) --> PMUX(0) --> CPU clk

ACD stands for Adaptive Clock Distribution and is used to
detect voltage droops.

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Rajendra Nayak: Initial RFC - https://lkml.org/lkml/2016/9/29/84

Signed-off-by: Ilia Lin <ilialin@codeaurora.org>
Ilia Lin: - reworked clock registering
- Added clock-tree diagram
- non-builtin support
- clock notifier on rate change
- https://lkml.org/lkml/2018/5/24/123

Signed-off-by: Loic Poulain <loic.poulain@linaro.org>
Loic Poulain: - fixed driver remove / clk deregistering
- Removed useless memory barriers
- devm usage when possible
- Fixed Kconfig depends

Link: https://lore.kernel.org/r/1593766185-16346-3-git-send-email-loic.poulain@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: clk-alpha-pll: Add support for controlling Lucid PLLs

Add programming sequence support for managing the Lucid PLLs.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
Si

clk: qcom: clk-alpha-pll: Add support for controlling Lucid PLLs

Add programming sequence support for managing the Lucid PLLs.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Venkata Narendra Kumar Gutta <vnkgutta@codeaurora.org>
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20200224045003.3783838-4-vkoul@kernel.org
Reviewed-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Tested-by: Bryan O'Donoghue <bryan.odonoghue@linaro.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration

In the cases where the PLL is not calibrated the PLL could fail to lock.
Add support for prepare ops which would take care

clk: qcom: clk-alpha-pll: Add support for Fabia PLL calibration

In the cases where the PLL is not calibrated the PLL could fail to lock.
Add support for prepare ops which would take care of the same.

Fabia PLL user/test control registers might required to be configured, so
add support for configuring them.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
Link: https://lkml.kernel.org/r/1573812304-24074-3-git-send-email-tdas@codeaurora.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: gcc: limit GPLL0_AO_OUT operating frequency

Limit the GPLL0_AO_OUT_MAIN operating frequency as per its hardware
specifications.

Co-developed-by: Niklas Cassel <niklas

clk: qcom: gcc: limit GPLL0_AO_OUT operating frequency

Limit the GPLL0_AO_OUT_MAIN operating frequency as per its hardware
specifications.

Co-developed-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Niklas Cassel <niklas.cassel@linaro.org>
Signed-off-by: Jorge Ramirez-Ortiz <jorge.ramirez-ortiz@linaro.org>
Reviewed-by: Bjorn Andersson <bjorn.andersson@linaro.org>
Acked-by: Stephen Boyd <sboyd@kernel.org>
Link: https://lkml.kernel.org/r/20191125135910.679310-3-niklas.cassel@linaro.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: clk-alpha-pll: Add support for Trion PLLs

Add programming sequence support for managing the Trion
PLLs.

Signed-off-by: Deepak Katragadda <dkatraga@codeaurora.org>

clk: qcom: clk-alpha-pll: Add support for Trion PLLs

Add programming sequence support for managing the Trion
PLLs.

Signed-off-by: Deepak Katragadda <dkatraga@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
[vkoul: port to upstream and tidy-up
use upstream way of specifying PLLs]
Signed-off-by: Vinod Koul <vkoul@kernel.org>
Link: https://lkml.kernel.org/r/20190722074348.29582-4-vkoul@kernel.org
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: Update SPDX headers for common files

SPDX headers updated for common/branch/pll/regmap files.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen B

clk: qcom: Update SPDX headers for common files

SPDX headers updated for common/branch/pll/regmap files.

Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: Add support for controlling Fabia PLL

Fabia PLL is a Digital Frequency Locked Loop (DFLL) clock
generator which has a wide range of frequency output. It
supports dynamic u

clk: qcom: Add support for controlling Fabia PLL

Fabia PLL is a Digital Frequency Locked Loop (DFLL) clock
generator which has a wide range of frequency output. It
supports dynamic updating of the output frequency
("frequency slewing") without need to turn off the PLL
before configuration. Add support for initial configuration
and programming sequence to control fabia PLLs.

Signed-off-by: Amit Nischal <anischal@codeaurora.org>
[sboyd: Shorten code a little]
Signed-off-by: Stephen Boyd <sboyd@kernel.org>

show more ...

clk: qcom: add read-only alpha pll post divider operations

Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This

clk: qcom: add read-only alpha pll post divider operations

Some of the divider settings are preconfigured and should not
be changed by the clock framework during frequency change. This
patch adds the read-only divider operation for QCOM alpha pll
post divider which is equivalent to generic divider operations in
'commit 79c6ab509558 ("clk: divider: add CLK_DIVIDER_READ_ONLY flag")'.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support Brammo type Alpha PLL

The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed d

clk: qcom: support Brammo type Alpha PLL

The Brammo type of Alpha PLL doesn't allow configuration of a
VCO, but it does support dynamic update in which the frequency
can be changed dynamically without turning off the PLL.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support Huayra type Alpha PLL

The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two

clk: qcom: support Huayra type Alpha PLL

The Huayra type Alpha PLL has a 16 bit alpha value, and
depending on the alpha_mode, the alpha value can be treated as
M/N value or as a two’s compliment number. This PLL supports
dynamic programming.

Since the decoding of alpha val and dynamic programming are
completely different from other Alpha PLLs we add separate
functions for Huayra PLLs.

Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...

clk: qcom: support for dynamic updating the PLL

Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.

This

clk: qcom: support for dynamic updating the PLL

Some of the Alpha PLLs support dynamic update in which the
frequency can be changed dynamically without turning off the PLL.

This dynamic update requires the following sequence:

1. Write the desired values to L_VAL and ALPHA_VAL registers
2. Toggle pll_latch_input from low to high
3. Wait for pll_ack_latch to transition from low to high
The new L and alpha values have been latched. It may
take some time for the PLL to fully settle with these
new values.
4. Pull pll_latch_input low

Signed-off-by: Rajendra Nayak <rnayak@codeaurora.org>
Signed-off-by: Taniya Das <tdas@codeaurora.org>
Signed-off-by: Abhishek Sahu <absahu@codeaurora.org>
Signed-off-by: Stephen Boyd <sboyd@codeaurora.org>

show more ...